Paul Horn R105.1840.3.HV7 TH35 Insert for internal turning from bore diameter of 6.8 mm to 20 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.1840.4.7 MG12 Insert for internal turning from bore diameter of 6.8 mm to 25 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.1840.4.7 TH35 Insert for internal turning from bore diameter of 6.8 mm to 25 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.1840.4.7 TI25 Insert for internal turning from bore diameter of 6.8 mm to 25 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.1840.4.7 TN35 Insert for internal turning from bore diameter of 6.8 mm to 25 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.1840.4.7.2 TH35 Insert for internal turning from bore diameter of 6.8 mm to 25 mm in length, with a corner radius of 0.1 mm. |
Paul Horn R105.1840.4.7.2 TI25 Insert for internal turning from bore diameter of 6.8 mm to 25 mm in length, with a corner radius of 0.1 mm. |
Paul Horn R105.1840.4.H.7 TF45 Insert for internal turning from bore diameter of 6.8 mm to 25 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.1840.4.H.7 TH35 Insert for internal turning from bore diameter of 6.8 mm to 25 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.1840.4.HV7 TH35 Insert for internal turning from bore diameter of 6.8 mm to 25 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.1840.5.7 MG12 Insert for internal turning from bore diameter of 6.8 mm to 30 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.1840.5.7 TH35 Insert for internal turning from bore diameter of 6.8 mm to 30 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.1840.5.7 TI25 Insert for internal turning from bore diameter of 6.8 mm to 30 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.1840.5.7 TN35 Insert for internal turning from bore diameter of 6.8 mm to 30 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.1840.5.7.2 TH35 Insert for internal turning from bore diameter of 6.8 mm to 30 mm in length, with a corner radius of 0.1 mm. |
Paul Horn R105.1840.5.7.2 TI25 Insert for internal turning from bore diameter of 6.8 mm to 30 mm in length, with a corner radius of 0.1 mm. |
Paul Horn R105.1840.5.H.7 TF45 Insert for internal turning from bore diameter of 6.8 mm to 30 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.1840.5.H.7 TH35 Insert for internal turning from bore diameter of 6.8 mm to 30 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.1840.5.HV7 TH35 Insert for internal turning from bore diameter of 6.8 mm to 30 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.1840.7.7.2 TI25 Insert for internal turning from bore diameter of 6.8 mm to 40 mm in length, with a corner radius of 0.1 mm. |
Paul Horn R105.2428.2.5 TN35 Insert to Strehlen of UN thread (part profile) from bore diameter of 5 mm with a pitch range 24-28 transition / inch. |
Paul Horn R105.2428.2.6 TN35 Insert to Strehlen of UN thread (part profile) from bore diameter 6 mm with a pitch range 24-28 transition / inch. |
Paul Horn R105.2428.3.6 TN35 Insert to Strehlen of UN thread (part profile) from bore diameter 6 mm with a pitch range 24-28 transition / inch. |
Paul Horn R105.2428.4.6 TN35 Insert to Strehlen of UN thread (part profile) from bore diameter 6 mm with a pitch range 24-28 transition / inch. |
Paul Horn R105.3013.2.3 TI25 Insert rear turning from bore diameter of 3 mm to 15 mm in length, with a corner radius of 0.1 mm. |
Paul Horn R105.3013.3.3 TI25 Insert rear turning from bore diameter of 3 mm to 20 mm in length, with a corner radius of 0.1 mm. |
Paul Horn R105.3019.2.4 TI25 Insert rear turning from bore diameter of 4 mm to 15 mm in length, with a corner radius of 0.15mm. |
Paul Horn R105.3019.4.4 TI25 Insert rear turning from bore diameter of 4 mm to 25 mm in length, with a corner radius of 0.15mm. |
Paul Horn R105.3023.3.5 TI25 Insert rear turning from bore diameter of 5 mm to 20 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.3023.5.5 TI25 Insert rear turning from bore diameter of 5 mm to 30 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.3033.3.6 TI25 Insert rear turning from bore diameter of 6 mm to 20 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.3033.5.6 TI25 Insert rear turning from bore diameter of 6 mm to 30 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.3040.3.7 TI25 Insert rear turning from bore diameter of 6.8 mm to 20 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.3040.5.7 TI25 Insert rear turning from bore diameter of 6.8 mm to 30 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.3240.2.4 TN35 Insert to Strehlen of UN thread (part profile) from bore diameter of 4 mm with a pitch range 32-40 transition / inch. |
Paul Horn R105.3240.2.5 TN35 Insert to Strehlen of UN thread (part profile) from bore diameter of 5 mm with a pitch range 32-40 transition / inch. |
Paul Horn R105.4545.2.5 TN35 Insert for interior pocketing from bore diameter 5 mm to 15 mm in length and up to 0.7 mm in depth, with a corner radius of 0.2 mm and edge angle of 45 В°. |
Paul Horn R105.4545.3.7 TN35 Insert for interior pocketing from bore diameter 7 mm to 20 mm in length and up to 0.7 mm in depth, with a corner radius of 0.2 mm and edge angle of 45 В°. |
Paul Horn R105.4713.005.1.3 AN25 Insert for internal turning and copy from bore diameter 3 mm to 10 mm in length and up to 0.4 mm in depth, with a corner radius of 0.05mm. |
Paul Horn R105.4713.005.1.3 MG12 Insert for internal turning and copy from bore diameter 3 mm to 10 mm in length and up to 0.4 mm in depth, with a corner radius of 0.05mm. |
Paul Horn R105.4713.005.2.3 AN25 Insert for internal turning and copy from bore diameter 3 mm to 15 mm in length and up to 0.4 mm in depth, with a corner radius of 0.05mm. |
Paul Horn R105.4715.005.1.2 AN25 Insert for internal turning and copy from bore diameter 2 mm to 9 mm in length and up to 0.3 mm in depth, with a corner radius of 0.05mm. |
Paul Horn R105.4715.005.2.2 AN25 Insert for internal turning and copy from bore diameter 2 mm to 12 mm in length and up to 0.3 mm in depth, with a corner radius of 0.05mm. |
Paul Horn R105.4719.1.4 TH35 Insert for internal turning and copy from bore diameter of 4 mm to 10 mm in length and up to 0.6 mm in depth, with a corner radius of 0.15mm. |
Paul Horn R105.4719.3.4 TH35 Insert for internal turning and copy from bore diameter of 4 mm to 20 mm in length and up to 0.6 mm in depth, with a corner radius of 0.15mm. |
Paul Horn R105.4719.3.4 TI25 Insert for internal turning and copy from bore diameter of 4 mm to 20 mm in length and up to 0.3 mm in depth, with a corner radius of 0.15mm. |
Paul Horn R105.4719.3.4 TN35 Insert for internal turning and copy from bore diameter of 4 mm to 20 mm in length and up to 0.3 mm in depth, with a corner radius of 0.15mm. |
Paul Horn R105.4723.2.5 TH35 Insert for internal turning and copy from bore diameter 5 mm to 15 mm in length and up to 0.8 mm in depth, with a corner radius of 0.15mm. |
Paul Horn R105.4723.4.5 TH35 Insert for internal turning and copy from bore diameter 5 mm to 25 mm in length and up to 0.8 mm in depth, with a corner radius of 0.15mm. |
Paul Horn R105.4723.4.5 TI25 Insert for internal turning and copy from bore diameter 5 mm to 25 mm in length and up to 0.5 mm in depth, with a corner radius of 0.15mm. |
Paul Horn R105.4723.4.5 TN35 Insert for internal turning and copy from bore diameter 5 mm to 25 mm in length and up to 0.5 mm in depth, with a corner radius of 0.15mm. |
Paul Horn R105.4733.3.6 TH35 Insert for internal turning and copy from bore diameter 6 mm to 20 mm in length and up to 1.8 mm in depth, with a corner radius of 0.15 mm. |
Paul Horn R105.4733.5.6 TH35 Insert for internal turning and copy from bore diameter 6 mm to 30 mm in length and up to 1.8 mm in depth, with a corner radius of 0.15mm. |
Paul Horn R105.4733.5.6 TN35 Insert for internal turning and copy from bore diameter 6 mm to 30 mm in length and up to 1.8 mm in depth, with a corner radius of 0.15mm. |
Paul Horn R105.4733.5.6.2 TH35 Insert for internal turning and copy from bore diameter 6 mm to 30 mm in length and up to 1.8 mm in depth, with a corner radius of 0.1 mm. |
Paul Horn R105.4733.5.6.2 TI25 Insert for internal turning and copy from bore diameter 6 mm to 30 mm in length and up to 1.8 mm in depth, with a corner radius of 0.1 mm. |
Paul Horn R105.5519.2.6 TN35 Insert to Strehlen BSW / BSF (solid profile) from bore diameter 6 mm to 15 mm in length at a pitch of 19 transition / inch. |
Paul Horn R105.5519.3.6 TN35 Insert to Strehlen BSW / BSF (solid profile) from bore diameter 6 mm to 20 mm in length at a pitch of 19 transition / inch. |
Paul Horn R105.5520.2.4 TN35 Insert to Strehlen BSW / BSF (solid profile) from bore diameter of 4 mm to 15 mm in length at a pitch of 20 transition / inch. |
Paul Horn R105.5520.2.6 TN35 Insert to Strehlen BSW / BSF (solid profile) from bore diameter 6 mm to 15 mm in length at a pitch of 20 transition / inch. |
