Paul Horn DSDH.4.12.77.12.08
End mills as torus for soft and hard milling, 4-edged, 30 В° helix angle, a theoretical corner radius of 1.9 mm and a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSDH.4.12.99.12.08 TS3K
End mills as torus for soft and hard milling, 4-edged, 30 В° helix angle, a theoretical corner radius of 1.9 mm and a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSDH.4.16.77.16.10
End mills as torus for soft and hard milling, 4-edged, 30 В° helix angle, a theoretical corner radius 2.1 mm with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSDH.4.16.99.16.10 TS3K
End mills as torus for soft and hard milling, 4-edged, 30 В° helix angle, a theoretical corner radius 2.1 mm with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSDS.4.06.63.06.08 TS3K
End mills as torus for soft and hard milling, 4-edged, 30 В° helix angle, a theoretical corner radius of 0.8 mm and a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSDS.4.06.77.06.08 TS3K
End mills as torus for soft and hard milling, 4-edged, 30 В° helix angle, a theoretical corner radius of 0.8 mm and a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSDS.4.08.63.08.10 TS3K
End mills as torus for soft and hard milling, 4-edged, 30 В° helix angle, a theoretical corner radius of 1.4 mm and a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSDS.4.08.77.08.10 TS3K
End mills as torus for soft and hard milling, 4-edged, 30 В° helix angle, a theoretical corner radius of 1.4 mm and a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSDS.4.10.77.10.15 TS3K
End mills as torus for soft and hard milling, 4-edged, 30 В° helix angle, a theoretical corner radius 2.0 mm with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSDS.4.10.99.10.15 TS3K
End mills as torus for soft and hard milling, 4-edged, 30 В° helix angle, a theoretical corner radius 2.0 mm with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSDS.4.12.77.12.15 TS3K
End mills as torus for soft and hard milling, 4-edged, 30 В° helix angle, a theoretical corner radius 2.1 mm with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSDS.4.12.99.12.15 TS3K
End mills as torus for soft and hard milling, 4-edged, 30 В° helix angle, a theoretical corner radius 2.1 mm with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSDS.4.16.77.16.20 TS3K
End mills as torus for soft and hard milling, 4-edged, 30 В° helix angle, a theoretical corner radius 2.8 mm with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSDS.4.16.99.16.20 TS3K
End mills as torus for soft and hard milling, 4-edged, 30 В° helix angle, a theoretical corner radius 2.8 mm with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSF.3.020.38.03 TS3K
End mills as Roughing smooth to hard and soft milling, 3-fluted, 45 В° helix angle, a Eckfase 0.1 mm with a diameter of 2 mm and a shaft diameter of 3 mm.
Paul Horn DSF.3.030.38.03 TS3K
End mills as Roughing smooth to hard and soft milling, 3-fluted, 45 В° helix angle, a Eckfase 0.1 mm with a diameter of 3 mm and a shaft diameter of 3 mm.
Paul Horn DSF.3.040.50.04 TS3K
End mills as Roughing smooth to hard and soft milling, 3-fluted, 45 В° helix angle, a Eckfase 0.1 mm with a diameter of 4 mm and a shaft diameter of 4 mm.
Paul Horn DSF.3.050.50.05 TS3K
End mills as Roughing smooth to hard and soft milling, 3-fluted, 45 В° helix angle, a Eckfase 0.15mm with a diameter of 5 mm and a shaft diameter of 5 mm.
Paul Horn DSF.3.060.63.06 TS3K
End mills as Roughing smooth to hard and soft milling, 3-fluted, 45 В° helix angle, a Eckfase 0.15mm with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSF.3.080.63.08 TS3K
End mills as Roughing smooth to hard and soft milling, 3-fluted, 45 В° helix angle, a Eckfase 0.2 mm and a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSF.3.100.69.10 TS3K
End mills as Roughing smooth to hard and soft milling, 3-fluted, 45 В° helix angle, a Eckfase 0.2 mm with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSF.3.120.77.12 TS3K
End mills as Roughing smooth to hard and soft milling, 3-fluted, 45 В° helix angle, a Eckfase 0.25mm with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSF.3.160.88.16 TS3K
End mills as Roughing smooth to hard and soft milling, 3-fluted, 45 В° helix angle, a Eckfase 0 mm and a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSF.4.040.50.04 TS3K
End mills as Roughing smooth to hard and soft milling, 4-edged, 48 В° helix angle, a Eckfase 0.1 mm with a diameter of 4 mm and a shaft diameter of 4 mm.
Paul Horn DSF.4.060.63.06 TS3K
End mills as Roughing smooth to hard and soft milling, 4-edged, 48 В° helix angle, a Eckfase 0.15mm with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSF.4.080.63.08 TS3K
End mills as Roughing smooth to hard and soft milling, 4-edged, 48 В° helix angle, a Eckfase 0.2 mm and a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSF.4.100.69.10 TS3K
End mills as Roughing smooth to hard and soft milling, 4-edged, 48 В° helix angle, a Eckfase 0.2 mm with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSF.4.120.77.12 TS3K
End mills as Roughing smooth to hard and soft milling, 4-edged, 48 В° helix angle, a Eckfase 0.25mm with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSF.4.160.88.16 TS3K
End mills as Roughing smooth to hard and soft milling, 4-edged, 48 В° helix angle with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSFA.3.060.030 NE2K
End mills DSFA.3.060.030 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.2 mm with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSFA.3.060.050 NE2K
End mills DSFA.3.060.050 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.2 mm with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSFA.3.060.053 NE2K
End mills DSFA.3.060.053 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.2 mm with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSFA.3.060.070 NE2K
End mills DSFA.3.060.070 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.2 mm with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSFA.3.080.030 NE2K
End mills DSFA.3.080.030 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.2 mm and a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSFA.3.080.050 NE2K
End mills DSFA.3.080.050 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.2 mm and a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSFA.3.080.053 NE2K
End mills DSFA.3.080.053 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.2 mm and a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSFA.3.080.070 NE2K
End mills DSFA.3.080.070 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.2 mm and a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSFA.3.100.030 NE2K
End mills DSFA.3.100.030 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.2 mm with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSFA.3.100.050 NE2K
End mills DSFA.3.100.050 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.2 mm with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSFA.3.100.053 NE2K
End mills DSFA.3.100.053 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.2 mm with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSFA.3.100.070 NE2K
End mills DSFA.3.100.070 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.2 mm with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSFA.3.120.030 NE2K
End mills DSFA.3.120.030 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.2 mm with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSFA.3.120.050 NE2K
End mills DSFA.3.120.050 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.2 mm with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSFA.3.120.053 NE2K
End mills DSFA.3.120.053 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.2 mm with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSFA.3.120.070 NE2K
End mills DSFA.3.120.070 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.2 mm with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSFA.3.160.030 NE2K
End mills DSFA.3.160.030 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.5 mm with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSFA.3.160.050 NE2K
End mills DSFA.3.160.050 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.5 mm with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSFA.3.160.053 NE2K
End mills DSFA.3.160.053 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.5 mm with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSFA.3.200.027 NE2K
End mills DSFA.3.200.027 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.5 mm with a diameter of 20 mm and a shaft diameter of 20 mm.
Paul Horn DSFA.3.200.050 NE2K
End mills DSFA.3.200.050 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.5 mm with a diameter of 20 mm and a shaft diameter of 20 mm.
Paul Horn DSFA.3.200.053 NE2K
End mills DSFA.3.200.053 ne2k for the machining of aluminum, 3-fluted, 36 В° -40 В° helix angle, center cutting, Eckfase 0.5 mm with a diameter of 20 mm and a shaft diameter of 20 mm.
Paul Horn DSFD.5.08.10.54.4.08 HD05
End mills pushing as finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 5-edged, Eckfase 0.1 mm and a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSFD.5.08.20.64.3.08 HD05
End mills pushing as finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 5-edged, Eckfase 0.1 mm and a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSFD.5.10.12.60.4.10 HD05
End mills pushing as finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 5-edged, Eckfase 0.1 mm with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSFD.5.10.22.70.3.10 HD05
End mills pushing as finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 5-edged, Eckfase 0.1 mm with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSFD.7.12.15.68.4.12 HD05
End mills pushing as finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 7-edged, Eckfase 0.1 mm with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSFD.7.12.24.77.3.12 HD05
End mills pushing as finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 7-edged, Eckfase 0.1 mm with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSFD.7.16.24.80.4.16 HD05
End mills pushing as finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 7-edged, Eckfase 0.1 mm with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSFD.9.16.24.80.4.16 HD05
End mills pushing as finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 9-edged, Eckfase 0.1 mm with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSFF.4.04.50.04.45 TS3K
End mills as Fasfräser with 90 ° point angle for soft and hard milling with a diameter of 4 mm and 4 cutting edges.
Paul Horn DSFF.4.06.63.06.45 TS3K
End mills as Fasfräser with 90 ° point angle for soft and hard milling with a diameter of 6 mm and 4 cutting edges.
Paul Horn DSFF.4.08.63.08.45 TS3K
End mills as Fasfräser with 90 ° point angle for soft and hard milling with a diameter of 8 mm and 4 cutting edges.
Paul Horn DSFF.4.10.69.10.45 TS3K
End mills as Fasfräser with 90 ° point angle for soft and hard milling at a diameter of 10 mm and 4 cutting edges.
Paul Horn DSFF.4.12.77.12.45 TS3K
End mills as Fasfräser with 90 ° point angle for soft and hard milling at a diameter of 12 mm and 4 cutting edges.
Paul Horn DSFF.MD.30.38.3 MD10
Fasfräser equipped with monocrystalline diamond, Fasfräser with 30 ° chamfer angle to gloss trimming with a diameter of 2.8 mm and 1 cutting.
Paul Horn DSFF.MD.30.66.6 MD10
Fasfräser equipped with monocrystalline diamond, Fasfräser with 30 ° chamfer angle to gloss trimming with a diameter of 2.8 mm and 1 cutting.
Paul Horn DSFF.MD.45.38.3 MD10
Fasfräser equipped with monocrystalline diamond, Fasfräser with 45 ° chamfer angle to gloss trimming with a diameter of 2.8 mm and 1 cutting.
Paul Horn DSFF.MD.45.66.6 MD10
Fasfräser equipped with monocrystalline diamond, Fasfräser with 45 ° chamfer angle to gloss trimming with a diameter of 2.8 mm and 1 cutting.
Paul Horn DSFF.MD.60.38.3 MD10
Fasfräser equipped with monocrystalline diamond, Fasfräser with 60 ° chamfer angle to gloss trimming with a diameter of 2.8 mm and 1 cutting.
Paul Horn DSFF.MD.606.6 MD10
Fasfräser equipped with monocrystalline diamond, Fasfräser with 60 ° chamfer angle to gloss trimming with a diameter of 2.8 mm and 1 cutting.
Paul Horn DSFN.5.08.10.54.0.08 HD05
End mills as finishing cutter neutral, CVD diamond D Equipped for processing z. B. carbon fiber materials, 5-edged, Eckfase 0.1 mm and a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSFN.5.08.20.64.0.08 HD05
End mills as finishing cutter neutral, CVD diamond D Equipped for processing z. B. carbon fiber materials, 5-edged, Eckfase 0.1 mm and a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSFN.5.10.12.60.0.10 HD05
End mills as finishing cutter neutral, CVD diamond D Equipped for processing z. B. carbon fiber materials, 5-edged, Eckfase 0.1 mm with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSFN.5.10.22.70.0.10 HD05
End mills as finishing cutter neutral, CVD diamond D Equipped for processing z. B. carbon fiber materials, 5-edged, Eckfase 0.1 mm with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSFN.7.12.15.68.0.12 HD05
End mills as finishing cutter neutral, CVD diamond D Equipped for processing z. B. carbon fiber materials, 7-edged, Eckfase 0.1 mm with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSFN.7.12.24.77.0.12 HD05
End mills as finishing cutter neutral, CVD diamond D Equipped for processing z. B. carbon fiber materials, 7-edged, Eckfase 0.1 mm with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSFN.7.16.24.80.0.16 HD05
End mills neutral as finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 7-edged, Eckfase 0.1 mm with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSFN.9.16.24.80.0.16 HD05
End mills neutral as finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 9-edged, Eckfase 0.1 mm with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSFRA.3.060.030 NE2K
Kordelschruppfräser DSFRA.3.060.030 ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.4 mm with a diameter of 6 mm and a shaft
Paul Horn DSFRA.3.060.050 NE2K
Kordelschruppfräser DSFRA.3.060.050 ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.4 mm with a diameter of 6 mm and a shaft
Paul Horn DSFRA.3.080.030 NE2K
Kordelschruppfräser DSFRA.3.080.030 ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.5 mm and a diameter of 8 mm and a shaft
Paul Horn DSFRA.3.080.050 NE2K
Kordelschruppfräser DSFRA.3.080.050 ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.5 mm and a diameter of 8 mm and a shaft
Paul Horn DSFRA.3.100.030 NE2K
Kordelschruppfräser DSFRA.3.100.030 ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.5 mm with a diameter of 10 mm and a shaf
Paul Horn DSFRA.3.100.050 NE2K
Kordelschruppfräser DSFRA.3.100.050 ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.5 mm with a diameter of 10 mm and a shaf
Paul Horn DSFRA.3.120.030 NE2K
Kordelschruppfräser DSFRA.3.120.030 ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.5 mm with a diameter of 12 mm and a shaf
Paul Horn DSFRA.3.120.030.B NE2K
Kordelschruppfräser DSFRA.3.120.030.B ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.5 mm with a diameter of 12 mm and a sh
Paul Horn DSFRA.3.120.050 NE2K
Kordelschruppfräser DSFRA.3.120.050 ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.5 mm with a diameter of 12 mm and a shaf
Paul Horn DSFRA.3.120.050.B NE2K
Kordelschruppfräser DSFRA.3.120.050.B ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.5 mm with a diameter of 12 mm and a sh
Paul Horn DSFRA.3.160.030 NE2K
Kordelschruppfräser DSFRA.3.160.030 ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.6 mm with a diameter of 16 mm and a shaf
Paul Horn DSFRA.3.160.030.B NE2K
Kordelschruppfräser DSFRA.3.160.030.B ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.6 mm with a diameter of 16 mm and a sh
Paul Horn DSFRA.3.160.050 NE2K
Kordelschruppfräser DSFRA.3.160.050 ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.6 mm with a diameter of 16 mm and a shaf
Paul Horn DSFRA.3.160.050.B NE2K
Kordelschruppfräser DSFRA.3.160.050.B ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.6 mm with a diameter of 16 mm and a sh
Paul Horn DSFRA.3.200.027 NE2K
Kordelschruppfräser DSFRA.3.200.027 ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.8 mm with a diameter of 20 mm and a shaf
Paul Horn DSFRA.3.200.027.B NE2K
Kordelschruppfräser DSFRA.3.200.027.B ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.8 mm with a diameter of 20 mm and a sh
Paul Horn DSFRA.3.200.050 NE2K
Kordelschruppfräser DSFRA.3.200.050 ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.8 mm with a diameter of 20 mm and a shaf
Paul Horn DSFRA.3.200.050.B NE2K
Kordelschruppfräser DSFRA.3.200.050.B ne2k for the machining of aluminum, 3-fluted, 36 ° -40 ° helix angle, center cutting, internal coolant supply, Eckfase 0.8 mm with a diameter of 20 mm and a sh
Paul Horn DSFU.5.08.10.54.4.08 HD05
End mills withdrawing than finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 5-edged, Eckfase 0.1 mm and a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSFU.5.08.20.64.3.08 HD05
End mills withdrawing than finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 5-edged, Eckfase 0.1 mm and a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSFU.5.10.12.60.4.10 HD05
End mills withdrawing than finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 5-edged, Eckfase 0.1 mm with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSFU.5.10.22.70.3.10 HD05
End mills withdrawing than finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 5-edged, Eckfase 0.1 mm with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSFU.7.12.15.68.4.12 HD05
End mills withdrawing than finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 7-edged, Eckfase 0.1 mm with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSFU.7.12.24.77.3.12 HD05
End mills withdrawing than finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 7-edged, Eckfase 0.1 mm with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSFU.7.16.24.80.4.16 HD05
End mills withdrawing than finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 7-edged, Eckfase 0.1 mm with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSFU.9.16.24.80.4.16 HD05
End mills withdrawing than finishing cutter, CVD diamond D Equipped for processing z. B. carbon fiber materials, 9-edged, Eckfase 0.1 mm with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSK.2.010.063.06 TS3H
End mills for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.010.063.06 TS3K
End mills for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.015.063.06 TS3H
End mills for soft and hard milling with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.015.063.06 TS3K
End mills for soft and hard milling with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.02.08.04.00 HD03
End mills for soft and hard milling with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm.
Paul Horn DSK.2.020.04.04.00 HD03
End mills for soft and hard milling with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm.
Paul Horn DSK.2.020.06.04.00 HD03
End mills for soft and hard milling with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm.
Paul Horn DSK.2.020.063.06 TS3H
End mills for soft and hard milling with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.020.063.06 TS3K
End mills for soft and hard milling with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.020.077.06 TS3H
End mills for soft and hard milling with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.020.077.06 TS3K
End mills for soft and hard milling with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.03.09.06.00 HD03
End mills for soft and hard milling with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.03.12.06.00 HD03
End mills for soft and hard milling with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.03.15.06.00 HD03
End mills for soft and hard milling with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.030.063.06 TS3H
End mills for soft and hard milling with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.030.063.06 TS3K
End mills for soft and hard milling with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.030.063.06.2 TS3H
End mills Full Radius for soft and hard milling with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.030.063.06.2 TS3K
End mills Full Radius for soft and hard milling with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.030.077.06 TS3H
End mills for soft and hard milling with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.030.077.06 TS3K
End mills for soft and hard milling with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.04.10.06.00 HD05
End mills for soft and hard milling with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.04.15.06.00 HD05
End mills for soft and hard milling with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.04.20.06.00 HD05
End mills for soft and hard milling with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.040.063.06 TS3H
End mills for soft and hard milling with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.040.063.06 TS3K
End mills for soft and hard milling with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.040.063.06.2 TS3H
End mills Full Radius for soft and hard milling with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.040.063.06.2 TS3K
End mills Full Radius for soft and hard milling with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.040.077.06 TS3H
End mills for soft and hard milling with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.040.077.06 TS3K
End mills for soft and hard milling with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.050.063.06 TS3H
End mills for soft and hard milling with radius 2.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.050.063.06 TS3K
End mills for soft and hard milling with radius 2.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.050.077.06 TS3H
End mills for soft and hard milling with radius 2.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.050.077.06 TS3K
End mills for soft and hard milling with radius 2.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.050.077.06.2 TS3H
End mills Full Radius for soft and hard milling with radius 2.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.050.077.06.2 TS3K
End mills Full Radius for soft and hard milling with radius 2.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.06.20.06.00 HD08
End mills for soft and hard milling with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.06.25.06.00 HD08
End mills for soft and hard milling with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.06.30.06.00 HD08
End mills for soft and hard milling with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.060.063.06 TS3H
End mills for soft and hard milling with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.060.063.06 TS3K
End mills for soft and hard milling with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.060.077.06 TS3H
End mills for soft and hard milling with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.060.077.06 TS3K
End mills for soft and hard milling with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.060.077.06.2 TS3H
End mills Full Radius for soft and hard milling with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.060.077.06.2 TS3K
End mills Full Radius for soft and hard milling with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSK.2.060.099.08 TS3H
End mills for soft and hard milling with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 8 mm.
Paul Horn DSK.2.060.099.08 TS3K
End mills for soft and hard milling with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 8 mm.
Paul Horn DSK.2.08.25.08.00 HD08
End mills for soft and hard milling with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSK.2.08.40.08.00 HD08
End mills for soft and hard milling with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSK.2.080.063.08 TS3H
End mills for soft and hard milling with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSK.2.080.063.08 TS3K
End mills for soft and hard milling with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSK.2.080.077.08 TS3H
End mills for soft and hard milling with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSK.2.080.077.08 TS3K
End mills for soft and hard milling with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSK.2.080.088.08.2 TS3H
End mills Full Radius for soft and hard milling with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSK.2.080.088.08.2 TS3K
End mills Full Radius for soft and hard milling with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSK.2.080.099.08 TS3H
End mills for soft and hard milling with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSK.2.080.099.08 TS3K
End mills for soft and hard milling with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSK.2.080.119.10 TS3H
End mills for soft and hard milling with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 10 mm.
Paul Horn DSK.2.080.119.10 TS3K
End mills for soft and hard milling with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 10 mm.
Paul Horn DSK.2.10.30.10.00 HD08
End mills for soft and hard milling with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSK.2.10.50.10.00 HD08
End mills for soft and hard milling with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSK.2.100.077.10 TS3H
End mills for soft and hard milling with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSK.2.100.077.10 TS3K
End mills for soft and hard milling with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSK.2.100.099.10 TS3H
End mills for soft and hard milling with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSK.2.100.099.10 TS3K
End mills for soft and hard milling with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSK.2.100.101.10.2 TS3H
End mills Full Radius for soft and hard milling with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSK.2.100.101.10.2 TS3K
End mills Full Radius for soft and hard milling with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSK.2.100.119.12 TS3H
End mills for soft and hard milling with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 12 mm.
Paul Horn DSK.2.12.30.12.00 HD08
End mills for soft and hard milling with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSK.2.12.60.12.00 HD08
End mills for soft and hard milling with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSK.2.120.077.12 TS3H
End mills for soft and hard milling with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSK.2.120.077.12 TS3K
End mills for soft and hard milling with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSK.2.120.099.12 TS3H
End mills for soft and hard milling with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSK.2.120.099.12 TS3K
End mills for soft and hard milling with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSK.2.120.119.12.2 TS3H
End mills Full Radius for soft and hard milling with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSK.2.120.119.12.2 TS3K
End mills Full Radius for soft and hard milling with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSK.2.160.099.16 TS3H
End mills for soft and hard milling with radius 8 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSK.2.160.099.16 TS3K
End mills for soft and hard milling with radius 8 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSK.2.160.119.16.2 TS3H
End mills Full Radius for soft and hard milling with radius 8 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSK.4.060.063.06 TS3H
End mills for soft and hard milling with radius 3 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSK.4.060.077.06 TS3H
End mills for soft and hard milling with radius 3 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSK.4.060.099.08 TS3H
End mills for soft and hard milling with radius 3 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 8 mm.
Paul Horn DSK.4.080.063.08 TS3H
End mills for soft and hard milling with radius 4 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSK.4.080.077.08 TS3H
End mills for soft and hard milling with radius 4 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSK.4.080.119.10 TS3H
End mills for soft and hard milling with radius 4 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 10 mm.
Paul Horn DSK.4.100.077.10 TS3H
End mills for soft and hard milling with radius 5 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSK.4.100.119.12 TS3H
End mills for soft and hard milling with radius 5 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 12 mm.
Paul Horn DSK.4.120.077.12 TS3H
End mills for soft and hard milling with radius 6 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSK.4.120.099.12 TS3H
End mills for soft and hard milling with radius 6 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSK.4.160.099.16 TS3K
End mills for soft and hard milling with radius 8 mm, 4 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSK.MD.010.38.3 MD10
End mills equipped with monocrystalline diamond, micro cutters for gloss trimming with radius 0.05mm, 1-edged with a diameter of .1 mm and a shaft diameter of 3 mm.
Paul Horn DSK.MD.015.38.3 MD10
End mills equipped with monocrystalline diamond, micro cutters for gloss trimming with radius 0.075 mm, 1-edged with a diameter of .15 mm and a shaft diameter of 3 mm.
Paul Horn DSK.MD.020.38.3 MD10
End mills equipped with monocrystalline diamond, micro cutters for gloss trimming with radius 0.1 mm, 1-edged with a diameter of .2 mm and a shaft diameter of 3 mm.
Paul Horn DSK.MD.030.38.3 MD10
End mills equipped with monocrystalline diamond, micro cutters for gloss trimming with radius 0.15mm, 1-edged with a diameter of .3 mm and a shaft diameter of 3 mm.
Paul Horn DSK.MD.040.38.3 MD10
End mills equipped with monocrystalline diamond, micro cutters for gloss trimming with radius 0.2 mm, 1-edged with a diameter of .4 mm and a shaft diameter of 3 mm.
Paul Horn DSK.MD.050.38.3 MD10
End mills equipped with monocrystalline diamond, micro cutters for gloss trimming with radius of 0.25 mm, 1-edged with a diameter of 0.5 mm and a shaft diameter of 3 mm.
Paul Horn DSK.MD.080.38.3 MD10
End mills equipped with monocrystalline diamond, micro cutters for gloss trimming with radius 0.4 mm, 1-edged with a diameter of 0.8 mm and a shaft diameter of 3 mm.
Paul Horn DSK.MD.100.38.3 MD10
End mills equipped with monocrystalline diamond, micro cutters for gloss trimming with radius 0.5 mm, 1-edged with a diameter of 1 mm and a shaft diameter of 3 mm.
Paul Horn DSK.MD.200.38.3 MD10
End mills equipped with monocrystalline diamond, micro cutters for gloss trimming with radius 1 mm, 1-edged with a diameter of 2 mm and a shaft diameter of 3 mm.
Paul Horn DSK.MD.200.66.6 MD10
End mills equipped with monocrystalline diamond, micro cutters for gloss trimming with radius 1 mm, 1-edged with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSK.MD.300.66.6 MD10
End mills equipped with monocrystalline diamond, micro cutters for gloss trimming with radius 1.5 mm, 1-edged with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSK.MD.400.66.6 MD10
End mills equipped with monocrystalline diamond, micro cutters for gloss trimming with radius 2 mm, 1-edged with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSK.MD.500.66.6 MD10
End mills equipped with monocrystalline diamond, micro cutters for gloss trimming with radius 2.5 mm, 1-edged with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSK.MD.600.66.6 MD10
End mills equipped with monocrystalline diamond, micro cutters for gloss trimming with radius 3 mm, 1-edged with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKA.2.040.030 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKA.2.040.050 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKA.2.040.070 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKA.2.050.030 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 2.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKA.2.050.050 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 2.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKA.2.050.070 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 2.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKA.2.060.030 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKA.2.060.050 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKA.2.060.070 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKA.2.080.030 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKA.2.080.050 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKA.2.080.070 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKA.2.100.030 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKA.2.100.050 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKA.2.100.070 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKA.2.120.030 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKA.2.120.050 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKA.2.120.070 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKA.2.160.030 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 8 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSKA.2.160.050 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 8 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSKA.2.200.030 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 10 mm, 2 cutting edges with a diameter of 20 mm and a shaft diameter of 20 mm.
Paul Horn DSKA.2.200.050 MG3K
Ball cutter for Alunimiumbearbeitung center cutting with radius 10 mm, 2 cutting edges with a diameter of 20 mm and a shaft diameter of 20 mm.
Paul Horn DSKC.2.010.063.06 TSCC
End mills for working Colbalt-chromium alloys with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 6 mm.
Paul Horn DSKC.2.015.063.06 TSCC
End mills for working Colbalt-chromium alloys with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKC.2.020.063.06 TSCC
End mills for working Colbalt-chromium alloys with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSKC.2.020.077.06 TSCC
End mills for working Colbalt-chromium alloys with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSKC.2.030.063.06 TSCC
End mills for working Colbalt-chromium alloys with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSKC.2.030.063.06.2 TSCC
End mills for working Colbalt-chromium alloys with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSKC.2.030.077.06 TSCC
End mills for working Colbalt-chromium alloys with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSKC.3.040.063.06 TSCC
End mills for working Colbalt-chromium alloys with radius 2 mm, 3-edged with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKC.3.040.063.06.2 TSCC
End mills for working Colbalt-chromium alloys with radius 2 mm, 3-edged with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKC.3.040.077.06 TSCC
End mills for working Colbalt-chromium alloys with radius 2 mm, 3-edged with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKC.4.050.063.06 TSCC
End mills for working Colbalt-chromium alloys with radius 2.5 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKC.4.050.063.06.2 TSCC
End mills for working Colbalt-chromium alloys with radius 2.5 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKC.4.050.077.06 TSCC
End mills for working Colbalt-chromium alloys with radius 2.5 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKC.4.060.063.06 TSCC
End mills for working Colbalt-chromium alloys with radius 3 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKC.4.060.063.06.2 TSCC
End mills for working Colbalt-chromium alloys with radius 3 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKC.4.060.077.06 TSCC
End mills for working Colbalt-chromium alloys with radius 3 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKC.4.060.099.08 TSCC
End mills for working Colbalt-chromium alloys with radius 3 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 8 mm.
Paul Horn DSKC.5.080.063.08 TSCC
End mills for working Colbalt-chromium alloys with radius 4 mm, 5 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKC.5.080.077.08 TSCC
End mills for working Colbalt-chromium alloys with radius 4 mm, 5 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKC.5.080.088.08.2 TSCC
End mills for working Colbalt-chromium alloys with radius 4 mm, 5 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKC.5.080.099.08 TSCC
End mills for working Colbalt-chromium alloys with radius 4 mm, 5 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKC.5.080.119.10 TSCC
End mills for working Colbalt-chromium alloys with radius 4 mm, 5 cutting edges with a diameter of 8 mm and a shaft diameter of 10 mm.
Paul Horn DSKC.5.100.077.10 TSCC
End mills for working Colbalt-chromium alloys with radius 5 mm, 5 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKC.5.100.099.10 TSCC
End mills for working Colbalt-chromium alloys with radius 5 mm, 5 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKC.5.100.101.10.2 TSCC
End mills for working Colbalt-chromium alloys with radius 5 mm, 5 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKC.5.100.119.12 TSCC
End mills for working Colbalt-chromium alloys with radius 5 mm, 5 cutting edges with a diameter of 10 mm and a shaft diameter of 12 mm.
Paul Horn DSKC.7.120.077.12 TSCC
End mills for working Colbalt-chromium alloys with radius 6 mm, 7-edged with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKC.7.120.099.12 TSCC
End mills for working Colbalt-chromium alloys with radius 6 mm, 7-edged with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKC.7.120.119.12.2 TSCC
End mills for working Colbalt-chromium alloys with radius 6 mm, 7-edged with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKC.7.160.099.16 TSCC
End mills for working Colbalt-chromium alloys with radius 8 mm, 7-edged with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSKC.7.160.119.16.2 TSCC
End mills for working Colbalt-chromium alloys with radius 8 mm, 7-edged with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSKG.3.02.50.04.L20 CD5K
End mills Full Radius for working graphite with radius 1 mm, 3-edged with a diameter of 2 mm and a shaft diameter of 4 mm.
Paul Horn DSKG.3.02.63.06.L25 CD5K
End mills Full Radius for working graphite with radius 1 mm, 3-edged with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSKG.3.03.50.04.L20 CD5K
End mills Full Radius for working graphite with radius 1.5 mm, 3-edged with a diameter of 3 mm and a shaft diameter of 4 mm.
Paul Horn DSKG.3.03.63.06.L25 CD5K
End mills Full Radius for working graphite with radius 1.5 mm, 3-edged with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSKG.3.04.63.06.L30 CD5K
End mills Full Radius for working graphite with radius 2 mm, 3-edged with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKG.3.05.63.06.L30 CD5K
End mills Full Radius for working graphite with radius 2.5 mm, 3-fluted, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKG.3.06.77.06 CD5K
End mills Full Radius for working graphite with radius 3 mm, 3-edged with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKG.3.08.77.08 CD5K
End mills Full Radius for working graphite with radius 4 mm, 3-edged with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKG.3.10.77.10 CD5K
End mills Full Radius for working graphite with radius 5 mm, 3-edged with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKG.3.12.77.12 CD5K
End mills Full Radius for working graphite with radius 6 mm, 3-edged with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKGL.2.02.099.04 CD5K
End mills Full Radius for working graphite with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm.
Paul Horn DSKGL.2.03.099.04 CD5K
End mills Full Radius for working graphite with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm.
Paul Horn DSKGL.2.04.099.06 CD5K
End mills Full Radius for working graphite with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKGL.2.06.099.06 CD5K
End mills Full Radius for working graphite with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKGL.2.08.149.08 CD5K
End mills Full Radius diamond- coated
Paul Horn DSKGL.2.10.149.10 CD5K
End mills Full Radius for working graphite with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKH.2.015.063.06 TS3E
End mills for hard machining 50-70HRC with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.020.063.06 TS3E
End mills for hard machining 50-70HRC with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.030.063.06 TS3E
End mills for hard machining 50-70HRC with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.030.063.06.2 TS3E
End mills Full Radius for hard machining 50-70HRC with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.030.077.06 TS3E
End mills for hard machining 50-70HRC with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.040.015 TS3E
End mills for hard machining 50-70HRC with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.040.030 TS3E
End mills for hard machining 50-70HRC with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.040.050 TS3E
End mills for hard machining 50-70HRC with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.040.063.06 TS3E
End mills for hard machining 50-70HRC with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.040.063.06.2 TS3E
End mills Full Radius for hard machining 50-70HRC with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.040.070 TS3E
End mills for hard machining 50-70HRC with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.040.077.06 TS3E
End mills for hard machining 50-70HRC with radius 2 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.050.015 TS3E
End mills for hard machining 50-70HRC with radius 2.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.050.030 TS3E
End mills for hard machining 50-70HRC with radius 2.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.050.050 TS3E
End mills for hard machining 50-70HRC with radius 2.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.050.063.06 TS3E
End mills for hard machining 50-70HRC with radius 2.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.050.063.06.2 TS3E
End mills Full Radius for hard machining 50-70HRC with radius 2.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.050.070 TS3E
End mills for hard machining 50-70HRC with radius 2.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.050.077.06 TS3E
End mills for hard machining 50-70HRC with radius 2.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.060.015 TS3E
End mills for hard machining 50-70HRC with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.060.030 TS3E
End mills for hard machining 50-70HRC with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.060.050 TS3E
End mills for hard machining 50-70HRC with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.060.063.06.2 TS3E
End mills Full Radius for hard machining 50-70HRC with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.060.070 TS3E
End mills for hard machining 50-70HRC with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.060.077.06 TS3E
End mills for hard machining 50-70HRC with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.2.080.015 TS3E
End mills for hard machining 50-70HRC with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKH.2.080.030 TS3E
End mills for hard machining 50-70HRC with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKH.2.080.050 TS3E
End mills for hard machining 50-70HRC with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKH.2.080.063.08 TS3E
End mills for hard machining 50-70HRC with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKH.2.080.070 TS3E
End mills for hard machining 50-70HRC with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKH.2.080.077.08 TS3E
End mills for hard machining 50-70HRC with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKH.2.080.088.08.2 TS3E
End mills Full Radius for hard machining 50-70HRC with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKH.2.080.099.08 TS3E
End mills for hard machining 50-70HRC with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKH.2.100.015 TS3E
End mills for hard machining 50-70HRC with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKH.2.100.030 TS3E
End mills for hard machining 50-70HRC with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKH.2.100.050 TS3E
End mills for hard machining 50-70HRC with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKH.2.100.070 TS3E
End mills for hard machining 50-70HRC with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKH.2.100.077.10 TS3E
End mills for hard machining 50-70HRC with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKH.2.100.099.10 TS3E
End mills for hard machining 50-70HRC with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKH.2.100.101.10.2 TS3E
End mills Full Radius for hard machining 50-70HRC with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKH.2.120.015 TS3E
End mills for hard machining 50-70HRC with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKH.2.120.030 TS3E
End mills for hard machining 50-70HRC with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKH.2.120.050 TS3E
End mills for hard machining 50-70HRC with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKH.2.120.070 TS3E
End mills for hard machining 50-70HRC with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKH.2.120.077.12 TS3E
End mills for hard machining 50-70HRC with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKH.2.120.099.12 TS3E
End mills for hard machining 50-70HRC with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKH.2.120.119.12.2 TS3E
End mills Full Radius for hard machining 50-70HRC with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKH.2.160.099.16 TS3E
End mills for hard machining 50-70HRC with radius 8 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSKH.4.040.015 TS3E
End mills for hard machining 50-70HRC with radius 2 mm, 4 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.4.040.030 TS3E
End mills for hard machining 50-70HRC with radius 2 mm, 4 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.4.040.050 TS3E
End mills for hard machining 50-70HRC with radius 2 mm, 4 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.4.040.070 TS3E
End mills for hard machining 50-70HRC with radius 2 mm, 4 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.4.050.015 TS3E
End mills for hard machining 50-70HRC with radius 2.5 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.4.050.030 TS3E
End mills for hard machining 50-70HRC with radius 2.5 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.4.050.050 TS3E
End mills for hard machining 50-70HRC with radius 2.5 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.4.050.070 TS3E
End mills for hard machining 50-70HRC with radius 2.5 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.4.060.015 TS3E
End mills for hard machining 50-70HRC with radius 3 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.4.060.030 TS3E
End mills for hard machining 50-70HRC with radius 3 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.4.060.050 TS3E
End mills for hard machining 50-70HRC with radius 3 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.4.060.070 TS3E
End mills for hard machining 50-70HRC with radius 3 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKH.4.080.015 TS3E
End mills for hard machining 50-70HRC with radius 4 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKH.4.080.030 TS3E
End mills for hard machining 50-70HRC with radius 4 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKH.4.080.050 TS3E
End mills for hard machining 50-70HRC with radius 4 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKH.4.080.070 TS3E
End mills for hard machining 50-70HRC with radius 4 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKH.4.100.015 TS3E
End mills for hard machining 50-70HRC with radius 5 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKH.4.100.030 TS3E
End mills for hard machining 50-70HRC with radius 5 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKH.4.100.050 TS3E
End mills for hard machining 50-70HRC with radius 5 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKH.4.100.070 TS3E
End mills for hard machining 50-70HRC with radius 5 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKH.4.120.015 TS3E
End mills for hard machining 50-70HRC with radius 6 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKH.4.120.030 TS3E
End mills for hard machining 50-70HRC with radius 6 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKH.4.120.050 TS3E
End mills for hard machining 50-70HRC with radius 6 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKH.4.120.070 TS3E
End mills for hard machining 50-70HRC with radius 6 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKK.4.030.050.04 CN2K
End mills Full Radius for processing copper with radius 1.5 mm, 4-edged, with a diameter of 3 mm and a shaft diameter of 4 mm.
Paul Horn DSKK.4.030.063.06 CN2K
End mills Full Radius for processing copper with radius 1.5 mm, 4-edged, with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSKK.4.040.063.06 CN2K
End mills Full Radius for processing copper with radius 2 mm, 4 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm.
Paul Horn DSKK.4.050.063.06 CN2K
End mills Full Radius for processing copper with radius 2.5 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm.
Paul Horn DSKK.4.060.063.06 CN2K
End mills Full Radius for processing copper with radius 3 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm.
Paul Horn DSKK.4.080.077.08 CN2K
End mills Full Radius for processing copper with radius 4 mm, 4 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm.
Paul Horn DSKK.4.100.077.10 CN2K
End mills Full Radius for processing copper with radius 5 mm, 4 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm.
Paul Horn DSKK.4.120.088.12 CN2K
End mills Full Radius for processing copper with radius 6 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm.
Paul Horn DSKL.2.060.149.08 TS3H
End mills Full Radius for soft and hard milling with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 8 mm.
Paul Horn DSKL.2.060.149.08 TS3K
End mills Full Radius for soft and hard milling with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 8 mm.
Paul Horn DSKL.2.080.149.10 TS3H
End mills Full Radius for soft and hard milling with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 10 mm.
Paul Horn DSKL.2.080.149.10 TS3K
End mills Full Radius for soft and hard milling with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 10 mm.
Paul Horn DSKL.2.100.149.12 TS3H
End mills Full Radius for soft and hard milling with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 12 mm.
Paul Horn DSKL.2.100.149.12 TS3K
End mills Full Radius for soft and hard milling with radius 5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 12 mm.
Paul Horn DSKL.2.160.149.16 TS3H
End mills Full Radius TiAlN coated
Paul Horn DSKL.2.160.149.16 TS3K
End mills Full Radius for soft and hard milling with radius 8 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm.
Paul Horn DSKLC.4.060.149.08 TSCC
End mills for soft and hard milling with radius 3 mm, 4 cutting edges with a diameter of 6 mm and a shaft diameter of 8 mm.
Paul Horn DSKLC.5.080.149.10 TSCC
End mills for soft and hard milling with radius 4 mm, 5 cutting edges with a diameter of 8 mm and a shaft diameter of 10 mm.
Paul Horn DSKLC.5.100.149.12 TSCC
End mills for soft and hard milling with radius 5 mm, 5 cutting edges with a diameter of 10 mm and a shaft diameter of 12 mm.
Paul Horn DSKLC.7.120.149.16 TSCC
End mills for soft and hard milling with radius 6 mm, 7-edged with a diameter of 12 mm and a shaft diameter of 16 mm.
Paul Horn DSKLH.2.060.149.08 TS3E
End mills Full Radius for soft and hard milling with radius 3 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 8 mm.
Paul Horn DSKLH.2.080.149.10 TS3E
End mills Full Radius for soft and hard milling with radius 4 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 10 mm.
Paul Horn DSKLH.2.120.149.16 TS3E
End mills Full Radius for soft and hard milling with radius 6 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 16 mm.
Paul Horn DSKM.2.010.030 TS3K
Micro cutters full radius DSKM.2.010.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.010.050 TS3K
Micro cutters full radius DSKM.2.010.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.010.070 TS3K
Micro cutters full radius DSKM.2.010.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.02.39.06.L03 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.1 mm, 2 cutting edges with a diameter of 0.2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.02.63.04.L00 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.1 mm, 2 cutting edges with a diameter of 0.2 mm and a shaft diameter of 4 mm.
Paul Horn DSKM.2.02.63.04.L00 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.1 mm, 2 cutting edges with a diameter of 0.2 mm and a shaft diameter of 4 mm.
Paul Horn DSKM.2.02.63.06.L03 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.1 mm, 2 cutting edges with a diameter of 0.2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.02.63.06.L03 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.1 mm, 2 cutting edges with a diameter of 0.2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.020.030 TS3K
Micro cutters full radius DSKM.2.020.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.020.050 TS3K
Micro cutters full radius DSKM.2.020.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.020.070 TS3K
Micro cutters full radius DSKM.2.020.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.03.39.06.L06 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.15mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.03.39.06.L06 TS3K
Micro cutter full radius TiAlN coated
Paul Horn DSKM.2.03.63.06.L06 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.15mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.03.63.06.L06 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.15mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.030.030 TS3K
Micro cutters full radius DSKM.2.030.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.030.050 TS3K
Micro cutters full radius DSKM.2.030.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.030.070 TS3K
Micro cutters full radius DSKM.2.030.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.04.39.06.L08 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.2 mm, 2 cutting edges with a diameter of 0.4 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.04.39.06.L08 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.2 mm, 2 cutting edges with a diameter of 0.4 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.04.63.06.L08 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.2 mm, 2 cutting edges with a diameter of 0.4 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.04.63.06.L08 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.2 mm, 2 cutting edges with a diameter of 0.4 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.05.39.06.L11 TS3H
Cutter shank as micro cutters for soft and hard milling with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.05.39.06.L11 TS3K
Cutter shank as micro cutters for soft and hard milling with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.05.39.06.L31 TS3H
Cutter shank as micro cutters for soft and hard milling with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.05.39.06.L31 TS3K
Cutter shank as micro cutters for soft and hard milling with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.05.63.04.L31 TS3H
Cutter shank as micro cutters for soft and hard milling with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm.
Paul Horn DSKM.2.05.63.04.L31 TS3K
Cutter shank as micro cutters for soft and hard milling with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm.
Paul Horn DSKM.2.05.63.04.L61 TS3H
Cutter shank as micro cutters for soft and hard milling with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm.
Paul Horn DSKM.2.05.63.04.L61 TS3K
Cutter shank as micro cutters for soft and hard milling with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm.
Paul Horn DSKM.2.05.63.04.L81 TS3H
Cutter shank as micro cutters for soft and hard milling with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm.
Paul Horn DSKM.2.05.63.04.L81 TS3K
Cutter shank as micro cutters for soft and hard milling with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm.
Paul Horn DSKM.2.05.63.06.L11 TS3H
Cutter shank as micro cutters for soft and hard milling with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.05.63.06.L11 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.05.63.06.L31 TS3H
Cutter shank as micro cutters for soft and hard milling with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.05.63.06.L31 TS3K
Cutter shank as micro cutters for soft and hard milling with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.050.030 TS3K
Micro cutters full radius DSKM.2.050.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.050.050 TS3K
Micro cutters full radius DSKM.2.050.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.050.070 TS3K
Micro cutters full radius DSKM.2.050.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.06.39.06.L13 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.3 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.06.39.06.L13 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.3 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.06.39.06.L41 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.3 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.06.39.06.L41 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.3 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.06.63.06.L13 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.3 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.06.63.06.L13 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.3 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.06.63.06.L41 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.3 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.06.63.06.L41 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.3 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.060.030 TS3K
Micro cutters full radius DSKM.2.060.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.060.050 TS3K
Micro cutters full radius DSKM.2.060.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.060.070 TS3K
Micro cutters full radius DSKM.2.060.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.08.39.06.L17 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.4 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.08.39.06.L17 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.4 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.08.39.06.L51 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.4 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.08.63.06.L17 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.4 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.08.63.06.L17 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.4 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.08.63.06.L51 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.4 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.08.63.06.L51 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.4 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.080.030 TS3K
Micro cutters full radius DSKM.2.080.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.080.050 TS3K
Micro cutters full radius DSKM.2.080.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.080.070 TS3K
Micro cutters full radius DSKM.2.080.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.10.39.06.L21 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.10.39.06.L21 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.10.39.06.L61 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.10.39.06.L61 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.10.63.04.L00 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm.
Paul Horn DSKM.2.10.63.04.L00 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm.
Paul Horn DSKM.2.10.63.04.L11 TS3H
Micro cutter full radius TiAlN coated
Paul Horn DSKM.2.10.63.04.L11 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm.
Paul Horn DSKM.2.10.63.04.L15 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm.
Paul Horn DSKM.2.10.63.04.L15 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm.
Paul Horn DSKM.2.10.63.04.L41 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm.
Paul Horn DSKM.2.10.63.04.L41 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm.
Paul Horn DSKM.2.10.63.04.L61 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm.
Paul Horn DSKM.2.10.63.04.L61 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm.
Paul Horn DSKM.2.10.63.06.L21 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.10.63.06.L21 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.10.63.06.L61 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.10.63.06.L61 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.100.030 TS3K
Micro cutters full radius DSKM.2.100.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.100.050 TS3K
Micro cutters full radius DSKM.2.100.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.100.070 TS3K
Micro cutters full radius DSKM.2.100.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.12.39.06.L25 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.6 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.12.39.06.L25 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.6 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.12.39.06.L81 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.6 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.12.39.06.L81 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.6 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.12.63.06.L25 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.6 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.12.63.06.L25 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.6 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.12.63.06.L81 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.6 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.12.63.06.L81 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.6 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.120.030
Microcutters full radius, 2blades, 30В° helixangle, centercutting
Paul Horn DSKM.2.120.050 TS3K
Micro cutters full radius DSKM.2.120.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.120.070 TS3K
Micro cutters full radius DSKM.2.120.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.15.39.06.L11 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.15.39.06.L11 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.15.39.06.L31 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.15.39.06.L31 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.15.63.06.L11 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.15.63.06.L11 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.15.63.06.L31 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.15.63.06.L31 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.150.030 TS3K
Micro cutters full radius DSKM.2.150.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.150.050 TS3K
Micro cutters full radius DSKM.2.150.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.150.070 TS3K
Micro cutters full radius DSKM.2.150.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.20.39.06.L11 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.20.39.06.L11 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.20.39.06.L31 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.20.39.06.L31 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.20.63.06.L11 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.20.63.06.L11 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.20.63.06.L31 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.20.63.06.L31 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.200.030 TS3K
Micro cutters full radius DSKM.2.200.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.200.050 TS3K
Micro cutters full radius DSKM.2.200.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.200.070 TS3K
Micro cutters full radius DSKM.2.200.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.25.39.06.L11 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 1.25mm, 2 blades with a diameter of 2.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.25.39.06.L11 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 1.25mm, 2 blades with a diameter of 2.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.25.39.06.L31 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 1.25mm, 2 blades with a diameter of 2.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.25.39.06.L31 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 1.25mm, 2 blades with a diameter of 2.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.25.63.06.L11 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 1.25mm, 2 blades with a diameter of 2.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.25.63.06.L11 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 1.25mm, 2 blades with a diameter of 2.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.25.63.06.L31 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 1.25mm, 2 blades with a diameter of 2.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.25.63.06.L31 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 1.25mm, 2 blades with a diameter of 2.5 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.250.030 TS3K
Micro cutters full radius DSKM.2.250.030, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.250.050 TS3K
Micro cutters full radius DSKM.2.250.050, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.250.070 TS3K
Micro cutters full radius DSKM.2.250.070, 2 blades, 30 В° helix angle, center cutting
Paul Horn DSKM.2.30.39.06.L11 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.30.39.06.L31 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.30.63.06.L11 TS3H
Cutter shank as micro cutters for soft and hard milling with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.
Paul Horn DSKM.2.30.63.06.L11 TS3K
Cutter shank as micro cutters for soft and hard milling with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm.