Paul Horn запчасти (311.0130.00 TN35

Paul Horn 311.0130.00 TN35
The insert with a cutting diameter of 17.7 mm and a cutting width of 1.41 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0130.40 TI25
The insert with a cutting diameter of 17.7 mm and a cutting width of 1.41 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0150.00 AS45
The insert with a cutting diameter of 17.7 mm and a cutting width of 1.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0150.00 TN35
The insert with a cutting diameter of 17.7 mm and a cutting width of 1.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0150.40 TI25
The insert with a cutting diameter of 17.7 mm and a cutting width of 1.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0160.00 AS45
The insert with a cutting diameter of 17.7 mm and a cutting width of 1.71 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0160.00 TN35
The insert with a cutting diameter of 17.7 mm and a cutting width of 1.71 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0160.40 TI25
The insert with a cutting diameter of 17.7 mm and a cutting width of 1.71 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0200.00 AS45
The insert with a cutting diameter of 17.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0200.00 MG12
The insert with a cutting diameter of 17.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0200.00 TN35
The insert with a cutting diameter of 17.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0200.40 TI25
The insert with a cutting diameter of 17.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0250.00 AS45
The insert with a cutting diameter of 17.7 mm and a cutting width of 2.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0250.00 TN35
The insert with a cutting diameter of 17.7 mm and a cutting width of 2.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0250.40 TI25
The insert with a cutting diameter of 17.7 mm and a cutting width of 2.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0300.00 AS45
The insert with a cutting diameter of 17.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0300.00 MG12
The insert with a cutting diameter of 17.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0300.00 TN35
The insert with a cutting diameter of 17.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0300.40 TI25
The insert with a cutting diameter of 17.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0400.00 AS45
The insert with a cutting diameter of 17.7 mm and a cutting width of 4 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0400.40 TI25
The insert with a cutting diameter of 17.7 mm and a cutting width of 4 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 3.5 mm deep.

Paul Horn 311.0510.01 TN35
Insert with a pitch range of 1.0 mm or 24 - 32 transition / inch and a cutting circle diameter of 17.70 mm is suitable for producing internal threads in partial profile.

Paul Horn 311.0515.01 TA45
Insert with a pitch range of 0.5 -1.5 mm or 18 - 48 transition / inch and a cutting circle diameter of 17.70 mm is suitable for producing internal threads in partial profile.

Paul Horn 311.0720.01 TN35
Insert with a pitch range of 1.0 - 2.0 mm or 12-32 transition / inch and a cutting circle diameter of 17.70 mm is suitable for producing internal threads in partial profile.

Paul Horn 311.0815.01 TN35
Insert with a pitch range of 1.5 mm or 16-20 transition / inch and a cutting circle diameter of 17.70 mm is suitable for producing internal threads in partial profile.

Paul Horn 311.0815.02 TN35
The insert full profile and a cutting circle diameter of 17.70 mm is suitable for thread milling metric threads with a pitch of 1.50 mm.

Paul Horn 311.0917.02 TN35
The insert full profile and a cutting circle diameter of 17.70 mm is suitable for thread milling metric threads with a pitch of 1.75 mm.

Paul Horn 311.1016.00 AS45
The insert with a cutting diameter of 17 mm and a cutting width of 7.2 mm is suitable for T-slot milling of internal and external contours.

Paul Horn 311.1016.00 TI25
The insert with a cutting diameter of 17 mm and a cutting width of 7.2 mm is suitable for T-slot milling of internal and external contours.

Paul Horn 311.1020.01 TN35
Insert with a pitch range of 2.0 mm or 14-16 transition / inch and a cutting circle diameter of 17.70 mm is suitable for producing internal threads in partial profile.

Paul Horn 311.1020.02 TN35
The insert full profile and a cutting circle diameter of 17.70 mm is suitable for thread milling metric threads with a pitch of 2.00 mm.

Paul Horn 311.1325.01 TN35
Insert with a pitch range of 2.5 mm or 11 - 12 transition / inch and a cutting circle diameter of 17.70 mm is suitable for producing internal threads in partial profile.

Paul Horn 311.1325.02 TN35
The insert full profile and a cutting circle diameter of 17.70 mm is suitable for thread milling metric threads with a gradient of 2:50 mm.

Paul Horn 311.1630.01 TN35
Insert with a pitch range of 3.0 mm or 8 - 9 gear / inch and a cutting circle diameter of 17.70 mm is suitable for producing internal threads in partial profile.

Paul Horn 311.1630.02 TN35
The insert full profile and a cutting circle diameter of 17.70 mm is suitable for thread milling metric threads with a pitch of 3.00 mm.

Paul Horn 311.1835.01 TN35
Insert with a pitch range of 3.5 mm or 7 - 8 Gang / inch and a cutting circle diameter of 17.70 mm is suitable for producing internal threads in partial profile.

Paul Horn 311.1835.02 TN35
The insert full profile and a cutting circle diameter of 17.70 mm is suitable for thread milling metric threads with a pitch of 3.50 mm.

Paul Horn 311.2535.01 TN35
Insert with a pitch range of 2.5 - 3.5 mm or 6 - 8 Gang / inch and a cutting circle diameter of 17.70 mm is suitable for producing internal threads in partial profile.

Paul Horn 311.4216.00 TI25
The insert with a cutting diameter of 15.8 mm is suitable for T-slot chamfering of inner and outer contours.

Paul Horn 311.4545.00 TN35
The insert with a cutting diameter of 17.7 mm and a cutting width of 2.5 mm is suitable for bore milling and chamfering of inner and outer contours with up to 1.4 mm deep.

Paul Horn 311.4545.20 TI25
The insert with a cutting diameter of 15 mm and a cutting width of 0.2 mm is suitable for bore milling and chamfering of inner and outer contours with depths up to 2.5 mm.

Paul Horn 311.4545.20 TN35
Insert with a cutting width of 0.2 mm and a cutting diameter of 15 mm is suitable for chamfering with 45 В° of grooves on the inner and outer contours with maximum chamfer length of 2.5 mm.

Paul Horn 311.5511.02 TA45
The insert with full profile and a cutting circle diameter of 17.70 mm is suitable for thread milling of Whitworth pipe threads with a pitch of 11 Gg / inch.

Paul Horn 311.5511.02 TI25
The insert with full profile and a cutting circle diameter of 17.70 mm is suitable for thread milling of Whitworth pipe threads with a pitch of 11 Gg / inch.

Paul Horn 311.5511.02 TN35
The insert full profile and a cutting circle diameter of 17.70 mm is suitable for thread milling of Whitworth pipe threads with a pitch of 11 Gg / inch.

Paul Horn 311.5514.02 TA45
The insert with full profile and a cutting circle diameter of 17.70 mm is suitable for thread milling of Whitworth pipe threads with a pitch of 14 Gg / inch.

Paul Horn 311.5514.02 TI25
The insert with full profile and a cutting circle diameter of 17.70 mm is suitable for thread milling of Whitworth pipe threads with a pitch of 14 Gg / inch.

Paul Horn 311.5514.02 TN35
The insert full profile and a cutting circle diameter of 17.70 mm is suitable for thread milling of Whitworth pipe threads with a pitch of 14 Gg / inch.

Paul Horn 312.0010.20 K10
The indexable insert with radius and a cutting width of 2 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0010.20 P20
The indexable insert with full radius and a cutting width of 2 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0010.20 TC92
The indexable insert with radius and a cutting width of 2 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0010.20 TN32
The indexable insert with radius and a cutting width of 2 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0010.20 TN35
The indexable insert with radius and a cutting width of 2 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0012.V1 TF45
The indexable insert with a cutting width of 1.2 mm is suitable for tapping inner and outer contours with up to 8 mm depth.

Paul Horn 312.0015.30 K10
The indexable insert with radius and a cutting width of 3 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0015.30 P20
The indexable insert with full radius and a cutting width of 3 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0015.30 TC92
The indexable insert with radius and a cutting width of 3 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0015.30 TN32
The indexable insert with radius and a cutting width of 3 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0015.V1 TF45
The indexable insert with a cutting width of 1.5 mm is suitable for tapping inner and outer contours with up to 8 mm depth.

Paul Horn 312.0020.40 K10
The indexable insert with radius and a cutting width of 4 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0020.40 P20
The indexable insert with full radius and a cutting width of 4 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0020.40 TC92
The indexable insert with radius and a cutting width of 4 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0020.40 TN32
The indexable insert with radius and a cutting width of 4 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0025.50 K10
The indexable insert with radius and a cutting width of 5 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0025.50 P20
The indexable insert with full radius and a cutting width of 5 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0025.50 TC92
The indexable insert with radius and a cutting width of 5 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0025.50 TN32
The indexable insert with radius and a cutting width of 5 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0050.00 K10
The indexable insert with a cutting width of 0.57 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0050.00 P20
The indexable insert with a cutting width of 0.57 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0050.00 TF45
The indexable insert with a cutting width of 0.57 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0050.00 TN32
The indexable insert with a cutting width of 0.57 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0050.02 P20
The indexable insert with a cutting width of 0.5 mm is suitable for grooving and profile turning of internal and external contours with up to 6 mm depth.

Paul Horn 312.0050.02 TN32
The indexable insert with a cutting width of 0.5 mm is suitable for grooving and profile turning of internal and external contours with up to 6 mm depth.

Paul Horn 312.0050.15 TN32
The indexable insert with a cutting width of 0.57 mm is suitable for grooving of the inner and outer contours with up to 0.7 mm deep.

Paul Horn 312.0060.00 K10
The indexable insert with a cutting width of 0.67 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0060.00 P20
Indexable insert with a cutting width of 0.67 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 0.6 mm).

Paul Horn 312.0060.00 TF45
Indexable insert with a cutting width of 0.67 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 0.6 mm).

Paul Horn 312.0060.00 TF46
Indexable insert with a cutting width of 0.67 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 0.6 mm).

Paul Horn 312.0060.00 TN32
The indexable insert with a cutting width of 0.67 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0060.15 TN32
The indexable insert with a cutting width of 0.67 mm is suitable for grooving of the inner and outer contours with up to 0.8 mm deep.

Paul Horn 312.0070.00 K10
The indexable insert with a cutting width of 0.77 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0070.00 P20
Indexable insert with a cutting width of 0.77 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 0.7 mm).

Paul Horn 312.0070.00 TF45
The indexable insert with a cutting width of 0.77 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0070.00 TF46
Indexable insert with a cutting width of 0.77 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 0.7 mm).

Paul Horn 312.0070.00 TN32
The indexable insert with a cutting width of 0.77 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0070.15 TN32
The indexable insert with a cutting width of 0.77 mm is suitable for grooving of the inner and outer contours with up to 1.1 mm deep.

Paul Horn 312.0080.00 K10
The indexable insert with a cutting width of 0.87 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0080.00 P20
Indexable insert with a cutting width of 0.87 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 0.8 mm).

Paul Horn 312.0080.00 TF45
Indexable insert with a cutting width of 0.87 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 0.8 mm).

Paul Horn 312.0080.00 TF46
The indexable insert with a cutting width of 0.87 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0080.00 TN32
Indexable insert with a cutting width of 0.87 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 0.8 mm).

Paul Horn 312.0080.15 TN32
The indexable insert with a cutting width of 0.87 mm is suitable for grooving of the inner and outer contours with up to 1.2 mm deep.

Paul Horn 312.0090.00 K10
The indexable insert with a cutting width of 0.97 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0090.00 P20
The indexable insert with a cutting width of 0.97 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0090.00 TF45
The indexable insert with a cutting width of 0.97 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0090.00 TF46
Indexable insert with a cutting width of 0.97 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 0.9 mm).

Paul Horn 312.0090.00 TN32
The indexable insert with a cutting width of 0.97 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0090.00 TN35
The indexable insert with a cutting width of 0.97 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0090.15 TN32
The indexable insert with a cutting width of 0.97 mm is suitable for grooving of the inner and outer contours with up to 1.4 mm deep.

Paul Horn 312.0100.00 K10
The indexable insert with a cutting width of 1.07 mm is suitable for tapping inner and outer contours with up to 8 mm depth.

Paul Horn 312.0100.00 P20
The indexable insert with a cutting width of 1.07 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0100.00 TF45
The indexable insert with a cutting width of 1.07 mm is suitable for tapping inner and outer contours with up to 8 mm depth.

Paul Horn 312.0100.00 TF46
The indexable insert with a cutting width of 1.07 mm is suitable for grooving and turning of internal and external contours with up to 8 mm depth.

Paul Horn 312.0100.00 TN32
The indexable insert with a cutting width of 1.07 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0100.00 TN35
The indexable insert with a cutting width of 1.07 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0100.02 TI25
The indexable insert with a cutting width of 1 mm is suitable for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0100.02 TN32
Indexable insert with a cutting width of 1 mm and maximum cutting depth of 6 mm is suitable for grooving grooves on inner and outer contours.

Paul Horn 312.0100.05 AS45
The indexable insert with a cutting width of 1 mm is suitable for grooving and profile turning of internal and external contours with up to 6 mm depth.

Paul Horn 312.0100.05 P20
The indexable insert with a cutting width of 1 mm is suitable for grooving and profile turning of internal and external contours with up to 6 mm depth.

Paul Horn 312.0100.05 TN32
The indexable insert with a cutting width of 1 mm is suitable for grooving and profile turning of internal and external contours with up to 6 mm depth.

Paul Horn 312.0100.15 TN32
The indexable insert with a cutting width of 1.07 mm is suitable for grooving of the inner and outer contours with up to 1.6 mm deep.

Paul Horn 312.0110.00 K10
The indexable insert with a cutting width of 1.24 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0110.00 P20
The indexable insert with a cutting width of 1.24 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0110.00 TC92
The indexable insert with a cutting width of 1.24 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0110.00 TF45
The indexable insert with a cutting width of 1.24 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0110.00 TF46
The indexable insert with a cutting width of 1.24 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0110.00 TN32
The indexable insert with a cutting width of 1.24 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0110.05 AS45
Indexable insert with a cutting width of 1.1 mm and maximum cutting depth of 6 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 0 mm).

Paul Horn 312.0110.80 TN35
The indexable insert with a cutting width of 1.24 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0120.06 AS45
The indexable insert with a cutting width of 1.2 mm is suitable for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0120.06 P20
The indexable insert with a cutting width of 1.2 mm is suitable for grooving and profile turning of internal and external contours with up to 6 mm depth.

Paul Horn 312.0120.06 TN32
The indexable insert with a cutting width of 1.2 mm is suitable for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0130.00 K10
The indexable insert with a cutting width of 1.44 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0130.00 P20
The indexable insert with a cutting width of 1.44 mm is suitable for tapping inner and outer contours with up to 8 mm depth.

Paul Horn 312.0130.00 TC92
The indexable insert with a cutting width of 1.44 mm is suitable for tapping inner and outer contours with up to 8 mm depth.

Paul Horn 312.0130.00 TF45
The indexable insert with a cutting width of 1.44 mm is suitable for tapping inner and outer contours with up to 8 mm depth.

Paul Horn 312.0130.00 TF46
The indexable insert with a cutting width of 1.44 mm is suitable for tapping inner and outer contours with up to 8 mm depth.

Paul Horn 312.0130.00 TN32
The indexable insert with a cutting width of 1.44 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0130.00 TN35
The indexable insert with a cutting width of 1.44 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0130.80 TN35
The indexable insert with a cutting width of 1.44 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0140.07 AS45
Indexable insert with a cutting width of 1.4 mm (full radius 0.7 mm) and maximum penetration depth of 6 mm is suitable for grooving grooves on inner and outer contours.

Paul Horn 312.0150.02 P20
The indexable insert with a cutting width of 1.5 mm is suitable for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0150.02 TI25
The indexable insert with a cutting width of 1.5 mm is suitable for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0150.02 TN32
The indexable insert with a cutting width of 1.5 mm is suitable for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0150.02 TN35
The indexable insert with a cutting width of 1.5 mm is suitable for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0160.00 K10
The indexable insert with a cutting width of 1.74 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0160.00 P20
The indexable insert with a cutting width of 1.74 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0160.00 TC92
The indexable insert with a cutting width of 1.74 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0160.00 TF45
The indexable insert with a cutting width of 1.74 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0160.00 TF46
The indexable insert with a cutting width of 1.74 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0160.00 TN32
The indexable insert with a cutting width of 1.74 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0160.00 TN35
The indexable insert with a cutting width of 1.74 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0160.08 AS45
The indexable insert with a cutting width of 1.6 mm is suitable for grooving of the inner and outer contours of up to 6 mm depth.

Paul Horn 312.0160.08 P20
The indexable insert with a cutting width of 1.6 mm is suitable for grooving and profile turning of internal and external contours with up to 6 mm depth.

Paul Horn 312.0160.08 TN32
The indexable insert with a cutting width of 1.6 mm is suitable for grooving of the inner and outer contours of up to 6 mm depth.

Paul Horn 312.0160.80 TN35
The indexable insert with a cutting width of 1.74 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0180.09 AS45
Indexable insert with a cutting width of 1.8 mm (full radius 0.9 mm) and maximum penetration depth of 6 mm is suitable for grooving grooves on inner and outer contours.

Paul Horn 312.0185.00 H20
The indexable insert with a cutting width of 1.99 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0185.00 K10
The indexable insert with a cutting width of 1.99 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0185.00 MG12
The indexable insert with a cutting width of 1.99 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0185.00 P20
The indexable insert with a cutting width of 1.99 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0185.00 TC92
The indexable insert with a cutting width of 1.99 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0185.00 TF45
The indexable insert with a cutting width of 1.99 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0185.00 TF46
The indexable insert with a cutting width of 1.99 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0185.00 TI25
The indexable insert with a cutting width of 1.99 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0185.00 TN32
The indexable insert with a cutting width of 1.99 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0185.00 TN35
The indexable insert with a cutting width of 1.99 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0185.10 K10
The indexable insert with a cutting width of 1.99 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0185.10 P20
The indexable insert with a cutting width of 1.99 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0185.80 TN35
The indexable insert with a cutting width of 1.99 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0200.02 H20
The indexable insert with a cutting width of 2 mm is good for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0200.02 K10
The indexable insert with a cutting width of 2 mm is good for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0200.02 P20
The indexable insert with a cutting width of 2 mm is good for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0200.02 TF45
The indexable insert with a cutting width of 2 mm is good for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0200.02 TI22
The indexable insert 312.0200.02 Ti22 with a cutting width of 2 mm is good for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0200.02 TI25
The indexable insert with a cutting width of 2 mm is good for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0200.02 TN32
The indexable insert with a cutting width of 2 mm is good for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0200.02 TN35
The indexable insert with a cutting width of 2 mm is good for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0200.04 AS62
Indexable insert with a cutting width of 2 mm and maximum cutting depth of 6 mm is suitable for grooving grooves on inner and outer contours.

Paul Horn 312.0200.04 H20
The indexable insert with a cutting width of 2 mm is good for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0200.04 P20
Indexable insert with a cutting width of 2 mm and maximum cutting depth of 6 mm is suitable for grooving grooves on inner and outer contours.

Paul Horn 312.0200.04 TN32
The indexable insert with a cutting width of 2 mm is good for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0200.10 AS45
The indexable insert with a cutting width of 2 mm is suitable for grooving and profile turning of internal and external contours with up to 6 mm depth.

Paul Horn 312.0200.10 P20
The indexable insert with a cutting width of 2 mm is suitable for grooving and profile turning of internal and external contours with up to 6 mm depth.

Paul Horn 312.0200.10 TN32
The indexable insert with a cutting width of 2 mm is suitable for grooving and profile turning of internal and external contours with up to 6 mm depth.

Paul Horn 312.0215.00 H20
The indexable insert with a cutting width of 2.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0215.00 K10
The indexable insert with a cutting width of 2.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0215.00 MG12
The indexable insert with a cutting width of 2.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0215.00 P20
The indexable insert with a cutting width of 2.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0215.00 TA45
The indexable insert with a cutting width of 2.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0215.00 TC92
The indexable insert with a cutting width of 2.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0215.00 TF45
The indexable insert with a cutting width of 2.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0215.00 TF46
The indexable insert with a cutting width of 2.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0215.00 TN32
The indexable insert with a cutting width of 2.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0215.00 TN35
The indexable insert with a cutting width of 2.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0215.10 K10
The indexable insert with a cutting width of 2.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0215.10 P20
The indexable insert with a cutting width of 2.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0215.80 TN35
The indexable insert with a cutting width of 2.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0220.11 AS45
Indexable insert with a cutting width of 2.2 mm (Full Radius 1:10 mm) and maximum penetration depth of 6 mm is suitable for grooving grooves on inner and outer contours.

Paul Horn 312.0223.30 P20
The indexable insert is suitable for grooving of outer contours with up to 2:34 mm depth.

Paul Horn 312.0223.30 TN32
Indexable insert with a flank angle of 20 В° and maximum cutting depth of 2:34 mm is suitable for grooving grooves suitable for poly-V-belt pulleys.

Paul Horn 312.0250.12 AS45
Indexable insert with a cutting width of 2.5 mm (full radius 1.25mm) and maximum penetration depth of 6 mm is suitable for grooving grooves on inner and outer contours.

Paul Horn 312.0250.12 P20
The indexable insert with a cutting width of 2.5 mm is suitable for grooving and profile turning of internal and external contours with up to 6 mm depth.

Paul Horn 312.0250.12 TN32
Indexable insert with a cutting width of 2.5 mm (full radius 1.25mm) and maximum penetration depth of 6 mm is suitable for grooving grooves on inner and outer contours.

Paul Horn 312.0265.00 H20
The indexable insert with a cutting width of 2.79 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0265.00 K10
Indexable insert with a cutting width of 2.79 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 2.65 mm).

Paul Horn 312.0265.00 MG12
Indexable insert with a cutting width of 2.79 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 2.65 mm).

Paul Horn 312.0265.00 P20
Indexable insert with a cutting width of 2.79 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 2.65 mm).

Paul Horn 312.0265.00 TC92
The indexable insert with a cutting width of 2.79 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0265.00 TF45
The indexable insert with a cutting width of 2.79 mm is suitable for grooving and turning of internal and external contours with up to 8 mm depth.

Paul Horn 312.0265.00 TF46
The indexable insert with a cutting width of 2.79 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0265.00 TN32
The indexable insert with a cutting width of 2.79 mm is suitable for grooving and turning of internal and external contours with up to 8 mm depth.

Paul Horn 312.0265.00 TN35
The indexable insert with a cutting width of 2.79 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0265.10 K10
The indexable insert with a cutting width of 2.79 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0265.10 P20
The indexable insert with a cutting width of 2.79 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0265.80 TN35
The indexable insert with a cutting width of 2.79 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0280.14 AS45
Indexable insert with a cutting width of 2.8 mm (full radius 1.4 mm) and maximum penetration depth of 6 mm is suitable for grooving grooves on inner and outer contours.

Paul Horn 312.0300.02 H20
The indexable insert with a cutting width of 3 mm is suitable for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0300.02 P20
The indexable insert with a cutting width of 3 mm is suitable for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0300.02 TI25
The indexable insert with a cutting width of 3 mm is suitable for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0300.02 TN32
The indexable insert with a cutting width of 3 mm is suitable for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0300.06 P20
The indexable insert with a cutting width of 3 mm is suitable for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0300.06 TN32
Indexable insert with a cutting width of 3 mm and maximum cutting depth of 6 mm is suitable for grooving grooves on inner and outer contours.

Paul Horn 312.0300.08 P20
The indexable insert with a cutting width of 3 mm is suitable for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0300.08 TN32
Indexable insert with a cutting width of 3 mm and maximum cutting depth of 6 mm is suitable for grooving grooves on inner and outer contours.

Paul Horn 312.0300.15 AS45
The indexable insert with a cutting width of 3 mm is suitable for grooving of the inner and outer contours of up to 6 mm depth.

Paul Horn 312.0300.15 P20
The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 6 mm depth.

Paul Horn 312.0300.15 TN32
The indexable insert with a cutting width of 3 mm is suitable for grooving of the inner and outer contours of up to 6 mm depth.

Paul Horn 312.0315.00 H20
The indexable insert with a cutting width of 3.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0315.00 K10
The indexable insert with a cutting width of 3.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0315.00 P20
The indexable insert with a cutting width of 3.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0315.00 TC92
The indexable insert with a cutting width of 3.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0315.00 TF45
The indexable insert with a cutting width of 3.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0315.00 TF46
The indexable insert with a cutting width of 3.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0315.00 TN32
The indexable insert with a cutting width of 3.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0315.00 TN35
The indexable insert with a cutting width of 3.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0315.10 K10
The indexable insert with a cutting width of 3.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0315.10 P20
The indexable insert with a cutting width of 3.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0315.80 TN35
The indexable insert with a cutting width of 3.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0360.18 AS45
Indexable insert with a cutting width of 3.6 mm (full radius 1.80 mm) and maximum penetration depth of 6 mm is suitable for grooving grooves on inner and outer contours.

Paul Horn 312.0400.02 H20
The indexable insert with a cutting width of 4 mm is suitable for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0400.02 P20
The indexable insert with a cutting width of 4 mm is suitable for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0400.02 TN32
Indexable insert with a cutting width of 4 mm and maximum cutting depth of 6 mm is suitable for grooving grooves on inner and outer contours.

Paul Horn 312.0400.08 P20
Indexable insert uncoated

Paul Horn 312.0400.08 TN32
The indexable insert with a cutting width of 4 mm is suitable for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0400.12 P20
The indexable insert with a cutting width of 4 mm is suitable for copying inner and outer contours of up to 6 mm depth.

Paul Horn 312.0400.20 AS45
Indexable insert with a cutting width of 4 mm (full radius 2 mm) and maximum penetration depth of 6 mm is suitable for grooving grooves on inner and outer contours.

Paul Horn 312.0400.20 P20
The indexable insert with a cutting width of 4 mm is suitable for grooving and profile turning of internal and external contours with up to 6 mm depth.

Paul Horn 312.0400.20 TN32
Indexable insert with a cutting width of 4 mm (full radius 2 mm) and maximum penetration depth of 6 mm is suitable for grooving grooves on inner and outer contours.

Paul Horn 312.0415.00 K10
The indexable insert with a cutting width of 4.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0415.00 P20
Indexable insert with a cutting width of 4.29 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (nominal width 4.15 mm).

Paul Horn 312.0415.00 TC92
Indexable insert with a cutting width of 4.29 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 4.15 mm).

Paul Horn 312.0415.00 TF45
Indexable insert with a cutting width of 4.29 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (nominal width 4.15 mm).

Paul Horn 312.0415.00 TF46
Indexable insert with a cutting width of 4.29 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (nominal width 4.15 mm).

Paul Horn 312.0415.00 TN32
Indexable insert with a cutting width of 4.29 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (nominal width 4.15 mm).

Paul Horn 312.0415.00 TN35
Indexable insert with a cutting width of 4.29 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (nominal width 4.15 mm).

Paul Horn 312.0415.10 K10
The indexable insert with a cutting width of 4.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0415.10 P20
The indexable insert with a cutting width of 4.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0415.80 TN35
The indexable insert with a cutting width of 4.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0515.00 H20
The indexable insert with a cutting width of 5.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0515.00 K10
Indexable insert with a cutting width of 5.29 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 5.15 mm).

Paul Horn 312.0515.00 P20
Indexable insert with a cutting width of 5.29 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (nominal width 5.15 mm).

Paul Horn 312.0515.00 TF45
The indexable insert with a cutting width of 5.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0515.00 TF46
Indexable insert with a cutting width of 5.29 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (nominal width 5.15 mm).

Paul Horn 312.0515.00 TN32
Indexable insert with a cutting width of 5.29 mm and maximum cutting depth of 8 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (nominal width 5.15 mm).

Paul Horn 312.0515.10 K10
The indexable insert with a cutting width of 5.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0515.10 P20
The indexable insert with a cutting width of 5.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0515.80 TN35
The indexable insert with a cutting width of 5.29 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth.

Paul Horn 312.0602.24 AS62
Indexable insert with a radius of 0.6 mm is suitable for the manufacture of corner undercuts on the inner and outer contours.

Paul Horn 312.0602.24 P20
The indexable insert is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0602.24 TC92
The indexable insert is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.0603.33 P20
The indexable insert with a cutting width of 3.3 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.1002.30 P20
The indexable insert with a cutting width of 3 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.1004.50 P20
The indexable insert with a cutting width of 5 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.1101.25 TN32
The indexable insert with a cutting width of 1.24 mm is suitable for grooving of the inner and outer contours with up to 0.2 mm in depth and NutauГџenkantenfasung.

Paul Horn 312.1102.25 TN32
The indexable insert with a cutting width of 1.24 mm is suitable for grooving of the inner and outer contours with up to 0.25mm deep and NutauГџenkantenfasung.

Paul Horn 312.1103.25 TN32
The indexable insert with a cutting width of 1.24 mm is suitable for grooving of the inner and outer contours with up to 0.3 mm in depth and NutauГџenkantenfasung.

Paul Horn 312.1104.25 TN32
The indexable insert with a cutting width of 1.24 mm is suitable for grooving of the inner and outer contours with up to 0.35mm deep and NutauГџenkantenfasung.

Paul Horn 312.1105.25 P20
The indexable insert with a cutting width of 1.24 mm is suitable for grooving of the inner and outer contours with up to 0.4 mm in depth and NutauГџenkantenfasung.

Paul Horn 312.1105.25 TN32
Indexable insert with a cutting width of 1.24 mm and maximum cutting depth of 0.4 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 1.1 mm) with NutauГџenkantenfasung.

Paul Horn 312.1306.25 TN32
The indexable insert with a cutting width of 1.44 mm is suitable for grooving of the inner and outer contours with up to 0.55mm deep and NutauГџenkantenfasung.

Paul Horn 312.1603.50 P20
The indexable insert with a cutting width of 5 mm is suitable for corner undercutting of inner and outer contours.

Paul Horn 312.1607.33 TN32
The indexable insert with a cutting width of 1.74 mm is suitable for grooving of the inner and outer contours with up to 0.7 mm in depth and NutauГџenkantenfasung.

Paul Horn 312.1608.33 TN32
The indexable insert with a cutting width of 1.74 mm is suitable for grooving of the inner and outer contours of up to 0.85 mm depth and NutauГџenkantenfasung.

Paul Horn 312.1609.33 TN32
The indexable insert with a cutting width of 1.74 mm is suitable for grooving of the inner and outer contours with up to 1 mm depth and NutauГџenkantenfasung.

Paul Horn 312.1810.33 TN32
The indexable insert with a cutting width of 1.99 mm is suitable for grooving of the inner and outer contours with up to 1 mm depth and NutauГџenkantenfasung.

Paul Horn 312.1812.33 TN32
The indexable insert with a cutting width of 1.99 mm is suitable for grooving of the inner and outer contours with up to 1.25mm deep and NutauГџenkantenfasung.

Paul Horn 312.2115.43 P20
The indexable insert with a cutting width of 2.29 mm is suitable for grooving of the inner and outer contours with up to 1.5 mm in depth and NutauГџenkantenfasung.

Paul Horn 312.2115.43 TN32
Indexable insert with a cutting width of 2.29 mm and maximum cutting depth of 1.5 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (nominal width 2.15 mm) with NutauГџenkantenfasu

Paul Horn 312.2616.43 P20
The indexable insert with a cutting width of 2.79 mm is suitable for grooving of the inner and outer contours with up to 1.5 mm in depth and NutauГџenkantenfasung.

Paul Horn 312.2616.43 TN32
Indexable insert with a cutting width of 2.79 mm and maximum cutting depth of 1.5 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 2.65 mm) with NutauГџenkantenfasung.

Paul Horn 312.2617.43 TN32
Indexable insert with a cutting width of 2.79 mm and maximum cutting depth of 1.75 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (diameter 2.65 mm) with NutauГџenkantenfasung.

Paul Horn 312.3118.53 TN32
Indexable insert with a cutting width of 3.29 mm and maximum cutting depth of 1.75 mm is suitable for the manufacture of Seegerringnuten to DIN471 / 472 (nominal width 3.15 mm) with NutauГџenkantenfas

Paul Horn 312.4120.53 TN32
The indexable insert with a cutting width of 4.29 mm is suitable for grooving of the inner and outer contours with up to 2 mm in depth and NutauГџenkantenfasung.

Paul Horn 312.4125.53 TN32
The indexable insert with a cutting width of 4.29 mm is suitable for grooving of the inner and outer contours with depth and NutauГџenkantenfasung up to 2.5 mm.

Paul Horn 312.5130.63 TN32
The indexable insert with a cutting width of 5.29 mm is suitable for grooving of the inner and outer contours with up to 3 mm in depth and NutauГџenkantenfasung.

Paul Horn 313.0005.10 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 1 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0010.20 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0010.20 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0014.28 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.8 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0014.28 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.8 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0015.30 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0015.30 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0020.40 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 4 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0020.40 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 4 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0025.50 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0025.50 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0070.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 0.77 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 1.5 mm deep.

Paul Horn 313.0080.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 0.87 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 1.7 mm deep.

Paul Horn 313.0090.00 MG12
Insert with a cutting width of 0.97 mm (nominal size Nw = 0.9 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum gro

Paul Horn 313.0090.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 0.97 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 1.9 mm deep.

Paul Horn 313.0100.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.07 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 2.2 mm deep.

Paul Horn 313.0100.1.00 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 1 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0100.1.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 1 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0110.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.21 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with depths up to 2.5 mm.

Paul Horn 313.0130.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.41 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0130.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.41 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0130.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.41 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0130.40 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.41 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0150.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0150.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0150.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0150.40 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0160.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.71 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0160.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.71 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0160.00 TN35
Insert with a cutting width of 1.71 mm (nominal size Nw = 1.6 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum gro

Paul Horn 313.0160.40 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.71 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0185.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.96 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0185.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.96 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0185.00 TN35
Insert with a cutting width of 1.96 mm (nominal size Nw = 1.85 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum gr

Paul Horn 313.0185.40 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.96 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0200.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0200.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0200.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0200.40 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0215.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0215.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0215.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0215.40 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0250.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0250.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0250.00 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0250.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0250.40 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0265.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.76 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0265.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.76 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0265.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.76 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0265.40 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.76 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0300.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0300.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0300.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0300.40 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0315.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 3.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0315.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 3.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0315.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 3.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0315.40 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 3.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0350.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 3.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0350.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 3.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0350.00 TI25
Insert with a cutting width of 3.5 mm and cutting circle diameter of 21.7 is suitable for NutzirkularfrГ¤sen of inner and outer contours with maximum groove depth of 4.5 mm.

Paul Horn 313.0400.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 4 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0400.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 4 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0400.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 4 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0400.40 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 4 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0415.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 4.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0415.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 4.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0415.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 4.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0415.40 MG12
Insert with a cutting width of 26.4 mm (nominal size Nw = 4.15 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum gr

Paul Horn 313.0415.40 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 4.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0500.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0500.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0515.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 5.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0515.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 5.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0515.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 5.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0515.40 MG12
Insert with a cutting width of 5.26 mm (nominal size Nw = 5.15 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum gr

Paul Horn 313.0515.40 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 5.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0600.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 6 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0600.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 6 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.0720.01 TN35
Insert with a pitch range of 1.0 - 2.0 mm or 12-32 transition / inch and a cutting circle diameter of 21.70 mm is suitable for producing internal threads in partial profile.

Paul Horn 313.0815.01 TN35
Insert with a pitch range of 1.5 mm or 16-20 transition / inch and a cutting circle diameter of 21.70 mm is suitable for producing internal threads in partial profile.

Paul Horn 313.0815.02 TN35
The insert full profile and a cutting circle diameter of 21.70 mm is suitable for thread milling metric threads with a pitch 1.50 mm.

Paul Horn 313.1020.01 TN35
Insert with a pitch range of 2.0 mm or 14-16 transition / inch and a cutting circle diameter of 21.70 mm is suitable for producing internal threads in partial profile.

Paul Horn 313.1020.02 TN35
The insert full profile and a cutting circle diameter of 21.70 mm is suitable for thread milling metric threads with a pitch of 2.00 mm.

Paul Horn 313.1105.30 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.21 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 0.5 mm in depth and NutauГџenkantenfasung.

Paul Horn 313.1219.00 AS45
The insert with a cutting diameter of 20 mm and a cutting width of 8.2 mm is suitable for T-slot milling.

Paul Horn 313.1219.00 TI25
The insert with a cutting diameter of 20 mm and a cutting width of 8.2 mm is suitable for T-slot milling.

Paul Horn 313.1307.30 AS45
Insert with a cutting width of 1.41 mm (nominal size Nw = 1.3 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfasung to inner and oute

Paul Horn 313.1307.30 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.41 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 0.7 mm in depth and NutauГџenkantenfasung.

Paul Horn 313.1308.30 AS45
Insert with a cutting width of 1.41 mm (nominal size Nw = 1.3 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfasung to inner and oute

Paul Horn 313.1308.30 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.41 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours of up to 0.85 mm depth and NutauГџenkantenfasung.

Paul Horn 313.1609.35 AS45
Insert with a cutting width of 1.71 mm (nominal size Nw = 1.6 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfasung to inner and oute

Paul Horn 313.1609.35 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.71 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours of up to 0.85 mm depth and NutauГџenkantenfasung.

Paul Horn 313.1610.35 AS45
Insert with a cutting width of 1.71 mm (nominal size Nw = 1.6 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfasung to inner and oute

Paul Horn 313.1610.35 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.71 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 1 mm depth and NutauГџenkantenfasung.

Paul Horn 313.1630.01 TN35
Insert with a pitch range of 3.0 mm or 8-10 transition / inch and a cutting circle diameter of 21.70 mm is suitable for producing internal threads in partial profile.

Paul Horn 313.1630.02 TN35
The insert full profile and a cutting circle diameter of 21.70 mm is suitable for thread milling metric threads with a pitch of 3.00 mm.

Paul Horn 313.1812.35 AS45
Insert with a cutting width of 1.96 mm (nominal size Nw = 1.85 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfasung to inner and out

Paul Horn 313.1812.35 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.96 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 1.25mm deep and NutauГџenkantenfasung.

Paul Horn 313.1835.02 TN35
The insert full profile and a cutting circle diameter of 21.70 mm is suitable for thread milling metric threads with a pitch of 3.50 mm.

Paul Horn 313.2115.35 AS45
Insert with a cutting width of 26.2 mm (nominal size Nw = 2.15 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfasung to inner and out

Paul Horn 313.2115.35 TA45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 1.5 mm in depth and NutauГџenkantenfasung.

Paul Horn 313.2115.35 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 1.5 mm in depth and NutauГџenkantenfasung.

Paul Horn 313.2140.01 TN35
Insert with a pitch range of 4.0 mm or 7 - 8 Gang / inch and a cutting circle diameter of 21.70 mm is suitable for producing internal threads in partial profile.

Paul Horn 313.2140.02 TN35
The insert full profile and a cutting circle diameter of 21.70 mm is suitable for thread milling metric threads with a pitch of 4.00 mm.

Paul Horn 313.2445.01 TN35
Insert with a pitch range of 4.5 mm or 6 - 7 gear / inch and a cutting circle diameter of 21.70 mm is suitable for producing internal threads in partial profile.

Paul Horn 313.2445.02 TN35
The insert full profile and a cutting circle diameter of 21.70 mm is suitable for thread milling metric threads with a pitch of 4.50 mm.

Paul Horn 313.2545.01 TN35
Insert with a pitch range of 2.5 - 4.5 mm or 6 individual - 12 speeds / inch and a cutting circle diameter of 21.70 mm is suitable for producing internal threads in partial profile.

Paul Horn 313.2616.45 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.76 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 1.5 mm in depth and NutauГџenkantenfasung.

Paul Horn 313.2616.45 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.76 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 1.5 mm in depth and NutauГџenkantenfasung.

Paul Horn 313.2617.45 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.76 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours of up to 1.75 mm depth and NutauГџenkantenfasung.

Paul Horn 313.2617.45 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.76 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours of up to 1.75 mm depth and NutauГџenkantenfasung.

Paul Horn 313.3118.45 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 3.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours of up to 1.75 mm depth and NutauГџenkantenfasung.

Paul Horn 313.3118.45 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 3.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours of up to 1.75 mm depth and NutauГџenkantenfasung.

Paul Horn 313.4120.55 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 4.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 2 mm in depth and NutauГџenkantenfasung.

Paul Horn 313.4120.55 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 4.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 2 mm in depth and NutauГџenkantenfasung.

Paul Horn 313.4125.55 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 4.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with depth and NutauГџenkantenfasung up to 2.5 mm.

Paul Horn 313.4125.55 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 4.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with depth and NutauГџenkantenfasung up to 2.5 mm.

Paul Horn 313.4545.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 3 mm is suitable for bore milling and chamfering of inner and outer contours with up to 1.7 mm deep.

Paul Horn 313.4545.30.00 TA45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.6 mm is suitable for bore milling and chamfering of inner and outer contours with up to 3 mm in depth.

Paul Horn 313.5506.02 TN35
The insert full profile and a cutting circle diameter of 21.70 mm is suitable for thread milling of Whitworth pipe threads with a pitch of 6 speed / inch.

Paul Horn 313.5508.02 TN35
The insert full profile and a cutting circle diameter of 21.70 mm is suitable for thread milling of Whitworth pipe threads with a pitch of 8 Gang / inch.

Paul Horn 313.5511.02 TN35
The insert full profile and a cutting circle diameter of 21.70 mm is suitable for thread milling of Whitworth pipe threads with a pitch of 11 threads / inch.

Paul Horn 313.D.0005.10 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 1 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0005.10 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 1 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0005.10 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 1 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0010.20 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0010.20 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0010.20 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0014.28 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.8 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0014.28 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.8 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0014.28 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.8 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0015.30 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0015.30 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0015.30 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0130.00 AS45
Insert with a cutting width of 1.41 mm (nominal size Nw = 1.3 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum gro

Paul Horn 313.D.0130.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.41 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0150.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0150.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0150.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0150.01 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0150.01 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0150.01 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0160.00 AS45
Insert with a cutting width of 1.71 mm (nominal size Nw = 1.6 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum gro

Paul Horn 313.D.0160.00 TN35
Insert with a cutting width of 1.71 mm (nominal size Nw = 1.6 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum gro

Paul Horn 313.D.0185.00 AS45
Insert with a cutting width of 1.96 mm (nominal size Nw = 1.85 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum gr

Paul Horn 313.D.0185.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.96 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0200.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0200.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0200.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0215.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0215.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0215.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.26 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0250.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0250.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0250.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0265.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.76 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0265.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.76 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0265.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.76 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0300.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0300.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0300.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 313.D.0315.00 AS45
Insert with a cutting width of 26.3 mm (nominal size Nw = 3.15 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum gr

Paul Horn 313.D.0315.00 TN35
Insert with a cutting width of 26.3 mm (nominal size Nw = 3.15 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum gr

Paul Horn 313.D.4545.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of .24 mm is suitable for chamfering of inner and outer contours with up to 1.4 mm deep.

Paul Horn 313.D.4545.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of .24 mm is suitable for chamfering of inner and outer contours with up to 1.4 mm deep.

Paul Horn 313.D.4545.00 TN35
The insert with a cutting diameter of 21.7 mm and a cutting width of .24 mm is suitable for chamfering of inner and outer contours with up to 1.4 mm deep.

Paul Horn 313015001AS45
The insert 313.0150.01 AS45 with a cutting diameter of 21.7 mm and a cutting width of 1.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 4.5 mm deep.

Paul Horn 325.0350.52 AS45
The insert with a cutting diameter of 24.8 mm and a cutting width of 3.5 mm is suitable for bore milling of internal and external contours with up to 5 mm depth.

Paul Horn 325.0350.52 TN35
The insert with a cutting diameter of 24.8 mm and a cutting width of 3.5 mm is suitable for bore milling of internal and external contours with up to 5 mm depth.

Paul Horn 328.0082.1.00 TI25
Insert with a cutting width of 0.82 mm and cutting circle diameter of 27.7 is suitable for NutzirkularfrГ¤sen of inner and outer contours with maximum groove depth of 5 mm.

Paul Horn 328.0082.1.00 TN35
Insert with a cutting width of 0.82 mm and cutting circle diameter of 27.7 is suitable for NutzirkularfrГ¤sen of inner and outer contours with maximum groove depth of 5 mm.

Paul Horn 328.0110.2.00 TI25
The insert with a cutting diameter of 28 mm and a cutting width of 1.1 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 9.3 mm deep.

Paul Horn 328.0110.2.00 TN35
Insert with a cutting width of 1.1 mm and cutting circle diameter of 28 is suitable for NutzirkularfrГ¤sen of inner and outer contours with maximum groove depth of 9.3 mm.

Paul Horn 328.0120.2.00 TI25
The insert with a cutting diameter of 28 mm and a cutting width of 1.2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 9.3 mm deep.

Paul Horn 328.0120.2.00 TN35
The insert with a cutting diameter of 28 mm and a cutting width of 1.2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 9.3 mm deep.

Paul Horn 328.0132.2.00 TI25
The insert with a cutting diameter of 28 mm and a cutting width of 1.32 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 9.3 mm deep.

Paul Horn 328.0132.2.00 TN35
The insert with a cutting diameter of 28 mm and a cutting width of 1.32 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 9.3 mm deep.

Paul Horn 328.0150.2.00 AS45
The insert with a cutting diameter of 28 mm and a cutting width of 1.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 9.3 mm deep.

Paul Horn 328.0150.2.00 TI25
The insert with a cutting diameter of 28 mm and a cutting width of 1.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 9.3 mm deep.

Paul Horn 328.0150.2.00 TN35
NutzirkularfrГ¤sen of inner and outer contours with up to 9.3 mm deep.

Paul Horn 328.0160.2.00 AS45
The insert with a cutting diameter of 28 mm and a cutting width of 1.6 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 9.3 mm deep.

Paul Horn 328.0160.2.00 TI25
The insert with a cutting diameter of 28 mm and a cutting width of 1.6 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 9.3 mm deep.

Paul Horn 328.0160.2.00 TN35
Insert with a cutting width of 1.6 mm and cutting circle diameter of 28 is suitable for NutzirkularfrГ¤sen of inner and outer contours with maximum groove depth of 9.3 mm.

Paul Horn 328.0200.00 AS45
The insert with a cutting diameter of 27.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 6.5 mm deep.

Paul Horn 328.0200.00 TN35
The insert with a cutting diameter of 27.7 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 6.5 mm deep.

Paul Horn 328.0200.2.00 AS45
The insert with a cutting diameter of 28 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 9.3 mm deep.

Paul Horn 328.0200.2.00 TI25
The insert with a cutting diameter of 28 mm and a cutting width of 2 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 9.3 mm deep.

Paul Horn 328.0200.2.00 TN35
Insert with a cutting width of 2 mm and cutting circle diameter of 28 is suitable for NutzirkularfrГ¤sen of inner and outer contours with maximum groove depth of 9.3 mm.

Paul Horn 328.0250.00 AS45
The insert with a cutting diameter of 27.7 mm and a cutting width of 2.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 6.5 mm deep.

Paul Horn 328.0250.00 TN35
The insert with a cutting diameter of 27.7 mm and a cutting width of 2.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 6.5 mm deep.

Paul Horn 328.0250.2.00 AS45
The insert with a cutting diameter of 28 mm and a cutting width of 2.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 9.3 mm deep.

Paul Horn 328.0250.2.00 TI25
The insert with a cutting diameter of 28 mm and a cutting width of 2.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 9.3 mm deep.

Paul Horn 328.0250.2.00 TN35
Insert with a cutting width of 2.5 mm and cutting circle diameter of 28 is suitable for NutzirkularfrГ¤sen of inner and outer contours with maximum groove depth of 9.3 mm.

Paul Horn 328.0250.40 TI25
Insert with a cutting width of 2.5 mm and cutting circle diameter of 27.7 is suitable for NutzirkularfrГ¤sen of inner and outer contours with maximum groove depth of 6.5 mm.

Paul Horn 328.0300.00 AS45
The insert with a cutting diameter of 27.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 6.5 mm deep.

Paul Horn 328.0300.00 TN35
The insert with a cutting diameter of 27.7 mm and a cutting width of 3 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 6.5 mm deep.

Paul Horn 328.0300.40 TI25
Insert with a cutting width of 3 mm and cutting circle diameter of 27.7 is suitable for NutzirkularfrГ¤sen of inner and outer contours with maximum groove depth of 6.5 mm.

Paul Horn 328.0350.00 AS45
The insert with a cutting diameter of 27.7 mm and a cutting width of 3.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 6.5 mm deep.

Paul Horn 328.0350.00 TN35
The insert with a cutting diameter of 27.7 mm and a cutting width of 3.5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 6.5 mm deep.

Paul Horn 328.0350.40 TI25
Insert with a cutting width of 3.5 mm and cutting circle diameter of 27.7 is suitable for NutzirkularfrГ¤sen of inner and outer contours with maximum groove depth of 6.5 mm.

Paul Horn 328.0400.00 AS45
The insert with a cutting diameter of 27.7 mm and a cutting width of 4 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 6.5 mm deep.

Paul Horn 328.0400.00 TN35
The insert with a cutting diameter of 27.7 mm and a cutting width of 4 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 6.5 mm deep.

Paul Horn 328.0400.40 TI25
Insert with a cutting width of 4 mm and cutting circle diameter of 27.7 is suitable for NutzirkularfrГ¤sen of inner and outer contours with maximum groove depth of 6.5 mm.

Paul Horn 328.0500.00 AS45
The insert with a cutting diameter of 27.7 mm and a cutting width of 5 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 6.5 mm deep.

Paul Horn 328.0500.00 TN35
Insert with a cutting width of 5 mm and cutting circle diameter of 27.7 is suitable for NutzirkularfrГ¤sen of inner and outer contours with maximum groove depth of 6.5 mm.

Paul Horn 328.0600.00 AS45
The insert with a cutting diameter of 27.7 mm and a cutting width of 6 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 6.5 mm deep.

Paul Horn 328.0600.00 TN35
Insert with a cutting width of 6 mm and cutting circle diameter of 27.7 is suitable for NutzirkularfrГ¤sen of inner and outer contours with maximum groove depth of 6.5 mm.

Paul Horn 328.0720.01 TN35
Insert with a pitch range of 1.0 - 2.0 mm or 14-32 transition / inch and a cutting circle diameter of 27.70 mm is suitable for producing internal threads in partial profile.

Paul Horn 328.1000.00 AS45
The insert with a cutting diameter of 27.7 mm and a cutting width of 10 mm is suitable for NutzirkularfrГ¤sen of inner and outer contours with up to 6.5 mm deep.

Paul Horn 328.1000.00 TN35
Insert with a cutting width of 10 mm and cutting circle diameter of 27.7 is suitable for NutzirkularfrГ¤sen of inner and outer contours with maximum groove depth of 6.5 mm.

Paul Horn 328.1423.00 AS45
The insert with a cutting diameter of 24 mm and a cutting width of 9.2 mm is suitable for T-slot milling of internal and external contours.

< Предыдущая страницаСледующая страница >

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 ... 30