Paul Horn R105.5522.2.6 TN35 Insert to Strehlen BSW / BSF (solid profile) from bore diameter 6 mm to 15 mm in length at a pitch of 22 transition / inch. |
Paul Horn R105.5522.3.6 TN35 Insert to Strehlen BSW / BSF (solid profile) from bore diameter 6 mm to 20 mm in length at a pitch of 22 transition / inch. |
Paul Horn R105.5524.2.5 TN35 Insert to Strehlen BSW / BSF (solid profile) from bore diameter 5 mm to 15 mm in length at a pitch of 24 speed / inch. |
Paul Horn R105.5524.2.6 TN35 Insert to Strehlen BSW / BSF (solid profile) from bore diameter 6 mm to 15 mm in length at a pitch of 24 speed / inch. |
Paul Horn R105.5524.3.6 TN35 Insert to Strehlen BSW / BSF (solid profile) from bore diameter 6 mm to 20 mm in length at a pitch of 24 speed / inch. |
Paul Horn R105.5526.2.5 TN35 Insert to Strehlen BSW / BSF (solid profile) from bore diameter 5 mm to 15 mm in length at a pitch of 26 transition / inch. |
Paul Horn R105.5526.2.6 TN35 Insert to Strehlen BSW / BSF (solid profile) from bore diameter 6 mm to 15 mm in length at a pitch of 26 transition / inch. |
Paul Horn R105.5526.3.6 TN35 Insert to Strehlen BSW / BSF (solid profile) from bore diameter 6 mm to 20 mm in length at a pitch of 26 transition / inch. |
Paul Horn R105.5528.2.5 TN35 Insert to Strehlen BSW / BSF (solid profile) from bore diameter 5 mm to 15 mm in length at a pitch of 28 transition / inch. |
Paul Horn R105.5528.2.6 TN35 Insert to Strehlen BSW / BSF (solid profile) from bore diameter 6 mm to 15 mm in length at a pitch of 28 transition / inch. |
Paul Horn R105.5528.3.6 TN35 Insert to Strehlen BSW / BSF (solid profile) from bore diameter 6 mm to 20 mm in length at a pitch of 28 transition / inch. |
Paul Horn R105.8V10.1.8 TI25 Insert to Grooving with radius 0.5 mm from minimum Einstechdurchmesser of 8 mm with 1 mm width, maximum penetration depth of 2 mm. |
Paul Horn R105.8V10.2.8 TI25 Insert to Grooving with radius 0.5 mm from minimum Einstechdurchmesser of 8 mm with 1 mm width, maximum penetration depth of 2 mm. |
Paul Horn R105.8V16.1.8 TI25 Insert to Grooving with radius 0.8 mm from minimum Einstechdurchmesser of 8 mm with 1.6 mm width, maximum penetration depth of 3 mm. |
Paul Horn R105.8V16.2.8 TI25 Insert to Grooving with radius 0.8 mm from minimum Einstechdurchmesser of 8 mm with 1.6 mm width, maximum penetration depth of 3 mm. |
Paul Horn R105.8V20.1.8 TI25 Insert to Grooving with radius 1 mm from minimum Einstechdurchmesser of 8 mm with 2 mm width, maximum penetration depth of 4 mm. |
Paul Horn R105.8V20.2.8 TI25 Insert to Grooving with radius 1 mm from minimum Einstechdurchmesser of 8 mm with 2 mm width, maximum penetration depth of 4 mm. |
Paul Horn R105.8V25.1.8 TI25 Insert to Grooving with radius 1.25mm from minimum Einstechdurchmesser of 8 mm with 2.5 mm width, maximum penetration depth of 5 mm. |
Paul Horn R105.8V25.2.8 TI25 Insert to Grooving with radius 1.25mm from minimum Einstechdurchmesser of 8 mm with 2.5 mm width, maximum penetration depth of 5 mm. |
Paul Horn R105.8V30.1.8 TI25 Insert to Grooving with radius 1.5 mm from minimum Einstechdurchmesser of 8 mm with 3 mm width, maximum penetration depth of 6 mm. |
Paul Horn R105.8V30.2.8 TI25 Insert to Grooving with radius 1.5 mm from minimum Einstechdurchmesser of 8 mm with 3 mm width, maximum penetration depth of 6 mm. |
Paul Horn R105.9013.000.0.02 AN25 Insert for internal turning from bore diameter of 0.2 mm |
Paul Horn R105.9013.000.0.03 AN25 Insert for internal turning from bore diameter of 0.3 mm |
Paul Horn R105.9013.000.0.05 AN25 Insert for internal turning from bore diameter of 0.5 mm |
Paul Horn R105.9013.000.0.05 MG12 Insert for internal turning from bore diameter of 0.5 mm |
Paul Horn R105.9013.000.0.07 AN25 Insert for internal turning from bore diameter of 0.7 mm |
Paul Horn R105.9013.000.0.1 AN25 Insert type, to bore turning from 1.0 mm |
Paul Horn R105.9013.000.0.15 AN25 Insert type, to bore turning from 1.5 mm |
Paul Horn R105.9013.000.0.2 AN25 Insert type coated, |
Paul Horn R105.9013.000.0.25 AN25 Insert type coated, |
Paul Horn R105.9013.000.1.15 AN25 Insert type, to bore turning from 1.5 mm |
Paul Horn R105.9013.000.1.3 AN25 Insert type coated, |
Paul Horn R105.9013.000.2.1 AN25 Insert type, to bore turning from 1.0 mm |
Paul Horn R105.9013.000.2.2 AN25 Insert type coated, |
Paul Horn R105.9013.000.2.25 AN25 Insert type coated, |
Paul Horn R105.9013.000.2.25 MG12 Insert type for internal turning from bore diameter 2.0 mm |
Paul Horn R105.9013.000.3.25 AN25 Insert type coated, |
Paul Horn R105.9013.000.3.3 AN25 Insert type coated, |
Paul Horn R105.9013.003.0.1 AN25 Insert type, to bore turning from 1.0 mm |
Paul Horn R105.9013.003.0.15 AN25 Insert type, to bore turning from 1.5 mm |
Paul Horn R105.9013.003.0.2 AN25 Insert type coated, |
Paul Horn R105.9013.003.0.25 AN25 Insert type coated, |
Paul Horn R105.9013.003.1.15 AN25 Insert type, to bore turning from 1.5 mm |
Paul Horn R105.9013.003.1.3 AN25 Insert type coated, |
Paul Horn R105.9013.003.2.1 AN25 Insert type, to bore turning from 1.0 mm |
Paul Horn R105.9013.003.2.2 AN25 Insert type coated, |
Paul Horn R105.9013.003.2.25 AN25 Insert type, coated, for internal turning from bore diameter 2.5 mm |
Paul Horn R105.9013.003.2.25 MG12 Insert type, for internal turning from bore diameter 2.5 mm |
Paul Horn R105.9013.003.3.25 AN25 Insert type coated, |
Paul Horn R105.9013.003.3.3 AN25 Insert type coated, |
Paul Horn R105.9013.01.1.3 TH35 Insert for internal turning from bore diameter 3 mm to 10 mm in length, with a corner radius of 0.1 mm. |
Paul Horn R105.9013.01.2.3 TH35 Insert for internal turning from bore diameter 3 mm to 15 mm in length, with a corner radius of 0.1 mm. |
Paul Horn R105.9013.1.3 TN35 Insert for internal turning from bore diameter 3 mm to 10 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.9013.2.3 TN35 Insert for internal turning from bore diameter 3 mm to 15 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.9019.000.1.4 AN25 Insert type coated, |
Paul Horn R105.9019.003.1.4 AN25 Insert type coated, |
Paul Horn R105.9019.003.3.4 AN25 Insert type coated, |
Paul Horn R105.9019.01.1.4 TH35 Insert for internal turning from bore diameter of 4 mm to 10 mm in length, with a corner radius of 0.1 mm. |
Paul Horn R105.9019.01.2.4 TH35 Insert for internal turning from bore diameter of 4 mm to 15 mm in length, with a corner radius of 0.1 mm. |
Paul Horn R105.9019.01.3.4 TH35 Insert for internal turning from bore diameter of 4 mm to 20 mm in length, with a corner radius of 0.1 mm. |
Paul Horn R105.9019.1.4 TN35 Insert for internal turning from bore diameter of 4 mm to 10 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.9019.2.4 TN35 Insert for internal turning from bore diameter of 4 mm to 15 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.9023.000.1.5 AN25 Insert type coated, |
Paul Horn R105.9023.000.3.5 AN25 Insert type coated, |
Paul Horn R105.9023.000.5.5 AN25 Insert type coated, |
Paul Horn R105.9023.003.1.5 AN25 Insert type coated, |
Paul Horn R105.9023.003.3.5 AN25 Insert type coated, |
Paul Horn R105.9023.003.5.5 AN25 Insert type coated, |
Paul Horn R105.9023.01.1.5 TH35 Insert for internal turning from bore diameter 5 mm to 10 mm in length, with a corner radius of 0.1 mm. |
Paul Horn R105.9023.01.2.5 TH35 Insert for internal turning from bore diameter 5 mm to 15 mm in length, with a corner radius of 0.1 mm. |
Paul Horn R105.9023.01.3.5 TH35 Insert for internal turning from bore diameter 5 mm to 20 mm in length, with a corner radius of 0.1 mm. |
Paul Horn R105.9023.01.4.5 TH35 Insert for internal turning from bore diameter 5 mm to 25 mm in length, with a corner radius of 0.1 mm. |
Paul Horn R105.9023.1.5 TH35 Insert for internal turning from bore diameter 5 mm to 10 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.9023.1.5 TN35 Insert for internal turning from bore diameter 5 mm to 10 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.9023.2.5 TN35 Insert for internal turning from bore diameter 5 mm to 15 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.9023.3.5 TN35 Insert for internal turning from bore diameter 5 mm to 20 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.9033.1.6 TH35 Insert for internal turning from bore diameter 6 mm to 10 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.9033.2.6 TH35 Insert for internal turning from bore diameter 6 mm to 15 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.9033.3.6 TH35 Insert for internal turning from bore diameter 6 mm to 20 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.9033.4.6 TH35 Insert for internal turning from bore diameter 6 mm to 25 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.9033.5.6 TH35 Insert for internal turning from bore diameter 6 mm to 30 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R105.LEHR.H.01 Plate to set the cutter on center |
Paul Horn R105.NP18.2.6 TN35 Insert to Strehlen of NPT / NPTF thread (part profile) from bore diameter 6 mm to 15 mm in length at a pitch of 18 transition / inch. |
Paul Horn R105.NP18.3.6 TH35 Insert to Strehlen of NPT / NPTF thread (part profile) from bore diameter 6 mm to 20 mm in length at a pitch of 18 transition / inch. |
Paul Horn R105.NP18.3.6 TN35 Insert to Strehlen of NPT / NPTF thread (part profile) from bore diameter 6 mm to 20 mm in length at a pitch of 18 transition / inch. |
Paul Horn R105.NP18.4.6 TH35 Insert to Strehlen of NPT / NPTF thread (part profile) from bore diameter 6 mm to 25 mm in length at a pitch of 18 transition / inch. |
Paul Horn R105.NP18.4.6 TN35 Insert to Strehlen of NPT / NPTF thread (part profile) from bore diameter 6 mm to 25 mm in length at a pitch of 18 transition / inch. |
Paul Horn R105.NP27.2.6 TN35 Insert to Strehlen of NPT / NPTF thread (part profile) from bore diameter 6 mm to 15 mm in length at a pitch of 27 speed / inch. |
Paul Horn R105.NP27.3.6 TH35 Insert to Strehlen of NPT / NPTF thread (part profile) from bore diameter 6 mm to 20 mm in length at a pitch of 27 speed / inch. |
Paul Horn R105.NP27.3.6 TI25 Insert TiCN coated |
Paul Horn R105.NP27.3.6 TN35 Insert to Strehlen of NPT / NPTF thread (part profile) from bore diameter 6 mm to 20 mm in length at a pitch of 27 speed / inch. |
Paul Horn R105.NP27.4.6 TH35 Insert to Strehlen of NPT / NPTF thread (part profile) from bore diameter 6 mm to 25 mm in length at a pitch of 27 speed / inch. |
Paul Horn R105.NP27.4.6 TN35 Insert to Strehlen of NPT / NPTF thread (part profile) from bore diameter 6 mm to 25 mm in length at a pitch of 27 speed / inch. |
Paul Horn R105.VPM3.2.3 TH35 Insert for chasing of metric ISO thread (solid profile) from bore diameter 2.4 mm to 9 mm in length at a pitch of 0.5 mm. |
Paul Horn R105.VPM3.4.3 TH35 Insert for chasing of metric ISO thread (solid profile) from bore diameter 2.4 mm to 12 mm in length at a pitch of 0.5 mm. |
Paul Horn R105.VPM4.2.4 TH35 Insert for chasing of metric ISO thread (solid profile) from bore diameter 3.2 mm to 15 mm in length at a pitch of 0.7 mm. |
Paul Horn R105.VPM4.3.4 TH35 Insert for chasing of metric ISO thread (solid profile) from bore diameter 3.2 mm to 20 mm in length at a pitch of 0.7 mm. |
Paul Horn R105.VPM5.2.5 TH35 Insert for chasing of metric ISO thread (solid profile) from bore diameter 4.1 mm to 15 mm in length at a pitch of 0.8 mm. |
Paul Horn R105.VPM5.4.5 TH35 Insert for chasing of metric ISO thread (solid profile) from bore diameter 4.1 mm to 25 mm in length at a pitch of 0.8 mm. |
Paul Horn R105.VPM6.3.6 TH35 Insert for chasing of metric ISO thread (solid profile) from bore diameter 4.9 mm to 20 mm in length at a pitch of 1 mm. |
Paul Horn R105.VPM6.4.6 Insert for chasing of metric ISO thread (solid profile) from bore diameter 4.9 mm to 25 mm in length at a pitch of 1 mm. |
Paul Horn R105.VPM6.5.6 TH35 Insert for chasing of metric ISO thread (solid profile) from bore diameter 4.9 mm to 30 mm in length at a pitch of 1 mm. |
Paul Horn R105.VPM8.3.8 TH35 Insert for chasing of metric ISO thread (solid profile) from bore diameter 6.6 mm to 20 mm in length at a pitch of 1.25mm. |
Paul Horn R105.VPM8.5.8 TH35 Insert for chasing of metric ISO thread (solid profile) from bore diameter 6.6 mm to 30 mm in length at a pitch of 1.25mm. |
Paul Horn R106.0070.2.00 TH35 The insert with a cutting width of 0.74 mm is suitable for penetration and removing inner contours with up to 0.8 mm deep. |
Paul Horn R106.0100.2.00 TH35 The insert with a cutting width of 1 mm is suitable for penetration and removing inner contours with up to 0.8 mm deep. |
Paul Horn R106.0150.2.00 TH35 The insert with a cutting width of 1.5 mm is suitable for penetration and removing inner contours with up to 0.8 mm deep. |
Paul Horn R106.1831.1.005 TH35 Insert for internal turning from bore diameter 6 mm, with a corner radius of 0.05mm. |
Paul Horn R106.1831.1.02 TH35 Insert for internal turning from bore diameter 6 mm, with a corner radius of 0.2 mm. |
Paul Horn R106.1831.1.04 TH35 Insert for internal turning from bore diameter 6 mm, with a corner radius of 0.4 mm. |
Paul Horn R106.4545.1.02 TH35 The insert is suitable for chamfering and back turning with up to 0.6 mm deep. |
Paul Horn R107.0100.1.00 The insert TH35 with a cutting width of 1 mm is suitable for penetration of up to 1 mm depth. |
Paul Horn R107.0100.2.00 The insertTH35 TH35 with a cutting width of 1 mm is suitable for penetration of up to 2 mm depth. |
Paul Horn R107.0150.1.00 The insert TH35 with a cutting width of 1.5 mm is suitable for penetration of up to 1 mm depth. |
Paul Horn R107.0150.2.01 The insertTH35 TH35 with a cutting width of 1.5 mm is suitable for penetration of up to 2 mm depth. |
Paul Horn R107.0200.2.00 The insert R107.0200.2.02TH35 TH35 with a cutting width of 2 mm is suitable for penetration of up to 2 mm depth. |
Paul Horn R107.0205.1.01 TH35 Insert for chasing of metric ISO thread (part profile) from bore diameter 7 mm with a pitch from 0.5 to 0.75 mm. |
Paul Horn R107.0510.1.01 TH35 Insert for chasing of metric ISO thread (part profile) from bore diameter 7 mm with a pitch from 1.0 to 1.25 mm. |
Paul Horn R107.0537.02.B CB10 Insert CBN equipped for hard internal turning from bore diameter 6.8 mm, with a corner radius of 0.2 mm. |
Paul Horn R107.0815.1.01 TH35 Insert for chasing of metric ISO thread (part profile) from bore diameter 7 mm with a pitch from 1.5 to 1.75 mm. |
Paul Horn R107.1837.02 TH35 The insert is suitable for turning internal contours. |
Paul Horn R107.1837.04 TH35 The insert is suitable for turning internal contours. |
Paul Horn R107.4545.1.02 TH35 The insert is suitable for penetration and removing inner contours with up to 0.8 mm deep. |
Paul Horn R108.0004.08 MG12 Insert deep for the cutting of grooves from bore diameter 8 mm with 0.8 mm width, full radius 0.4 mm and a maximum of 1 mm. |
Paul Horn R108.0004.08 TH35 Insert deep for the cutting of grooves from bore diameter 8 mm with 0.8 mm width, full radius 0.4 mm and a maximum of 1 mm. |
Paul Horn R108.0004.08 TN35 Insert deep for the cutting of grooves from bore diameter 8 mm with 0.8 mm width, full radius 0.4 mm and a maximum of 1 mm. |
Paul Horn R108.0006.12 MG12 Insert for cutting of grooves from bore diameter 8 mm with 1.2 mm width, full radius 0.6 mm and a maximum depth of 1 mm. |
Paul Horn R108.0006.12 TH35 Insert deep for the cutting of grooves from bore diameter 8 mm with 1.2 mm width, full radius 0.6 mm and a maximum of 1 mm. |
Paul Horn R108.0006.12 TN35 Insert deep for the cutting of grooves from bore diameter 8 mm with 1.2 mm width, full radius 0.6 mm and a maximum of 1 mm. |
Paul Horn R108.0009.18 MG12 Insert deep for the cutting of grooves from bore diameter 8 mm with 1.8 mm width, full radius of 0.9 mm and a maximum of 1 mm. |
Paul Horn R108.0009.18 TH35 Insert deep for the cutting of grooves from bore diameter 8 mm with 1.8 mm width, full radius of 0.9 mm and a maximum of 1 mm. |
Paul Horn R108.0009.18 TI25 Insert deep for the cutting of grooves from bore diameter 8 mm with 1.8 mm width, full radius of 0.9 mm and a maximum of 1 mm. |
Paul Horn R108.0009.18 TN35 Insert deep for the cutting of grooves from bore diameter 8 mm with 1.8 mm width, full radius of 0.9 mm and a maximum of 1 mm. |
Paul Horn R108.0070.00 TH35 Insert deep for piercing of Seegerringnuten DIN 471/472 from bore diameter 8 mm with 0.74 mm width, nominal width 0.7 mm and a maximum of 1 mm. |
Paul Horn R108.0070.00 TN35 Insert deep for piercing of Seegerringnuten DIN 471/472 from bore diameter 8 mm with 0.74 mm width, nominal width 0.7 mm and a maximum of 1 mm. |
Paul Horn R108.0080.00 TH35 Insert deep for piercing of Seegerringnuten DIN 471/472 from bore diameter 8 mm with 0.84 mm width, nominal width of 0.8 mm and a maximum of 1 mm. |
Paul Horn R108.0080.00 TN35 Insert deep for piercing of Seegerringnuten DIN 471/472 from bore diameter 8 mm with 0.84 mm width, nominal width of 0.8 mm and a maximum of 1 mm. |
Paul Horn R108.0090.00 TH35 Insert deep for piercing of Seegerringnuten DIN 471/472 from bore diameter 8 mm with 0.94 mm width, nominal width of 0.9 mm and a maximum of 1 mm. |
Paul Horn R108.0090.00 TN35 Insert deep for piercing of Seegerringnuten DIN 471/472 from bore diameter 8 mm with 0.94 mm width, nominal width of 0.9 mm and a maximum of 1 mm. |
Paul Horn R108.0110.00 MG12 Insert deep for piercing of Seegerringnuten DIN 471/472 from bore diameter 8 mm with 1.19 width, nominal width 1.1 mm and a maximum of 1 mm. |
Paul Horn R108.0110.00 TH35 Insert deep for piercing of Seegerringnuten DIN 471/472 from bore diameter 8 mm with 1.19 width, nominal width 1.1 mm and a maximum of 1 mm. |
Paul Horn R108.0110.00 TN35 Insert deep for piercing of Seegerringnuten DIN 471/472 from bore diameter 8 mm with 1.19 width, nominal width 1.1 mm and a maximum of 1 mm. |
Paul Horn R108.0130.00 MG12 Insert deep for piercing of Seegerringnuten DIN 471/472 from bore diameter 8 mm with 1.39 mm width, nominal width of 1.3 mm and a maximum of 1 mm. |
Paul Horn R108.0130.00 TH35 Insert deep for piercing of Seegerringnuten DIN 471/472 from bore diameter 8 mm 1.39 mm width, nominal width of 1.3 mm and a maximum of 1 mm. |
Paul Horn R108.0130.00 TN35 Insert deep for piercing of Seegerringnuten DIN 471/472 from bore diameter 8 mm 1.39 mm width, nominal width of 1.3 mm and a maximum of 1 mm. |
Paul Horn R108.0150.00 MG12 Insert deep grooves for insertion from bore diameter 8 mm with 1.5 mm width, corner radius of 0 mm and a maximum of 1 mm. |
Paul Horn R108.0150.00 TH35 Insert deep grooves for insertion from bore diameter 8 mm with 1.5 mm width, corner radius of 0 mm and a maximum of 1 mm. |
Paul Horn R108.0150.00 TN35 Insert deep grooves for insertion from bore diameter 8 mm with 1.5 mm width, corner radius of 0 mm and a maximum of 1 mm. |
Paul Horn R108.0150.02 MG12 Insert for insertion grooves from bore diameter 8 mm with 1.5 mm width, corner radius 0.2 mm and a maximum depth of 1 mm. |
Paul Horn R108.0150.02 TH35 Insert deep grooves for insertion from bore diameter 8 mm with 1.5 mm width, corner radius 0.2 mm and a maximum of 1 mm. |
Paul Horn R108.0150.02 TI25 Insert deep grooves for insertion from bore diameter 8 mm with 1.5 mm width, corner radius 0.2 mm and a maximum of 1 mm. |
Paul Horn R108.0150.02 TN35 Insert deep grooves for insertion from bore diameter 8 mm with 1.5 mm width, corner radius 0.2 mm and a maximum of 1 mm. |
Paul Horn R108.0160.00 MG12 Insert deep for piercing of Seegerringnuten DIN 471/472 from bore diameter 8 mm with 1.69 mm width, nominal width of 1.6 mm and a maximum of 1 mm. |
Paul Horn R108.0160.00 TH35 Insert deep for piercing of Seegerringnuten DIN 471/472 from bore diameter 8 mm with 1.69 mm width, nominal width of 1.6 mm and a maximum of 1 mm. |
Paul Horn R108.0160.00 TN35 Insert deep for piercing of Seegerringnuten DIN 471/472 from bore diameter 8 mm with 1.69 mm width, nominal width of 1.6 mm and a maximum of 1 mm. |
Paul Horn R108.0200.00 MG12 Insert deep grooves for insertion from bore diameter 8 mm with 2 mm width, corner radius of 0 mm and a maximum of 1 mm. |
Paul Horn R108.0200.00 TH35 Insert deep grooves for insertion from bore diameter 8 mm with 2 mm width, corner radius of 0 mm and a maximum of 1 mm. |
Paul Horn R108.0200.00 TN35 Insert deep grooves for insertion from bore diameter 8 mm with 2 mm width, corner radius of 0 mm and a maximum of 1 mm. |
Paul Horn R108.0205.01 MG12 Insert for chasing of metric ISO thread (part profile) from bore diameter 8 mm with a pitch of 0.5-0.75 mm. |
Paul Horn R108.0205.01 TH35 Insert for chasing of metric ISO thread (part profile) from bore diameter 8 mm with a pitch of 0.5-0.75 mm. |
Paul Horn R108.0205.01 TN35 Insert for chasing of metric ISO thread (part profile) from bore diameter 8 mm with a pitch of 0.5-0.75 mm. |
Paul Horn R108.0510.01 MG12 Insert for chasing of metric ISO thread (part profile) from bore diameter 8 mm with a gradient of 1-1.25 mm. |
Paul Horn R108.0510.01 TH35 Insert for chasing of metric ISO thread (part profile) from bore diameter 8 mm with a gradient of 1-1.25 mm. |
Paul Horn R108.0510.01 TI25 Insert for chasing of metric ISO thread (part profile) from bore diameter 8 mm with a gradient of 1-1.25 mm. |
Paul Horn R108.0510.01 TN35 Insert for chasing of metric ISO thread (part profile) from bore diameter 8 mm with a gradient of 1-1.25 mm. |
Paul Horn R108.0547.03.B CB10 Insert CBN equipped for hard internal turning and copying from bore diameter 7.8 mm, with a corner radius of 0.3 mm. |
Paul Horn R108.0810.45 MG12 Insert for preparting and chamfering from bore diameter 8 mm with 1 mm width, maximum 1.5 mm deep. |
Paul Horn R108.0810.45 TI25 Insert to preparting and chamfering from bore diameter 8 mm with 1 mm width, maximum 1.5 mm deep. |
Paul Horn R108.0810.45 TN35 Insert for internal turning and copying from bore diameter 8 mm, with a corner radius of 0 mm. |
Paul Horn R108.0815.01 MG12 Insert for chasing of metric ISO thread (part profile) from bore diameter 8 mm with a pitch of 1.5-1.75 mm. |
Paul Horn R108.0815.01 TH35 Insert for chasing of metric ISO thread (part profile) from bore diameter 8 mm with a pitch of 1.5-1.75 mm. |
Paul Horn R108.0815.01 TN35 Insert for chasing of metric ISO thread (part profile) from bore diameter 8 mm with a pitch of 1.5-1.75 mm. |
Paul Horn R108.1846.02 MG12 Insert for internal turning and copying from bore diameter 7.8 mm, with a corner radius of 0.2 mm. |
Paul Horn R108.1846.02 TH35 Insert for internal turning and copying from bore diameter 7.8 mm, with a corner radius of 0.2 mm. |
Paul Horn R108.1846.02 TI25 Insert for internal turning and copying from bore diameter 7.8 mm, with a corner radius of 0.2 mm. |
Paul Horn R108.1846.02 TN35 Insert for internal turning and copying from bore diameter 7.8 mm, with a corner radius of 0.2 mm. |
Paul Horn R108.3046.02 TH35 Insert for internal turning and copying from bore diameter 7.8 mm, with a corner radius of 0.2 mm. |
Paul Horn R108.3046.02 TN35 Insert for internal turning and copying from bore diameter 7.8 mm, with a corner radius of 0.2 mm. |
Paul Horn R108.4545.02 TA45 Insert for interior pocketing from bore diameter 7.8 mm up to 1.4 mm in depth, with a corner radius of 0.2 mm and edge angle of 45 В°. |
Paul Horn R108.4545.02 TI25 Insert for interior pocketing from bore diameter 7.8 mm up to 1.4 mm in depth, with a corner radius of 0.2 mm and edge angle of 45 В°. |
Paul Horn R108.4545.02 TN35 Insert for interior pocketing from bore diameter 7.8 mm up to 1.4 mm in depth, with a corner radius of 0.2 mm and edge angle of 45 В°. |
Paul Horn R108.4748.01 TH35 Insert for internal turning and copying from bore diameter 7.8 mm, with a corner radius of 0.1 mm. |
Paul Horn R108.4748.02 TH35 Insert for internal turning and copying from bore diameter 7.8 mm, with a corner radius of 0.2 mm. |
Paul Horn R108.4748.02 TN35 Insert for internal turning and copying from bore diameter 7.8 mm, with a corner radius of 0.2 mm. |
Paul Horn R108.4748.04 TH35 Insert for internal turning and copying from bore diameter 7.8 mm, with a corner radius of 0.4 mm. |
Paul Horn R108.NP14.02 TN35 Insert to Strehlen of NPT (solid profile) from bore diameter 8 mm with a pitch of 14 transition / inch. |
Paul Horn R108.NP18.02 TN35 Insert to Strehlen of NPT (solid profile) from bore diameter 8 mm with a pitch of 18 transition / inch. |
Paul Horn R108.NP27.02 TN35 Insert to Strehlen of NPT (solid profile) from bore diameter 8 mm with a pitch of 27 speed / inch. |
Paul Horn R108.PG18.02 TN35 Insert to Strehlen of conduit threads (PG Full Profile) from bore diameter 8 mm with a pitch of 18 transition / inch. |
Paul Horn R108.PG20.02 TN35 Insert to Strehlen of conduit threads (PG Full Profile) from bore diameter 8 mm with a pitch of 20 transition / inch. |
Paul Horn R109.0005.4.6 TH35 Insert deep for the cutting of grooves from bore diameter 6 mm to 25 mm in length with 1 mm width, full radius 0.5 mm and a maximum of 1.8 mm. |
Paul Horn R109.0005.6.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 35 mm in length with 1 mm width, full radius 0.5 mm and a maximum of 2.5 mm. |
Paul Horn R109.0007.4.6 TH35 Insert deep for the cutting of grooves from bore diameter 6 mm to 25 mm length with 1.5 mm width, full radius 0.75 mm and a maximum of 1.8 mm. |
Paul Horn R109.0007.6.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 35 mm length with 1.5 mm width, full radius 0.75 mm and a maximum of 2.5 mm. |
Paul Horn R109.0010.4.6 TH35 Insert deep for the cutting of grooves from bore diameter 6 mm to 25 mm long with 2 mm wide, full radius 1 mm and a maximum of 1.8 mm. |
Paul Horn R109.0010.6.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 35 mm long with 2 mm wide, full radius 1 mm and a maximum of 2.5 mm. |
Paul Horn R109.0100.1.6 TH35 Insert deep for the cutting of grooves from bore diameter 6 mm to 10 mm in length with 1 mm width, corner radius of 0 mm and a maximum of 1.8 mm. |
Paul Horn R109.0100.1.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 10 mm in length with 1 mm width, corner radius of 0 mm and a maximum of 2.5 mm. |
Paul Horn R109.0100.2.6 TH35 Insert for the cutting of grooves from bore diameter 6 mm to 15 mm in length with 1 mm width, corner radius of 0 mm and a maximum of 1.8 mm deep. |
Paul Horn R109.0100.2.7 TH35 Insert for the cutting of grooves from bore diameter 7 mm to 15 mm in length with 1 mm width, corner radius of 0 mm and a maximum of 2.5 mm deep. |
Paul Horn R109.0100.3.6 TH35 Insert deep for the cutting of grooves from bore diameter 6 mm to 20 mm in length with 1 mm width, corner radius of 0 mm and a maximum of 1.8 mm. |
Paul Horn R109.0100.3.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 20 mm in length with 1 mm width, corner radius of 0 mm and a maximum of 2.5 mm. |
Paul Horn R109.0100.4.6 TH35 Insert for the cutting of grooves from bore diameter 6 mm to 25 mm in length with 1 mm width, corner radius of 0 mm and a maximum of 1.8 mm deep. |
Paul Horn R109.0100.4.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 25 mm in length with 1 mm width, corner radius of 0 mm and a maximum of 2.5 mm. |
Paul Horn R109.0100.5.6 TH35 Insert for the cutting of grooves from bore diameter 6 mm to 30 mm in length with 1 mm width, corner radius of 0 mm and a maximum of 1.8 mm deep. |
Paul Horn R109.0100.5.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 30 mm in length with 1 mm width, corner radius of 0 mm and a maximum of 2.5 mm. |
Paul Horn R109.0100.6.6 TH35 Insert for the cutting of grooves from bore diameter 6 mm to 35 mm in length with 1 mm width, corner radius of 0 mm and a maximum of 1.8 mm deep. |
Paul Horn R109.0100.6.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 35 mm in length with 1 mm width, corner radius of 0 mm and a maximum of 2.5 mm. |
Paul Horn R109.0150.1.6 TH35 Insert deep for the cutting of grooves from bore diameter 6 mm to 10 mm length with 1.5 mm width, corner radius of 0 mm and a maximum of 1.8 mm. |
Paul Horn R109.0150.1.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 10 mm length with 1.5 mm width, corner radius of 0 mm and a maximum of 2.5 mm. |
Paul Horn R109.0150.2.6 TH35 Insert for the cutting of grooves from bore diameter 6 mm to 15 mm length with 1.5 mm width, corner radius of 0 mm and a maximum of 1.8 mm deep. |
Paul Horn R109.0150.2.7 TH35 Insert for the cutting of grooves from bore diameter 7 mm to 15 mm length with 1.5 mm width, corner radius of 0 mm and a maximum of 2.5 mm deep. |
Paul Horn R109.0150.3.6 TH35 Insert deep for the cutting of grooves from bore diameter 6 mm to 20 mm length with 1.5 mm width, corner radius of 0 mm and a maximum of 1.8 mm. |
Paul Horn R109.0150.3.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 20 mm length with 1.5 mm width, corner radius of 0 mm and a maximum of 2.5 mm. |
Paul Horn R109.0150.4.6 TH35 Insert for the cutting of grooves from bore diameter 6 mm to 25 mm length with 1.5 mm width, corner radius of 0 mm and a maximum of 1.8 mm deep. |
Paul Horn R109.0150.4.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 25 mm length with 1.5 mm width, corner radius of 0 mm and a maximum of 2.5 mm. |
Paul Horn R109.0150.5.6 TH35 Insert for the cutting of grooves from bore diameter 6 mm to 30 mm length with 1.5 mm width, corner radius of 0 mm and a maximum of 1.8 mm deep. |
Paul Horn R109.0150.5.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 30 mm length with 1.5 mm width, corner radius of 0 mm and a maximum of 2.5 mm. |
Paul Horn R109.0150.6.6 TH35 Insert for the cutting of grooves from bore diameter 6 mm to 35 mm length with 1.5 mm width, corner radius of 0 mm and a maximum of 1.8 mm deep. |
Paul Horn R109.0150.6.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 35 mm length with 1.5 mm width, corner radius of 0 mm and a maximum of 2.5 mm. |
Paul Horn R109.0200.1.6 TH35 Insert deep for the cutting of grooves from bore diameter 6 mm to 10 mm in length with 2 mm width, corner radius of 0 mm and a maximum of 1.8 mm. |
Paul Horn R109.0200.1.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 10 mm in length with 2 mm width, corner radius of 0 mm and a maximum of 2.5 mm. |
Paul Horn R109.0200.2.6 TH35 Insert for the cutting of grooves from bore diameter 6 mm to 15 mm in length with 2 mm width, corner radius of 0 mm and a maximum of 1.8 mm deep. |
Paul Horn R109.0200.2.7 TH35 Insert for the cutting of grooves from bore diameter 7 mm to 15 mm in length with 2 mm width, corner radius of 0 mm and a maximum of 2.5 mm deep. |
Paul Horn R109.0200.3.6 TH35 Insert deep for the cutting of grooves from bore diameter 6 mm to 20 mm in length with 2 mm width, corner radius of 0 mm and a maximum of 1.8 mm. |
Paul Horn R109.0200.3.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 20 mm in length with 2 mm width, corner radius of 0 mm and a maximum of 2.5 mm. |
Paul Horn R109.0200.4.6 TH35 Insert for the cutting of grooves from bore diameter 6 mm to 25 mm in length with 2 mm width, corner radius of 0 mm and a maximum of 1.8 mm deep. |
Paul Horn R109.0200.4.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 25 mm in length with 1 mm width, corner radius of 0 mm and a maximum of 2.5 mm. |
Paul Horn R109.0200.5.6 TH35 Insert for the cutting of grooves from bore diameter 6 mm to 30 mm in length with 2 mm width, corner radius of 0 mm and a maximum of 1.8 mm deep. |
Paul Horn R109.0200.5.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 30 mm in length with 2 mm width, corner radius of 0 mm and a maximum of 2.5 mm. |
Paul Horn R109.0200.6.6 TH35 Insert for the cutting of grooves from bore diameter 6 mm to 35 mm in length with 2 mm width, corner radius of 0 mm and a maximum of 1.8 mm deep. |
Paul Horn R109.0200.6.7 TH35 Insert deep for the cutting of grooves from bore diameter 7 mm to 35 mm in length with 2 mm width, corner radius of 0 mm and a maximum of 2.5 mm. |
Paul Horn R109.0815.1.7 TH35 Insert for chasing of metric internal thread (part profile) from bore diameter 7 mm to 10 mm in length with 1.5-1.75 mm pitch. |
Paul Horn R109.0815.3.7 TH35 Insert for chasing of metric internal thread (part profile) from bore diameter 7 mm to 20 mm in length with 1.5-1.75 mm pitch. |
Paul Horn R109.0815.5.7 TH35 Insert for chasing of metric internal thread (part profile) from bore diameter 7 mm to 30 mm in length with 1.5-1.75 mm pitch. |
Paul Horn R109.0915.3.6 TH35 Insert for chasing of metric internal trapezoidal thread (part profile) from bore diameter 6 mm to 20 mm length with 1.5 mm pitch. |
Paul Horn R109.1220.3.6 TH35 Insert for chasing of metric internal trapezoidal thread (part profile) from bore diameter 6 mm to 20 mm in length with 2 mm pitch. |
Paul Horn R109.1220.3.7 TH35 Insert for chasing of metric internal trapezoidal thread (part profile) from bore diameter 7 mm to 20 mm in length with 2 mm pitch. |
Paul Horn R109.1220.5.7 TH35 Insert for chasing of metric internal trapezoidal thread (part profile) from bore diameter 7 mm to 30 mm in length with 2 mm pitch. |
Paul Horn R109.1730.3.7 TH35 Insert for chasing of metric internal trapezoidal thread (part profile) from bore diameter 7 mm to 20 mm in length with 3 mm pitch. |
Paul Horn R109.1828.04.1.6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 10 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1828.04.1.HV6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 10 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1828.04.2.6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 15 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1828.04.2.HV6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 15 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1828.04.3.6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 20 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1828.04.3.HV6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 20 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1828.04.4.6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 25 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1828.04.4.HV6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 25 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1828.04.5.6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 30 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1828.04.5.HV6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 30 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1828.04.6.6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 35 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1828.04.6.HV6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 35 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1828.04.7.6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 40 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1828.04.7.HV6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 40 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1828.1.6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 10 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1828.1.HV6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 10 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1828.2.6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 15 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1828.2.HV6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 15 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1828.3.6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 20 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1828.3.HV6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 20 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1828.4.6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 25 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1828.4.HV6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 25 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1828.5.6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 30 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1828.5.HV6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 30 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1828.6.6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 35 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1828.6.HV6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 35 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1828.7.6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 40 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1828.7.HV6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 40 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1838.04.2.HV7 TH35 Insert for internal turning and copying from bore diameter 7 mm to 15 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1838.04.3.HV7 TH35 Insert for internal turning and copying from bore diameter 7 mm to 20 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1838.04.4.HV7 TH35 Insert for internal turning and copying from bore diameter 7 mm to 25 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1838.04.5.HV7 TH35 Insert for internal turning and copying from bore diameter 7 mm to 30 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1838.04.6.HV7 TH35 Insert for internal turning and copying from bore diameter 7 mm to 35 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1838.04.7.HV7 TH35 Insert for internal turning and copying from bore diameter 7 mm to 40 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1838.04.8.HV7 TH35 Insert for internal turning and copying from bore diameter 7 mm to 45 mm in length, with a corner radius of 0.4 mm. |
Paul Horn R109.1838.2.HV7 TH35 Insert for internal turning and copying from bore diameter 7 mm to 15 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1838.3.HV7 TH35 Insert for internal turning and copying from bore diameter 7 mm to 20 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1838.4.HV7 TH35 Insert for internal turning and copying from bore diameter 7 mm to 25 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1838.5.HV7 TH35 Insert for internal turning and copying from bore diameter 7 mm to 30 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1838.6.HV7 TH35 Insert for internal turning and copying from bore diameter 7 mm to 35 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1838.7.HV7 TH35 Insert for internal turning and copying from bore diameter 7 mm to 40 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.1838.8.HV7 TH35 Insert for internal turning and copying from bore diameter 7 mm to 45 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.3028.3.6 TH35 Insert rear turning and copying from bore diameter 6 mm to 20 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.3028.5.6 TH35 Insert rear turning and copying from bore diameter 6 mm to 30 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.3038.3.7 TH35 Insert rear turning and copying from bore diameter 7 mm to 20 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.3038.5.7 TH35 Insert rear turning and copying from bore diameter 7 mm to 30 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.4545.3.6 TH35 Insert for pocketing from bore diameter 6 mm to 20 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R109.4545.5.7 TH35 Insert for pocketing from bore diameter 7 mm to 30 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R10P.0100.1.00 TH35 Insert for the cutting of grooves from bore diameter 9 mm 1 mm width, corner radius of 0 mm and a maximum depth of 2 mm. |
Paul Horn R10P.0100.2.00 TH35 Insert deep for the cutting of grooves from bore diameter 10 mm 1 mm width, corner radius of 0 mm and a maximum of 3 mm. |
Paul Horn R10P.0150.1.00 TH35 Insert for the cutting of grooves from bore diameter 9 mm 1.5 mm width, corner radius of 0 mm and a maximum depth of 2 mm. |
Paul Horn R10P.0150.2.00 TH35 Insert deep for the cutting of grooves from bore diameter 10 mm 1.5 mm width, corner radius of 0 mm and a maximum of 3 mm. |
Paul Horn R10P.0200.1.02 TH35 Insert for the cutting of grooves from bore diameter 9 mm 2 mm width, corner radius 0.2 mm and a maximum depth of 2 mm. |
Paul Horn R10P.0200.2.02 TH35 Insert for the cutting of grooves from bore diameter 10 mm 2 mm width, corner radius 0.2 mm and a maximum depth of 3 mm. |
Paul Horn R10P.0250.1.02 TH35 Insert for the cutting of grooves from bore diameter 9 mm 2.5 mm width, corner radius 0.2 mm and a maximum depth of 2 mm. |
Paul Horn R10P.0300.1.02 TH35 Insert for the cutting of grooves from bore diameter 9 mm 3 mm width, corner radius 0.2 mm and a maximum depth of 2 mm. |
Paul Horn R110.0100.5.0 TN35 Insert deep for the cutting of grooves from bore diameter 10 mm to 30 mm in length with 1 mm width, corner radius of 0 mm and a maximum of 4 mm. |
Paul Horn R110.0100.5.8 TN35 Insert deep for the cutting of grooves from bore diameter 8 mm to 30 mm in length with 1 mm width, corner radius of 0 mm and a maximum of 2.8 mm. |
Paul Horn R110.0100.7.8 TN35 Insert deep for the cutting of grooves from bore diameter 8 mm to 40 mm in length with 1 mm width, corner radius of 0 mm and a maximum of 2.8 mm. |
Paul Horn R110.0100.9.0 TN35 Insert for the cutting of grooves from bore diameter 10 mm to 50 mm in length with 1 mm width, corner radius of 0 mm and a maximum depth of 4 mm. |
Paul Horn R110.0200.02.3.8 TN35 Insert deep for the cutting of grooves from bore diameter 8 mm to 20 mm in length with 2 mm width, corner radius 0.2 mm and a maximum of 2.8 mm. |
Paul Horn R110.0200.5.0 TN35 Insert deep for the cutting of grooves from bore diameter 10 mm to 30 mm in length with 2 mm width, corner radius of 0 mm and a maximum of 4 mm. |
Paul Horn R110.0200.5.8 TN35 Insert deep for the cutting of grooves from bore diameter 8 mm to 30 mm in length with 2 mm width, corner radius of 0 mm and a maximum of 2.8 mm. |
Paul Horn R110.0200.7.8 TN35 Insert deep for the cutting of grooves from bore diameter 8 mm to 40 mm in length with 2 mm width, corner radius of 0 mm and a maximum of 2.8 mm. |
Paul Horn R110.0200.9.0 TN35 Insert for the cutting of grooves from bore diameter 10 mm to 50 mm in length with 2 mm width, corner radius of 0 mm and a maximum depth of 4 mm. |
Paul Horn R110.0250.5.8 TN35 Insert deep for the cutting of grooves from bore diameter 8 mm to 30 mm in length with width 2.5 mm, corner radius of 0 mm and a maximum of 2.8 mm. |
Paul Horn R110.0250.7.8 TN35 Insert deep for the cutting of grooves from bore diameter 8 mm to 40 mm in length with width 2.5 mm, corner radius of 0 mm and a maximum of 2.8 mm. |
Paul Horn R110.0300.5.0 TN35 Insert deep for the cutting of grooves from bore diameter 10 mm to 30 mm in length with 3 mm width, corner radius of 0 mm and a maximum of 4 mm. |
Paul Horn R110.0300.9.0 TN35 Insert for the cutting of grooves from bore diameter 10 mm to 50 mm in length with 3 mm width, corner radius of 0 mm and a maximum depth of 4 mm. |
Paul Horn R110.1829.7.6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 40 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R110.1829.7.6 TI25 Insert for internal turning and copying from bore diameter 6 mm to 40 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R110.1829.9.6 TH35 Insert for internal turning and copying from bore diameter 6 mm to 50 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R110.1829.9.6 TI25 Insert for internal turning and copying from bore diameter 6 mm to 50 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R110.1829.9.8 TH35 Insert for internal turning and copying from bore diameter 8 mm to 50 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R110.1829.9.8 TI25 Insert for internal turning and copying from bore diameter 8 mm to 50 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R110.1829.9.H6 TI25 Insert for internal turning and copying from bore diameter 6 mm to 50 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R110.1829.9.H8 TI25 Insert for internal turning and copying from bore diameter 8 mm to 50 mm in length, with a corner radius of 0.2 mm. |
Paul Horn R110.LEHR.H.02 Plate for adjusting the cutting on spindle center. |
Paul Horn R111.0004.08 TH35 Insert deep for the cutting of grooves from bore diameter 11 mm with 0.8 mm width, full radius 0.4 mm and a maximum of 2.3 mm. |
Paul Horn R111.0004.08 TN35 Insert deep for the cutting of grooves from bore diameter 11 mm with 0.8 mm width, full radius 0.4 mm and a maximum of 2.3 mm. |
Paul Horn R111.0006.12 MG12 Insert for cutting of grooves from bore diameter 11 mm with 1.2 mm width, full radius 0.6 mm and a maximum of 2.3 mm deep. |
Paul Horn R111.0006.12 TH35 Insert deep for the cutting of grooves from bore diameter 11 mm with 1.2 mm width, full radius 0.6 mm and a maximum of 2.3 mm. |
Paul Horn R111.0006.12 TN35 Insert deep for the cutting of grooves from bore diameter 11 mm with 1.2 mm width, full radius 0.6 mm and a maximum of 2.3 mm. |
Paul Horn R111.0009.18 MG12 Insert deep for the cutting of grooves from bore diameter 11 mm with 1.8 mm width, full radius of 0.9 mm and a maximum of 2.3 mm. |
Paul Horn R111.0009.18 TH35 Insert deep for the cutting of grooves from bore diameter 11 mm with 1.8 mm width, full radius of 0.9 mm and a maximum of 2.3 mm. |
Paul Horn R111.0009.18 TN35 Insert deep for the cutting of grooves from bore diameter 11 mm with 1.8 mm width, full radius of 0.9 mm and a maximum of 2.3 mm. |
Paul Horn R111.0010.20 MG12 Insert deep for the cutting of grooves from bore diameter 11 mm with 2 mm width, full radius 1 mm and a maximum of 2.3 mm. |
Paul Horn R111.0010.20 TH35 Insert deep for the cutting of grooves from bore diameter 11 mm with 2 mm width, full radius 1 mm and a maximum of 2.3 mm. |
Paul Horn R111.0010.20 TN35 Insert deep for the cutting of grooves from bore diameter 11 mm with 2 mm width, full radius 1 mm and a maximum of 2.3 mm. |
Paul Horn R111.0015.30 MG12 Insert deep for the cutting of grooves from bore diameter 11 mm with 3 mm width, full radius of 1.5 mm and a maximum of 2.3 mm. |
Paul Horn R111.0015.30 TH35 Insert deep for the cutting of grooves from bore diameter 11 mm with 3 mm width, full radius of 1.5 mm and a maximum of 2.3 mm. |
Paul Horn R111.0015.30 TN35 Insert deep for the cutting of grooves from bore diameter 11 mm with 3 mm width, full radius of 1.5 mm and a maximum of 2.3 mm. |
Paul Horn R111.0070.00 TH35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 11 mm with 0.74 mm width (nominal width 0.7 mm) and a maximum of 1.2 mm deep. |
Paul Horn R111.0070.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 11 mm with 0.74 mm width (nominal width 0.7 mm) and a maximum of 1.2 mm deep. |
Paul Horn R111.0080.00 TH35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 11 mm with 0.84 mm width (nominal width 0.8 mm) and a maximum of 1.3 mm deep. |
Paul Horn R111.0080.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 11 mm with 0.84 mm width (nominal width 0.8 mm) and a maximum of 1.3 mm deep. |
Paul Horn R111.0090.00 MG12 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 11 mm with 0.94 mm width (nominal width 0.9 mm) and a maximum of 1.5 mm deep. |
Paul Horn R111.0090.00 TH35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 11 mm with 0.94 mm width (nominal width 0.9 mm) and a maximum of 1.5 mm deep. |
Paul Horn R111.0090.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 11 mm with 0.94 mm width (nominal width 0.9 mm) and a maximum of 1.5 mm deep. |
Paul Horn R111.0100.1.00 TN35 Insert for the cutting of grooves to from bore diameter 11 mm with 1.0 mm width (corner radius 0 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0110.00 MG12 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 11 mm with 1.19 mm width (nominal width 1.1 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0110.00 TH35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 11 mm with 1.19 width (nominal width 1.1 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0110.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 11 mm with 1.19 width (nominal width 1.1 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0130.00 MG12 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 11 mm 1.39 mm width (nominal width 1.3 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0130.00 TH35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 11 mm with 1.39 mm width (nominal width 1.3 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0130.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 11 mm 1.39 mm width (nominal width 1.3 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0150.00 MG12 Insert for cutting of grooves to from bore diameter 11 mm with 1.5 mm width (corner radius 0 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0150.00 TH35 Insert for the cutting of grooves to from bore diameter 11 mm with 1.5 mm width (corner radius 0 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0150.00 TN35 Insert for the cutting of grooves to from bore diameter 11 mm with 1.5 mm width (corner radius 0 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0160.00 MG12 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 11 mm with 1.69 mm width (nominal width 1.6 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0160.00 TH35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 11 mm with 1.69 mm width (nominal width 1.6 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0160.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 11 mm with 1.69 mm width (nominal width 1.6 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0200.00 MG12 Insert for cutting of grooves to from bore diameter 11 mm with 2 mm width (corner radius 0 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0200.00 TH35 Insert for the cutting of grooves to from bore diameter 11 mm with 2 mm width (corner radius 0 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0200.00 TN35 Insert for the cutting of grooves to from bore diameter 11 mm with 2 mm width (corner radius 0 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0200.02 MG12 Insert for cutting of grooves to from bore diameter 11 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0200.02 TH35 Insert deep for the cutting of grooves to from bore diameter 11 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 2.3 mm. |
Paul Horn R111.0200.02 TI25 Insert deep for the cutting of grooves to from bore diameter 11 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 2.3 mm. |
Paul Horn R111.0200.02 TN35 Insert deep for the cutting of grooves to from bore diameter 11 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 2.3 mm. |
Paul Horn R111.0205.01 TH35 Insert for chasing of metric internal thread (part profile) from bore diameter 11 mm with 0.5-0.75 mm pitch. |
Paul Horn R111.0205.01 TN35 Insert for chasing of metric internal thread (part profile) from bore diameter 11 mm with 0.5-0.75 mm pitch. |
Paul Horn R111.0250.00 MG12 Insert for cutting of grooves to from bore diameter 11 mm with width 2.5 mm (corner radius 0 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0250.00 TH35 Insert for the cutting of grooves to from bore diameter 11 mm with width 2.5 mm (corner radius 0 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0250.00 TN35 Insert for the cutting of grooves to from bore diameter 11 mm with width 2.5 mm (corner radius 0 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0300.00 MG12 Insert for cutting of grooves to from bore diameter 11 mm with 3 mm width (corner radius 0 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0300.00 TH35 Insert for the cutting of grooves to from bore diameter 11 mm with 3 mm width (corner radius 0 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0300.00 TN35 Insert for the cutting of grooves to from bore diameter 11 mm with 3 mm width (corner radius 0 mm) and a maximum of 2.3 mm deep. |
Paul Horn R111.0510.01 TH35 Insert for chasing of metric internal thread (part profile) from bore diameter 11 mm with 1-1.25 mm lead. |
Paul Horn R111.0510.01 TN35 Insert for chasing of metric internal thread (part profile) from bore diameter 11 mm with 1-1.25 mm lead. |
Paul Horn R111.0510.02 TN35 Insert for chasing of metric internal thread (solid profile) from bore diameter 11 mm with 1 mm pitch. |
Paul Horn R111.0557.03B CB10 Insert CBN equipped for hard internal turning from bore diameter 10 mm, corner radius 0.3 mm, design right, fits to clamp holder type B111. |
Paul Horn R111.0567.03.B CB10 Insert CBN equipped for hard internal turning from bore diameter 11 mm, corner radius 0.3 mm, design right, fits to clamp holder type B111. |
Paul Horn R111.0810.45 MG12 Insert deep to preparting from bore diameter 11 mm with 1 mm wide and a maximum of 1.5 mm. |
Paul Horn R111.0810.45 TI25 Insert deep to preparting from bore diameter 11 mm with 1 mm wide and a maximum of 1.5 mm. |
Paul Horn R111.0815.01 TH35 Insert for chasing of metric internal thread (part profile) from bore diameter 11 mm with 1.5-1.75 mm pitch. |
Paul Horn R111.0815.01 TN35 Insert for chasing of metric internal thread (part profile) from bore diameter 11 mm with 1.5-1.75 mm pitch. |
Paul Horn R111.0815.02 MG12 Insert for chasing of metric internal thread (solid profile) from bore diameter 11 mm with 1.5 mm pitch. |
Paul Horn R111.0815.02 TN35 Insert for chasing of metric internal thread (solid profile) from bore diameter 11 mm with 1.5 mm pitch. |
Paul Horn R111.1015.01 TN35 Insert for chasing of metric ISO internal trapezoidal thread to DIN 103 from bore diameter 11 mm with 1.5 mm pitch. |
Paul Horn R111.1020.01 TH35 Insert for chasing of metric internal thread (part profile) from bore diameter 11 mm with 2 mm pitch. |
Paul Horn R111.1020.01 TN35 Insert for chasing of metric internal thread (part profile) from bore diameter 11 mm with 2 mm pitch. |
Paul Horn R111.1020.02 TN35 Insert for chasing of metric internal thread (part profile) from bore diameter 11 mm with 2 mm pitch. |
Paul Horn R111.1220.01 TN35 Insert for chasing of metric ISO internal trapezoidal thread to DIN 103 from bore diameter 11 mm with 2 mm pitch. |
Paul Horn R111.1325.01 MG12 Insert for chasing of metric internal thread (part profile) from bore diameter 11 mm with 2.5 mm pitch. |
Paul Horn R111.1325.01 TH35 Insert for chasing of metric internal thread (part profile) from bore diameter 11 mm with 2.5 mm pitch. |
Paul Horn R111.1325.01 TN35 Insert for chasing of metric internal thread (solid profile) from bore diameter 11 mm with 2.5 mm pitch. |
Paul Horn R111.1325.02 TN35 Insert for chasing of metric internal thread (solid profile) from bore diameter 11 mm with 2.5 mm pitch. |
Paul Horn R111.1630.02 TN35 Insert for chasing of metric internal thread (solid profile) from bore diameter 11 mm with 3 mm pitch. |
Paul Horn R111.1730.01 MG12 Insert for chasing of metric ISO internal trapezoidal thread to DIN 103 from bore diameter 11 mm with 3 mm pitch. |
Paul Horn R111.1730.01 TN35 Insert for chasing of metric ISO internal trapezoidal thread to DIN 103 from bore diameter 11 mm with 3 mm pitch. |
Paul Horn R111.1855.02 MG12 Insert for internal turning and copying from bore diameter 9.8 mm with a corner radius of 0.2 mm. |
Paul Horn R111.1855.02 TH35 Insert for internal turning and copying from bore diameter 9.8 mm with a corner radius of 0.2 mm. |
Paul Horn R111.1855.02 TI25 Insert for internal turning and copying from bore diameter 9.8 mm with a corner radius of 0.2 mm. |
Paul Horn R111.1855.02 TN35 Insert for internal turning and copying from bore diameter 9.8 mm with a corner radius of 0.2 mm. |
Paul Horn R111.1867.02 MG12 Insert for internal turning and copying from bore diameter 11 mm with a corner radius of 0.2 mm. |
Paul Horn R111.1867.02 TH35 Insert for internal turning and copying from bore diameter 11 mm with a corner radius of 0.2 mm. |
Paul Horn R111.1867.02 TI25 Insert for internal turning and copying from bore diameter 11 mm with a corner radius of 0.2 mm. |
Paul Horn R111.1867.02 TN35 Insert for internal turning and copying from bore diameter 11 mm with a corner radius of 0.2 mm. |
Paul Horn R111.2240.01 TN35 Insert for chasing of metric ISO internal trapezoidal thread to DIN 103 from bore diameter 11 mm with 4 mm pitch. |
Paul Horn R111.3067.02 TH35 Insert rear turning and copying from bore diameter 11 mm with a corner radius of 0.2 mm. |
Paul Horn R111.3067.02 TN35 Insert rear turning and copying from bore diameter 11 mm with a corner radius of 0.2 mm. |
Paul Horn R111.3067.04 TH35 Insert rear turning and copying from bore diameter 11 mm with a corner radius of 0.4 mm. |
Paul Horn R111.4545.02 TN35 Insert for pocketing from bore diameter 11 mm with a corner radius of 0.2 mm. |
Paul Horn R111.4767.02 TH35 Insert for internal turning and copying from bore diameter 11 mm with a corner radius of 0.2 mm. |
Paul Horn R111.4767.02 TI25 Insert for internal turning and copying from bore diameter 11 mm with a corner radius of 0.2 mm. |
Paul Horn R111.4767.02 TN35 Insert for internal turning and copying from bore diameter 11 mm with a corner radius of 0.2 mm. |
Paul Horn R111.4767.04 TH35 Insert for internal turning and copying from bore diameter 11 mm with a corner radius of 0.4 mm. |
Paul Horn R111.5514.02 TN35 Insert to Strehlen of Whitworth pipe thread (solid profile) from bore diameter 11 mm with 14 transition / inch pitch. |
Paul Horn R111.5519.02 TA45 Insert to Strehlen of Whitworth pipe thread (solid profile) from bore diameter 11 mm with 19 transition / inch pitch. |
Paul Horn R111.5519.02 TN35 Insert to Strehlen of Whitworth pipe thread (solid profile) from bore diameter 11 mm with 19 transition / inch pitch. |
Paul Horn R114.0004.08 TI25 Insert TiCN coated |
Paul Horn R114.0006.12 TH35 Insert deep for the cutting of grooves from bore diameter 14 mm with 1.2 mm width, full radius 0.6 mm and a maximum of 4 mm. |
Paul Horn R114.0006.12 TN35 Insert deep for the cutting of grooves from bore diameter 14 mm with 1.2 mm width, full radius 0.6 mm and a maximum of 4 mm. |
Paul Horn R114.0009.18 TH35 Insert deep for the cutting of grooves from bore diameter 14 mm with 1.8 mm width, full radius of 0.9 mm and a maximum of 4 mm. |
Paul Horn R114.0009.18 TN35 Insert deep for the cutting of grooves from bore diameter 14 mm with 1.8 mm width, full radius of 0.9 mm and a maximum of 4 mm. |
Paul Horn R114.0010.20 TH35 Insert deep for the cutting of grooves from bore diameter 14 mm with 2 mm width, full radius 1 mm and a maximum of 4 mm. |
Paul Horn R114.0010.20 TN35 Insert deep for the cutting of grooves from bore diameter 14 mm with 2 mm width, full radius 1 mm and a maximum of 4 mm. |
Paul Horn R114.0011.22 TH35 Insert deep for the cutting of grooves from bore diameter 14 mm with 2.2 mm width, full radius 1.1 mm and a maximum of 4 mm. |
Paul Horn R114.0011.22 TN35 Insert deep for the cutting of grooves from bore diameter 14 mm with 2.2 mm width, full radius 1.1 mm and a maximum of 4 mm. |
Paul Horn R114.0015.30 TH35 Insert deep for the cutting of grooves from bore diameter 14 mm with 3 mm width, full radius of 1.5 mm and a maximum of 4 mm. |
Paul Horn R114.0015.30 TN35 Insert deep for the cutting of grooves from bore diameter 14 mm with 3 mm width, full radius of 1.5 mm and a maximum of 4 mm. |
Paul Horn R114.0020.40 TH35 Insert deep for the cutting of grooves from bore diameter 14 mm with 4 mm width, full radius 2 mm and a maximum of 4 mm. |
Paul Horn R114.0070.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 14 mm with 0.74 mm width (nominal width 0.7 mm) and a maximum of 1.2 mm deep. |
Paul Horn R114.0080.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 14 mm with 0.84 mm width (nominal width 0.8 mm) and a maximum of 1.3 mm deep. |
Paul Horn R114.0090.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 14 mm with 0.94 mm width (nominal width 0.9 mm) and a maximum of 1.5 mm deep. |
Paul Horn R114.0110.00 TH35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 14 mm with 1.19 width (nominal width 1.1 mm) and a maximum of 4 mm deep. |
Paul Horn R114.0110.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 14 mm with 1.19 width (nominal width 1.1 mm) and a maximum of 4 mm deep. |
Paul Horn R114.0130.00 TH35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 14 mm 1.39 mm width (nominal width 1.3 mm) and a maximum of 4 mm deep. |
Paul Horn R114.0130.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 14 mm 1.39 mm width (nominal width 1.3 mm) and a maximum of 4 mm deep. |
Paul Horn R114.0150.00 MG12 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 1.5 mm width (corner radius 0 mm) and a maximum of 4 mm deep. |
Paul Horn R114.0150.00 TH35 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 1.5 mm width (corner radius 0 mm) and a maximum of 4 mm deep. |
Paul Horn R114.0150.00 TN35 Insert to Inneneinstechen of grooves from bore diameter 14 mm with 1.5 mm width (corner radius 0 mm) and a maximum of 4 mm deep. |
Paul Horn R114.0150.1.02 TH35 Insert for Inneneinstechen of grooves from bore diameter 16.5 mm with 1.5 mm width (nose radius 0.2 mm) and a maximum of 6.5 mm deep. |
Paul Horn R114.0150.1.02 TN35 Insert to Inneneinstechen of grooves from bore diameter 16.5 mm with 1.5 mm width (nose radius 0.2 mm) and a maximum of 6.5 mm deep. |
Paul Horn R114.0160.00 TH35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 14 mm with 1.69 mm width (nominal width 1.6 mm) and a maximum of 4 mm deep. |
Paul Horn R114.0160.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 14 mm with 1.69 mm width (nominal width 1.6 mm) and a maximum of 4 mm deep. |
Paul Horn R114.0200.00 MG12 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 2 mm width (corner radius 0 mm) and a maximum of 4 mm deep. |
Paul Horn R114.0200.00 TH35 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 2 mm width (corner radius 0 mm) and a maximum of 4 mm deep. |
Paul Horn R114.0200.00 TN35 Insert to Inneneinstechen of grooves from bore diameter 14 mm with 2 mm width (corner radius 0 mm) and a maximum of 4 mm deep. |
Paul Horn R114.0200.02 MG12 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |