Paul Horn DSRV.5.16.88.16 TS3K
End mills as Schlichtfäser for soft and hard milling, corner radius 1 mm, 5 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DST.2.04.05.063.06 TS3H
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.04.05.063.06 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.04.05.077.06 TS3H
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.04.05.077.06 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.04.10.063.06 TS3H
End mills for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.04.10.063.06 TS3K
End mills for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.04.10.077.06 TS3K
End mills for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.04.1008.03.06 HD05
End mills for soft and hard milling, corner radius 0 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.04.2015.03.06 HD05
End mills for soft and hard milling, corner radius 0 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.05.05.063.06 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.05.05.077.06 TS3H
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.05.05.077.06 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.05.10.063.06 TS3H
End mills for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.05.10.063.06 TS3K
End mills for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.05.10.077.06 TS3H
End mills for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.05.10.077.06 TS3K
End mills for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.06.05.063.06 TS3H
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.06.05.063.06 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.06.05.077.06 TS3H
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.06.05.077.06 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.06.05.099.08 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.06.15.063.06 TS3H
End mills for soft and hard milling, corner radius 1.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.06.15.063.06 TS3K
End mills for soft and hard milling, corner radius 1.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.06.15.077.06 TS3H
End mills for soft and hard milling, corner radius 1.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.06.15.077.06 TS3K
End mills for soft and hard milling, corner radius 1.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.06.15.099.08 TS3H
End mills for soft and hard milling, corner radius 1.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.06.15.099.08 TS3K
End mills for soft and hard milling, corner radius 1.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.06.1510.04.06 HD08
End mills for soft and hard milling, corner radius 0 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.06.2015.04.06 HD08
End mills for soft and hard milling, corner radius 0 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.06.2520.04.06 HD08
End mills for soft and hard milling, corner radius 0 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.06.3060.03.06 HD08
Torus for soft and hard milling, corner radius 0.3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.06.3060.05.06 HD08
Torus for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.06.3060.10.06 HD08
Torus for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.08.05.063.08 TS3H
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.05.063.08 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.05.077.08 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.10.063.08 TS3K
End mills for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.10.077.08 TS3H
End mills for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.10.077.08 TS3K
End mills for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.10.099.08 TS3H
End mills for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.10.099.08 TS3K
End mills for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.10.119.10 TS3H
End mills for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 10 mm.
Paul Horn DST.2.08.1510.06.08 HD08
End mills for soft and hard milling, corner radius 0 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.20.063.08 TS3H
End mills for soft and hard milling, corner radius 2 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.20.063.08 TS3K
End mills for soft and hard milling, corner radius 2 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.20.077.08 TS3H
End mills for soft and hard milling, corner radius 2 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.20.077.08 TS3K
End mills for soft and hard milling, corner radius 2 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.20.099.08 TS3K
End mills for soft and hard milling, corner radius 2 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.20.119.10 TS3H
End mills for soft and hard milling, corner radius 2 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 10 mm.
Paul Horn DST.2.08.20.119.10 TS3K
End mills for soft and hard milling, corner radius 2 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 10 mm.
Paul Horn DST.2.08.2015.06.08 HD08
End mills for soft and hard milling, corner radius 0 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.2570.03.08 HD08
Torus for soft and hard milling, corner radius 0.3 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.2570.05.08 HD08
Torus for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.2570.10.08 HD08
Torus for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.3020.06.08 HD08
End mills for soft and hard milling, corner radius 0 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.4070.03.08 HD08
Torus for soft and hard milling, corner radius 0.3 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.4070.05.08 HD08
Torus for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.08.4070.10.08 HD08
Torus for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.2.10.05.077.10 TS3H
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.2.10.05.077.10 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.2.10.10.099.10 TS3H
End mills for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.2.10.10.099.10 TS3K
End mills for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.2.10.20.077.10 TS3H
End mills for soft and hard milling, corner radius 2 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.2.10.20.077.10 TS3K
End mills for soft and hard milling, corner radius 2 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.2.10.20.099.10 TS3K
End mills for soft and hard milling, corner radius 2 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.2.10.20.119.12 TS3H
End mills for soft and hard milling, corner radius 2 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 12 mm.
Paul Horn DST.2.10.20.119.12 TS3K
End mills for soft and hard milling, corner radius 2 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 12 mm.
Paul Horn DST.2.10.2010.08.10 HD08
End mills for soft and hard milling, corner radius 0 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.2.10.2515.08.10 HD08
End mills for soft and hard milling, corner radius 0 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.2.10.3020.08.10 HD08
End mills for soft and hard milling, corner radius 0 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.2.10.3080.05.10 HD08
Torus for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.2.10.3080.10.10 HD08
Torus for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.2.10.5080.05.10 HD08
Torus for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.2.10.5080.10.10 HD08
Torus for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.2.12.05.077.12 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DST.2.12.10.099.12 TS3K
End mills for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DST.2.12.20.077.12 TS3H
End mills for soft and hard milling, corner radius 2 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DST.2.12.20.099.12 TS3H
End mills for soft and hard milling, corner radius 2 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DST.2.12.20.099.12 TS3K
End mills for soft and hard milling, corner radius 2 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DST.2.12.2010.10.12 HD08
End mills for soft and hard milling, corner radius 0 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DST.2.12.2515.10.12 HD08
End mills for soft and hard milling, corner radius 0 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DST.2.12.3020.10.12 HD08
End mills for soft and hard milling, corner radius 0 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DST.2.12.3090.05.12 HD08
Torus for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DST.2.12.3090.10.12 HD08
Torus for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DST.2.12.6090.05.12 HD08
Torus for soft and hard milling, corner radius 0.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DST.2.12.6090.10.12 HD08
Torus for soft and hard milling, corner radius 1 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DST.2.15.03.063.06 TS3H
End mills for soft and hard milling, corner radius 0.3 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.15.03.063.06 TS3K
End mills for soft and hard milling, corner radius of 0.9 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm.
Paul Horn DST.2.16.2510.20.16 HD08
End mills for soft and hard milling, corner radius 0 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DST.2.16.3015.20.16 HD08
End mills for soft and hard milling, corner radius 0 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DST.2.16.3520.20.16 HD08
End mills for soft and hard milling, corner radius 0 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DST.2.160.20.149.16 TS3H
End mills for soft and hard milling, corner radius 2 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DST.2.160.20.149.16 TS3K
End mills for soft and hard milling, corner radius 2 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DST.2.160.35.099.16 TS3H
End mills for soft and hard milling, corner radius 3.5 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DST.2.160.35.099.16 TS3K
End mills for soft and hard milling, corner radius 3.5 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DST.2.160.35.149.16 TS3H
End mills for soft and hard milling, corner radius 3.5 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DST.2.160.35.149.16 TS3K
End mills for soft and hard milling, corner radius 3.5 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DST.4.06.063.06.3.05 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 4-edged, with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.4.06.063.06.3.10 TS3K
End mills for soft and hard milling, corner radius 1 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.4.06.077.06.3.05 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 4-edged, with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.4.06.077.06.3.15 TS3K
End mills for soft and hard milling, corner radius 1.5 mm, 4-edged, with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DST.4.06.099.08.3.05 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 4-edged, with a diameter of 6 mm and a shaft diameter of 8 mm.
Paul Horn DST.4.06.099.08.3.15 TS3K
End mills for soft and hard milling, corner radius 1.5 mm, 4-edged, with a diameter of 6 mm and a shaft diameter of 8 mm.
Paul Horn DST.4.08.063.08.3.05 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 4-edged, with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.4.08.063.08.3.10 TS3K
End mills for soft and hard milling, corner radius 1 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.4.08.063.08.3.20 TS3K
End mills for soft and hard milling, corner radius 2 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.4.08.077.08.3.05 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 4-edged, with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.4.08.077.08.3.10 TS3K
End mills for soft and hard milling, corner radius 1 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.4.08.077.08.3.20 TS3K
End mills for soft and hard milling, corner radius 2 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.4.08.099.08.3.10 TS3K
End mills for soft and hard milling, corner radius 1 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.4.08.099.08.3.20 TS3K
End mills for soft and hard milling, corner radius 2 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DST.4.08.119.10.3.20 TS3K
End mills for soft and hard milling, corner radius 2 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 10 mm.
Paul Horn DST.4.10.077.10.3.05 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 4-edged, with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.4.10.077.10.3.20 TS3K
End mills for soft and hard milling, corner radius 2 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.4.10.099.10.3.10 TS3K
End mills for soft and hard milling, corner radius 1 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.4.10.099.10.3.20 TS3K
End mills for soft and hard milling, corner radius 2 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DST.4.10.119.12.3.20 TS3K
End mills for soft and hard milling, corner radius 2 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 12 mm.
Paul Horn DST.4.12.077.12.3.05 TS3K
End mills for soft and hard milling, corner radius 0.5 mm, 4-edged, with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DST.4.12.077.12.3.20 TS3K
End mills for soft and hard milling, corner radius 2 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DST.4.12.099.12.3.10 TS3K
End mills for soft and hard milling, corner radius 1 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DST.4.12.099.12.3.20 TS3K
End mills for soft and hard milling, corner radius 2 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DST.4.160.20.099.16 TS3K
End mills for soft and hard milling, corner radius 2 mm, 4 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DST.4.160.20.149.16 TS3K
End mills for soft and hard milling, corner radius 2 mm, 4 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DST.4.160.35.099.16 TS3K
End mills for soft and hard milling, corner radius 3.5 mm, 4-edged, with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DST.4.160.35.149.16 TS3K
End mills for soft and hard milling, corner radius 3.5 mm, 4-edged, with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSTC.2.02.02.055.06 TSCC
End mills for processing cobalt-chromium alloys, corner radius 0.2 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSTC.2.02.05.055.06 TSCC
End mills for processing cobalt-chromium alloys, corner radius 0.5 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSTC.2.03.02.055.06 TSCC
End mills for processing cobalt-chromium alloys, corner radius 0.2 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSTC.2.03.05.055.06 TSCC
End mills for processing cobalt-chromium alloys, corner radius 0.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSTC.2.15.01.055.06 TSCC
End mills for processing cobalt-chromium alloys, corner radius 0.1 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm.
Paul Horn DSTC.3.04.02.055.06 TSCC
End mills for processing cobalt-chromium alloys, corner radius 0.2 mm, 3-edged with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTC.3.04.05.055.06 TSCC
End mills for processing cobalt-chromium alloys, corner radius 0.5 mm, 3-edged with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTC.4.05.02.055.06 TSCC
End mills for processing cobalt-chromium alloys, corner radius 0.2 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTC.4.05.05.055.06 TSCC
End mills for processing cobalt-chromium alloys, corner radius 0.5 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTC.4.05.10.055.06 TSCC
End mills for processing cobalt-chromium alloys, corner radius 1 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTC.4.06.02.055.06 TSCC
End mills for processing cobalt-chromium alloys, corner radius 0.2 mm, 4-edged, with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTC.4.06.05.055.06 TSCC
End mills for processing cobalt-chromium alloys, corner radius 0.5 mm, 4-edged, with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTC.4.06.10.055.06 TSCC
End mills for processing cobalt-chromium alloys, corner radius 1 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTC.5.08.02.063.08 TSCC
End mills for processing cobalt-chromium alloys, corner radius 0.2 mm, 5-edged with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTC.5.08.05.063.08 TSCC
End mills for processing cobalt-chromium alloys, corner radius 0.5 mm, 5-edged with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTC.5.08.10.063.08 TSCC
End mills for processing cobalt-chromium alloys, corner radius 1 mm, 5 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTC.5.08.15.063.08 TSCC
End mills for processing cobalt-chromium alloys, corner radius 1.5 mm, 5-edged with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTC.5.10.02.077.10 TSCC
End mills for processing cobalt-chromium alloys, corner radius 0.2 mm, 5-edged with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTC.5.10.05.077.10 TSCC
End mills for processing cobalt-chromium alloys, corner radius 0.5 mm, 5-edged with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTC.5.10.10.077.10 TSCC
End mills for processing cobalt-chromium alloys, corner radius 1 mm, 5 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTC.5.10.15.077.10 TSCC
End mills for processing cobalt-chromium alloys, corner radius 1.5 mm, 5-edged with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTC.5.12.02.077.12 TSCC
End mills for processing cobalt-chromium alloys, corner radius 0.2 mm, 5-edged with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTC.5.12.05.077.12 TSCC
End mills for processing cobalt-chromium alloys, corner radius 0.5 mm, 5-edged with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTC.5.12.10.077.12 TSCC
End mills for processing cobalt-chromium alloys, corner radius 1 mm, 5 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTC.5.12.15.077.12 TSCC
End mills for processing cobalt-chromium alloys, corner radius 1.5 mm, 5-edged with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTC.5.12.20.077.12 TSCC
End mills for processing cobalt-chromium alloys, corner radius 2 mm, 5 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTG.3.02.1.50.04 CD5K
End mills for machining graphite, corner radius 0.1 mm, 3-edged with a diameter of 2 mm and a shaft diameter of 4 mm.
Paul Horn DSTG.3.02.1.63.06 CD5K
End mills for machining graphite, corner radius 0.1 mm, 3-edged with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSTG.3.02.3.50.04 CD5K
End mills for machining graphite, corner radius 0.3 mm, 3-edged with a diameter of 2 mm and a shaft diameter of 4 mm.
Paul Horn DSTG.3.02.3.63.06 CD5K
Torus diamond- coated
Paul Horn DSTG.3.03.1.50.04 CD5K
End mills for machining graphite, corner radius 0.1 mm, 3-edged with a diameter of 3 mm and a shaft diameter of 4 mm.
Paul Horn DSTG.3.03.1.63.06 CD5K
End mills for machining graphite, corner radius 0.1 mm, 3-edged with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSTG.3.03.3.50.04 CD5K
End mills for machining graphite, corner radius 0.3 mm, 3-edged with a diameter of 3 mm and a shaft diameter of 4 mm.
Paul Horn DSTG.3.03.3.63.06 CD5K
End mills for machining graphite, corner radius 0.3 mm, 3-edged with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSTG.3.04.2.63.06 CD5K
End mills for machining graphite, corner radius 0.2 mm, 3-edged with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTG.3.05.2.63.06 CD5K
End mills for machining graphite, corner radius 0.2 mm, 3-fluted, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTG.3.05.5.63.06 CD5K
End mills for machining graphite, corner radius 0.5 mm, 3-fluted, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTG.3.06.10.77.06 CD5K
End mills for machining graphite, corner radius 1 mm, 3-edged with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTG.3.06.3.77.06 CD5K
End mills for machining graphite, corner radius 0.3 mm, 3-edged with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTG.3.06.5.77.06 CD5K
End mills for machining graphite, corner radius 0.5 mm, 3-edged with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTG.3.08.10.77.08 CD5K
Torus diamond- coated
Paul Horn DSTG.3.08.3.77.08 CD5K
End mills for machining graphite, corner radius 0.3 mm, 3-edged with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTG.3.08.5.77.08 CD5K
End mills for machining graphite, corner radius 0.5 mm, 3-edged with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTG.3.10.10.77.10 CD5K
End mills for machining graphite, corner radius 1 mm, 3-edged with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTG.3.10.3.77.10 CD5K
End mills for machining graphite, corner radius 0.3 mm, 3-edged with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTG.3.10.5.77.10 CD5K
End mills for machining graphite, corner radius 0.5 mm, 3-edged with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTG.3.12.10.77.12 CD5K
End mills for machining graphite, corner radius 1 mm, 3-edged with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTG.3.12.3.77.12 CD5K
End mills for machining graphite, corner radius 0.3 mm, 3-edged with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.02.02.055.06 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.02.05.055.06 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.03.05.055.06 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.04.05.055.06 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.040.020.015 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.040.020.030 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.040.020.050 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.040.020.070 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.040.050.015 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.040.050.030 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.040.050.050 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.040.050.070 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.040.100.015 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.040.100.030 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.040.100.050 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.040.100.070 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.05.10.055.06 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.050.020.015 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.050.020.030 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.050.020.050 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.050.020.070 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.050.050.015 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.050.050.030 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.050.050.050 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.050.050.070 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.050.100.015 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.050.100.030 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.050.100.050 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.050.100.070 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.06.02.055.06 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.06.05.055.06 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.06.10.055.06 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.060.020.015 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.060.020.030 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.060.020.050 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.060.020.070 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.060.050.015 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.060.050.030 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.060.050.050 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.060.050.070 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.060.100.015 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.060.100.030 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.060.100.050 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.060.100.070 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.060.200.015 TS3E
End mills for hard machining, corner radius 2 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.060.200.030 TS3E
End mills for hard machining, corner radius 2 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.060.200.050 TS3E
End mills for hard machining, corner radius 2 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.060.200.070 TS3E
End mills for hard machining, corner radius 2 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.2.08.02.063.08 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.08.05.063.08 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.08.10.063.08 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.080.020.015 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.080.020.030 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.080.020.050 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.080.020.070 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.080.050.015 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.080.050.030 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.080.050.050 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.080.050.070 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.080.100.015 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.080.100.030 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.080.100.050 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.080.100.070 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.080.200.015 TS3E
End mills for hard machining, corner radius 2 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.080.200.030 TS3E
End mills for hard machining, corner radius 2 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.080.200.050 TS3E
End mills for hard machining, corner radius 2 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.080.200.070 TS3E
End mills for hard machining, corner radius 2 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.2.10.02.077.10 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.10.05.077.10 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.10.10.077.10 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.10.15.077.10 TS3E
End mills for hard machining, corner radius 1.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.100.020.015 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.100.020.030 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.100.020.050 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.100.020.070 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.100.050.015 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.100.050.030 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.100.050.050 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.100.050.070 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.100.100.015 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.100.100.030 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.100.100.050 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.100.100.070 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.100.200.015 TS3E
End mills for hard machining, corner radius 2 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.100.200.030 TS3E
End mills for hard machining, corner radius 2 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.100.200.050 TS3E
End mills for hard machining, corner radius 2 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.100.200.070 TS3E
End mills for hard machining, corner radius 2 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.2.12.05.077.12 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.12.10.077.12 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.12.15.077.12 TS3E
End mills for hard machining, corner radius 1.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.120.020.015 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.120.020.030 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.120.020.050 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.120.020.070 TS3E
End mills for hard machining, corner radius 0.2 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.120.050.015 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.120.050.030 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.120.050.050 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.120.050.070 TS3E
End mills for hard machining, corner radius 0.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.120.100.015 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.120.100.030 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.120.100.050 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.120.100.070 TS3E
End mills for hard machining, corner radius 1 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.120.200.015 TS3E
End mills for hard machining, corner radius 2 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.120.200.030 TS3E
End mills for hard machining, corner radius 2 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.120.200.050 TS3E
End mills for hard machining, corner radius 2 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.120.200.070 TS3E
End mills for hard machining, corner radius 2 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.2.15.01.055.06 TS3E
End mills for hard machining, corner radius 0.1 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.040.020.015 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.040.020.030 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.040.020.050 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.040.020.070 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.040.050.015 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.040.050.030 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.040.050.050 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.040.050.070 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.040.100.015 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.040.100.030 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.040.100.050 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.040.100.070 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.050.020.015 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.050.020.030 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.050.020.050 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.050.020.070 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.050.050.015 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.050.050.030 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.050.050.050 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.050.050.070 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.050.100.015 TS3E
End mills for hard machining, corner radius 1 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.050.100.030 TS3E
End mills for hard machining, corner radius 1 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.050.100.050 TS3E
End mills for hard machining, corner radius 1 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.050.100.070 TS3E
End mills for hard machining, corner radius 1 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.060.020.015 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.060.020.030 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.060.020.050 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.060.020.070 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.060.050.015 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.060.050.030 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.060.050.050 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.060.050.070 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.060.100.015 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.060.100.030 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.060.100.050 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.060.100.070 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.060.200.015 TS3E
End mills for hard machining, corner radius 2 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.060.200.030 TS3E
End mills for hard machining, corner radius 2 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.060.200.050 TS3E
End mills for hard machining, corner radius 2 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.060.200.070 TS3E
End mills for hard machining, corner radius 2 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTH.4.080.020.015 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.4.080.020.030 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.4.080.020.050 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.4.080.020.070 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.4.080.050.015 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.4.080.050.030 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.4.080.050.050 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.4.080.050.070 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.4.080.100.015 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.4.080.100.030 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.4.080.100.050 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.4.080.100.070 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.4.080.200.015 TS3E
End mills for hard machining, corner radius 2 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.4.080.200.030 TS3E
End mills for hard machining, corner radius 2 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.4.080.200.050 TS3E
End mills for hard machining, corner radius 2 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.4.080.200.070 TS3E
End mills for hard machining, corner radius 2 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTH.4.100.020.015 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.4.100.020.030 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.4.100.020.050 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.4.100.020.070 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.4.100.050.015 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.4.100.050.030 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.4.100.050.050 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.4.100.050.070 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.4.100.100.015 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.4.100.100.030 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.4.100.100.050 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.4.100.100.070 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.4.100.200.015 TS3E
End mills for hard machining, corner radius 2 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.4.100.200.030 TS3E
End mills for hard machining, corner radius 2 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.4.100.200.050 TS3E
End mills for hard machining, corner radius 2 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.4.100.200.070 TS3E
End mills for hard machining, corner radius 2 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTH.4.120.020.015 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.4.120.020.030 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.4.120.020.050 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.4.120.020.070 TS3E
End mills for hard machining, corner radius 0.2 mm, 4-edged, with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.4.120.050.015 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.4.120.050.030 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.4.120.050.050 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.4.120.050.070 TS3E
End mills for hard machining, corner radius 0.5 mm, 4-edged, with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.4.120.100.015 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.4.120.100.030 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.4.120.100.050 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.4.120.100.070 TS3E
End mills for hard machining, corner radius 1 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.4.120.200.015 TS3E
End mills for hard machining, corner radius 2 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.4.120.200.030 TS3E
End mills for hard machining, corner radius 2 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.4.120.200.050 TS3E
End mills for hard machining, corner radius 2 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTH.4.120.200.070 TS3E
End mills for hard machining, corner radius 2 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTK.4.03.05.50.04 CN2K
Torus for processing copper, corner radius 0.5 mm, 4-edged, with a diameter of 3 mm and a shaft diameter of 4 mm.
Paul Horn DSTK.4.03.05.63.06 CN2K
Torus for processing copper, corner radius 0.5 mm, 4-edged, with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSTK.4.05.05.63.06 CN2K
Torus for processing copper, corner radius 0.5 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSTK.4.06.05.63.06 CN2K
Torus for processing copper, corner radius 0.5 mm, 4-edged, with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTK.4.06.10.63.06 CN2K
Torus for processing copper, corner radius 1 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTK.4.08.05.77.08 CN2K
Torus for processing copper, corner radius 0.5 mm, 4-edged, with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTK.4.08.10.77.08 CN2K
Torus for processing copper, corner radius 1 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTK.4.10.05.77.10 CN2K
Torus for processing copper, corner radius 0.5 mm, 4-edged, with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTK.4.10.10.77.10 CN2K
Torus for processing copper, corner radius 1 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTK.4.12.10.88.12 CN2K
Torus for processing copper, corner radius 1 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTK.4.16.10.99.16 CN2K
Torus for processing copper, corner radius 1 mm, 4 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSTLG.2.02.3.099.04 CD5K
End mills for machining graphite, corner radius 0.3 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm.
Paul Horn DSTLG.2.03.3.099.04 CD5K
End mills for machining graphite, corner radius 0.3 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm.
Paul Horn DSTLG.2.04.3.099.06 CD5K
End mills for machining graphite, corner radius 0.3 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSTLG.2.06.5.099.06 CD5K
End mills for machining graphite, corner radius 0.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSTLG.2.08.5.149.08 CD5K
End mills for machining graphite, corner radius 0.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSTLG.2.10.5.149.10 CD5K
End mills for machining graphite, corner radius 0.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSTLG.2.12.5.149.12 CD5K
End mills for machining graphite, corner radius 0.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSTM.2.010.000.030 TS3K
Micro cutters Torus DSTM.2.010.000.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.010.000.050 TS3K
Micro cutters Torus DSTM.2.010.000.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.010.000.070 TS3K
Micro cutters Torus DSTM.2.010.000.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.020.000.030 TS3K
Micro cutters Torus DSTM.2.020.000.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.020.000.050 TS3K
Micro cutters Torus DSTM.2.020.000.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.020.000.070 TS3K
Micro cutters Torus DSTM.2.020.000.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.030.000.030 TS3K
Micro cutters Torus DSTM.2.030.000.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.030.000.050 TS3K
Micro cutters Torus DSTM.2.030.000.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.030.000.070 TS3K
Micro cutters Torus DSTM.2.030.000.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.050.000.030 TS3K
Micro cutters Torus DSTM.2.050.000.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.050.000.050 TS3K
Micro cutters Torus DSTM.2.050.000.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.050.000.070 TS3K
Micro cutters Torus DSTM.2.050.000.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.050.010.030 TS3K
Micro cutters Torus DSTM.2.050.010.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.050.010.050 TS3K
Micro cutters Torus DSTM.2.050.010.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.050.010.070 TS3K
Micro cutters Torus DSTM.2.050.010.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.060.000.030 TS3K
Micro cutters Torus DSTM.2.060.000.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.060.000.050 TS3K
Micro cutters Torus DSTM.2.060.000.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.060.000.070 TS3K
Micro cutters Torus DSTM.2.060.000.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.060.010.030 TS3K
Micro cutters Torus DSTM.2.060.010.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.060.010.050 TS3K
Micro cutters Torus DSTM.2.060.010.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.060.010.070 TS3K
Micro cutters Torus DSTM.2.060.010.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.080.000.030 TS3K
Micro cutters Torus DSTM.2.080.000.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.080.000.050 TS3K
Micro cutters Torus DSTM.2.080.000.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.080.000.070 TS3K
Micro cutters Torus DSTM.2.080.000.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.080.010.030 TS3K
Micro cutters Torus DSTM.2.080.010.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.080.010.050 TS3K
Micro cutters Torus DSTM.2.080.010.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.080.010.070 TS3K
Micro cutters Torus DSTM.2.080.010.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.100.000.030 TS3K
Micro cutters Torus DSTM.2.100.000.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.100.000.050 TS3K
Micro cutters Torus DSTM.2.100.000.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.100.000.070 TS3K
Micro cutters Torus DSTM.2.100.000.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.100.010.030 TS3K
Micro cutters Torus DSTM.2.100.010.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.100.010.050 TS3K
Micro cutters Torus DSTM.2.100.010.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.100.010.070 TS3K
Micro cutters Torus DSTM.2.100.010.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.100.020.030 TS3K
Micro cutters Torus DSTM.2.100.020.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.100.020.050 TS3K
Micro cutters Torus DSTM.2.100.020.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.100.020.070 TS3K
Micro cutters Torus DSTM.2.100.020.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.120.000.030 TS3K
Micro cutters Torus DSTM.2.120.000.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.120.000.050 TS3K
Micro cutters Torus DSTM.2.120.000.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.120.000.070 TS3K
Micro cutters Torus DSTM.2.120.000.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.120.010.030 TS3K
Micro cutters Torus DSTM.2.120.010.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.120.010.050 TS3K
Micro cutters Torus DSTM.2.120.010.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.120.010.070 TS3K
Micro cutters Torus DSTM.2.120.010.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.120.020.030 TS3K
Micro cutters Torus DSTM.2.120.020.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.120.020.050 TS3K
Micro cutters Torus DSTM.2.120.020.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.120.020.070 TS3K
Micro cutters Torus DSTM.2.120.020.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.150.000.030 TS3K
Micro cutters Torus DSTM.2.150.000.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.150.000.050 TS3K
Micro cutters Torus DSTM.2.150.000.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.150.000.070 TS3K
Micro cutters Torus DSTM.2.150.000.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.150.010.030 TS3K
Micro cutters Torus DSTM.2.150.010.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.150.010.050 TS3K
Micro cutters Torus DSTM.2.150.010.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.150.010.070 TS3K
Micro cutters Torus DSTM.2.150.010.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.150.020.030 TS3K
Micro cutters Torus DSTM.2.150.020.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.150.020.050 TS3K
Micro cutters Torus DSTM.2.150.020.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.150.020.070 TS3K
Micro cutters Torus DSTM.2.150.020.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.150.050.030 TS3K
Micro cutters Torus DSTM.2.150.050.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.150.050.050 TS3K
Micro cutters Torus DSTM.2.150.050.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.150.050.070 TS3K
Micro cutters Torus DSTM.2.150.050.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.200.000.030 TS3K
Micro cutters Torus DSTM.2.200.000.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.200.000.050 TS3K
Micro cutters Torus DSTM.2.200.000.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.200.000.070 TS3K
Micro cutters Torus DSTM.2.200.000.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.200.010.030 TS3K
Micro cutters Torus DSTM.2.200.010.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.200.010.050 TS3K
Micro cutters Torus DSTM.2.200.010.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.200.010.070 TS3K
Micro cutters Torus DSTM.2.200.010.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.200.020.030 TS3K
Micro cutters Torus DSTM.2.200.020.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.200.020.050 TS3K
Micro cutters Torus DSTM.2.200.020.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.200.020.070 TS3K
Micro cutters Torus DSTM.2.200.020.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.200.050.030 TS3K
Micro cutters Torus DSTM.2.200.050.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.200.050.050 TS3K
Micro cutters Torus DSTM.2.200.050.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.200.050.070 TS3K
Micro cutters Torus DSTM.2.200.050.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.250.000.030 TS3K
Micro cutters Torus DSTM.2.250.000.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.250.000.050 TS3K
Micro cutters Torus DSTM.2.250.000.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.250.000.070 TS3K
Micro cutters Torus DSTM.2.250.000.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.250.010.030 TS3K
Micro cutters Torus DSTM.2.250.010.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.250.010.050 TS3K
Micro cutters Torus DSTM.2.250.010.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.250.010.070 TS3K
Micro cutters Torus DSTM.2.250.010.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.250.020.030 TS3K
Micro cutters Torus DSTM.2.250.020.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.250.020.050 TS3K
Micro cutters Torus DSTM.2.250.020.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.250.020.070 TS3K
Micro cutters Torus DSTM.2.250.020.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.250.050.030 TS3K
Micro cutters Torus DSTM.2.250.050.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.250.050.050 TS3K
Micro cutters Torus DSTM.2.250.050.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.250.050.070 TS3K
Micro cutters Torus DSTM.2.250.050.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.300.000.030 TS3K
Micro cutters Torus DSTM.2.300.000.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.300.000.050 TS3K
Micro cutters Torus DSTM.2.300.000.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.300.000.070 TS3K
Micro cutters Torus DSTM.2.300.000.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.300.010.030 TS3K
Micro cutters Torus DSTM.2.300.010.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.300.010.050 TS3K
Micro cutters Torus DSTM.2.300.010.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.300.010.070 TS3K
Micro cutters Torus DSTM.2.300.010.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.300.020.030 TS3K
Micro cutters Torus DSTM.2.300.020.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.300.020.050 TS3K
Micro cutters Torus DSTM.2.300.020.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.300.020.070 TS3K
Micro cutters Torus DSTM.2.300.020.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.300.050.030 TS3K
Micro cutters Torus DSTM.2.300.050.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.300.050.050 TS3K
Micro cutters Torus DSTM.2.300.050.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.300.050.070 TS3K
Micro cutters Torus DSTM.2.300.050.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.300.100.030 TS3K
Micro cutters Torus DSTM.2.300.100.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.300.100.050 TS3K
Micro cutters Torus DSTM.2.300.100.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.2.300.100.070 TS3K
Micro cutters Torus DSTM.2.300.100.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSTM.4.020.000.030 TS3K
Micro cutters Torus DSTM.4.020.000.030, 4-edged, 30 В° helix angle, center cutting
Paul Horn DSTM.4.020.000.050 TS3K
Micro cutters Torus DSTM.4.020.000.050, 4-edged, 30 В° helix angle, center cutting
Paul Horn DSTM.4.020.000.070 TS3K
Micro cutters Torus DSTM.4.020.000.070, 4-edged, 30 В° helix angle, center cutting
Paul Horn DSTM.4.030.000.030 TS3K
Micro cutters Torus DSTM.4.030.000.030, 4-edged, 30 В° helix angle, center cutting
Paul Horn DSTM.4.030.000.050 TS3K
Micro cutters Torus DSTM.4.030.000.050, 4-edged, 30 В° helix angle, center cutting
Paul Horn DSTM.4.030.000.070 TS3K
Micro cutters Torus DSTM.4.030.000.070, 4-edged, 30 В° helix angle, center cutting
Paul Horn DSTM.4.050.000.030 TS3K
Micro cutters Torus DSTM.4.050.000.030, 4-edged, 30 В° helix angle, center cutting
Paul Horn DSTM.4.050.000.050 TS3K
Micro cutters Torus DSTM.4.050.000.050, 4-edged, 30 В° helix angle, center cutting
Paul Horn DSTM.4.050.000.070 TS3K
Micro cutters Torus DSTM.4.050.000.070, 4-edged, 30 В° helix angle, center cutting
Paul Horn DSTM.4.050.010.030 TS3K
Micro cutters Torus DSTM.4.050.010.030, 4-edged, 30 В° helix angle, center cutting
Paul Horn DSTM.4.050.010.050 TS3K
Micro cutters Torus DSTM.4.050.010.050, 4-edged, 30 В° helix angle, center cutting
Paul Horn DSTM.4.050.010.070 TS3K
Micro cutters Torus DSTM.4.050.010.070, 4-edged, 30 В° helix angle, center cutting
Paul Horn DSTM.4.060.000.030 TS3K
Micro cutters Torus DSTM.4.060.000.030, 4-edged, 30 В° helix angle, center cutting
Paul Horn DSTM.4.060.000.050 TS3K
Micro cutters Torus DSTM.4.060.000.050, 4-edged, 30 В° helix angle, center cutting
Paul Horn DSTM.4.060.000.070 TS3K
Micro cutters Torus DSTM.4.060.000.070, 4-edged, 30 В° helix angle, center cutting
Paul Horn DSTM.4.060.010.030 TS3K
Micro cutters Torus DSTM.4.060.010.030, 4-edged, 30 В° helix angle, center cutting
Paul Horn DSTM.4.060.010.050 TS3K
Micro cutters Torus DSTM.4.060.010.050, 4-edged, 30 В° helix angle, center cutting
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 ... 30