|
Paul Horn DSKM.2.30.63.06.L31 TS3H Cutter shank as micro cutters for soft and hard milling with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSKM.2.30.63.06.L31 TS3K Cutter shank as micro cutters for soft and hard milling with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSKM.2.300.030 TS3K Micro cutters full radius DSKM.2.300.030, 2 blades, 30 В° helix angle, center cutting |
|
Paul Horn DSKM.2.300.050 TS3K Micro cutters full radius DSKM.2.300.050, 2 blades, 30 В° helix angle, center cutting |
|
Paul Horn DSKM.2.300.070 TS3K Micro cutters full radius DSKM.2.300.070, 2 blades, 30 В° helix angle, center cutting |
|
Paul Horn DSKMA.010.030 MG3K Ball cutter as micro mills for aluminum machining with radius 0.05mm, 2 blades with a diameter of 0.1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.010.050 MG3K Ball cutter as micro mills for aluminum machining with radius 0.05mm, 2 blades with a diameter of 0.1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.010.070 MG3K Ball cutter as micro mills for aluminum machining with radius 0.05mm, 2 blades with a diameter of 0.1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.020.030 MG3K Ball cutter as micro mills for aluminum machining with radius 0.1 mm, 2 cutting edges with a diameter of 0.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.020.050 MG3K Ball cutter as micro mills for aluminum machining with radius 0.1 mm, 2 cutting edges with a diameter of 0.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.020.070 MG3K Ball cutter as micro mills for aluminum machining with radius 0.1 mm, 2 cutting edges with a diameter of 0.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.030.030 MG3K Ball cutter as micro mills for aluminum machining with radius 0.15mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.030.050 MG3K Ball cutter as micro mills for aluminum machining with radius 0.15mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.030.070 MG3K Ball cutter as micro mills for aluminum machining with radius 0.15mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.050.030 MG3K Ball cutter as micro mills for aluminum machining with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.050.050 MG3K Ball cutter as micro mills for aluminum machining with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.050.070 MG3K Ball cutter as micro mills for aluminum machining with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.060.030 MG3K Ball cutter as micro mills for aluminum machining with radius 0.3 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.060.050 MG3K Ball cutter as micro mills for aluminum machining with radius 0.3 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.060.070 MG3K Ball cutter as micro mills for aluminum machining with radius 0.3 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.080.030 MG3K Ball cutter as micro mills for aluminum machining with radius 0.4 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.080.050 MG3K Ball cutter as micro mills for aluminum machining with radius 0.4 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.080.070 MG3K Ball cutter as micro mills for aluminum machining with radius 0.4 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.100.030 MG3K Ball cutter as micro mills for aluminum machining with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.100.050 MG3K Ball cutter as micro mills for aluminum machining with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.100.070 MG3K Ball cutter as micro mills for aluminum machining with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.120.030 MG3K Ball cutter as micro mills for aluminum machining with radius 0.6 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.120.050 MG3K Ball cutter as micro mills for aluminum machining with radius 0.6 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.120.070 MG3K Ball cutter as micro mills for aluminum machining with radius 0.6 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.150.030 MG3K Ball cutter as micro mills for aluminum machining with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.150.050 MG3K Ball cutter as micro mills for aluminum machining with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.150.070 MG3K Ball cutter as micro mills for aluminum machining with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.200.030 MG3K Ball cutter as micro mills for aluminum machining with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.200.050 MG3K Ball cutter as micro mills for aluminum machining with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.200.070 MG3K Ball cutter as micro mills for aluminum machining with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.250.030 MG3K Ball cutter as micro mills for aluminum machining with radius 1.25mm, 2 blades with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.250.050 MG3K Ball cutter as micro mills for aluminum machining with radius 1.25mm, 2 blades with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.250.070 MG3K Ball cutter as micro mills for aluminum machining with radius 1.25mm, 2 blades with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.300.030 MG3K Ball cutter as micro mills for aluminum machining with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.300.050 MG3K Ball cutter as micro mills for aluminum machining with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMA.300.070 MG3K Ball cutter as micro mills for aluminum machining with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMG.2.03.50.4.L40 CD5K Cutter shank as micro cutters for working graphite with radius 0.15mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMG.2.04.50.4.L50 CD5K Cutter shank as micro cutters for working graphite with radius 0.2 mm, 2 cutting edges with a diameter of 0.4 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMG.2.05.50.4.L60 CD5K Cutter shank as micro cutters for working graphite with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMG.2.05.63.6.L40 CD5K Cutter shank as micro cutters for working graphite with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSKMG.2.05.63.6.L60 CD5K Cutter shank as micro cutters for working graphite with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSKMG.2.06.50.4.L70 CD5K Cutter shank as micro cutters for working graphite with radius 0.3 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMG.2.08.50.4.L80 CD5K Cutter shank as micro cutters for working graphite with radius 0.4 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMG.2.10.50.4.L10 CD5K Cutter shank as micro cutters for working graphite with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMG.2.10.50.4.L60 CD5K Cutter shank as micro cutters for working graphite with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMG.2.10.63.6.L10 CD5K Cutter shank as micro cutters for working graphite with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSKMG.2.15.50.4.L10 CD5K Cutter shank as micro cutters for working graphite with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMG.2.15.63.6.L10 CD5K Cutter shank as micro cutters for working graphite with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSKMH.020.015 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.1 mm, 2 cutting edges with a diameter of 0.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.020.030 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.1 mm, 2 cutting edges with a diameter of 0.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.020.050 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.1 mm, 2 cutting edges with a diameter of 0.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.030.015 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.15mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.030.030 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.15mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.030.050 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.15mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.040.015 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.2 mm, 2 cutting edges with a diameter of 0.4 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.040.030 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.2 mm, 2 cutting edges with a diameter of 0.4 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.040.050 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.2 mm, 2 cutting edges with a diameter of 0.4 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.050.015 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.050.030 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.050.050 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.050.070 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.060.015 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.3 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.060.030 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.3 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.060.050 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.3 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.060.070 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.3 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.080.015 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.4 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.080.030 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.4 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.080.050 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.4 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.080.070 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.4 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.100.015 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.100.030 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.100.050 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.100.070 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.120.015 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.6 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.120.030 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.6 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.120.050 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.6 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.120.070 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.6 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.150.015 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.150.030 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.150.050 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.150.070 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.200.015 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.200.030 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.200.050 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.200.070 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.250.015 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 1.25mm, 2 blades with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.250.030 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 1.25mm, 2 blades with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.250.050 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 1.25mm, 2 blades with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.250.070 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 1.25mm, 2 blades with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.300.015 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.300.030 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.300.050 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMH.300.070 TS3E End mills as micro cutters for hard machining 50-70 HRC with radius 1.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMK.2.03.50.4.L30 CN2K Cutter shank as micro cutters for machining copper with radius 0.15mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMK.2.04.50.4.L30 CN2K Cutter shank as micro cutters for machining copper with radius 0.2 mm, 2 cutting edges with a diameter of 0.4 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMK.2.05.50.4.L30 CN2K Cutter shank as micro cutters for machining copper with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMK.2.05.50.4.L50 CN2K Cutter shank as micro cutters for machining copper with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMK.2.05.63.6.L30 CN2K Cutter shank as micro cutters for machining copper with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSKMK.2.05.63.6.L50 CN2K Cutter shank as micro cutters for machining copper with radius of 0.25 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSKMK.2.06.50.4.L50 CN2K Cutter shank as micro cutters for machining copper with radius 0.3 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMK.2.08.50.4.L60 CN2K Cutter shank as micro cutters for machining copper with radius 0.4 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMK.2.10.50.4.L40 CN2K Cutter shank as micro cutters for machining copper with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMK.2.10.50.4.L80 CN2K Cutter shank as micro cutters for machining copper with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMK.2.10.63.6.L40 CN2K Cutter shank as micro cutters for machining copper with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSKMK.2.10.63.6.L80 CN2K Cutter shank as micro cutters for machining copper with radius 0.5 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSKMK.2.15.50.4.L10 CN2K Cutter shank as micro cutters for machining copper with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMK.2.15.63.6.L10 CN2K Cutter shank as micro cutters for machining copper with radius 0.75 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSKMK.2.20.50.4.L12 CN2K Cutter shank as micro cutters for machining copper with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSKMK.2.20.63.6.L12 CN2K Cutter shank as micro cutters for machining copper with radius 1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSM.10.10.77.10 TS3K End mills for soft and hard milling with a 45 В° helix angle, 10-fluted with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSM.12.12.88.12 TS3K End mills for soft and hard milling with a 45 В° helix angle, 12-fluted with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSM.16.16.88.16 TS3K End mills for soft and hard milling with a 45 В° helix angle, 16-fluted with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSM.6.03.63.06 TS3K End mills for soft and hard milling with a 45 В° helix angle, 6-edged with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSM.6.03.63.06S TS3K End mills for soft and hard milling with a 45 В° helix angle, 6-edged with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSM.6.04.63.06 TS3K End mills for soft and hard milling with a 45 В° helix angle, 6-edged with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSM.6.04.63.06S TS3K End mills for soft and hard milling with a 45 В° helix angle, 6-edged with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSM.6.05.63.06 TS3K End mills for soft and hard milling with a 45 В° helix angle, 6-edged with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSM.6.06.63.06 TS3K End mills for soft and hard milling with a 45 В° helix angle, 6-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSM.6.06.63.06S TS3K End mills for soft and hard milling with a 45 В° helix angle, 6-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSM.6.08.63.08 TS3K End mills for soft and hard milling with a 45 В° helix angle, 6-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSM.6.08.63.08S TS3K End mills for soft and hard milling with a 45 В° helix angle, 6-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSM.6.10.69.10 TS3K End mills for soft and hard milling with a 45 В° helix angle, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSM.6.10.69.10S TS3K End mills for soft and hard milling with a 45 В° helix angle, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSM.6.12.77.12 TS3K End mills for soft and hard milling with a 45 В° helix angle, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSM.6.12.77.12S TS3K End mills for soft and hard milling with a 45 В° helix angle, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSM.6.16.88.16 TS3K End mills for soft and hard milling with a 45 В° helix angle, 6-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSM.6.16.88.16S TS3K End mills for soft and hard milling with a 45 В° helix angle, 6-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSM.8.08.77.08 TS3K End mills for soft and hard milling with a 45 В° helix angle, 8-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMA.010.030 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, zenrumschneidend, 2 blades with a diameter of 0.1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.010.050 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 0.1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.010.070 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 0.1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.020.030 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 0.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.020.050 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 0.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.020.070 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 0.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.030.030 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 0.3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.030.050 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 0.3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.030.070 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 0.3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.050.030 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.050.050 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.050.070 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.060.030 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.060.050 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.060.070 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.080.030 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.080.050 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.080.070 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.100.030 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.100.050 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.100.070 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.120.030 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 1.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.120.050 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 1.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.120.070 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 1.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.150.030 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.150.050 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.150.070 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.200.030 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.200.050 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.200.070 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.250.030 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.250.050 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.250.070 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.300.030 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.300.050 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMA.300.070 MG3K End mills as Mikrofäser for machining aluminum with a 30 ° helix angle, center cutting, 2 flutes with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMH.6.03.040 TS3E End mills for hard milling 50-70 HRC, 6-edged with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMH.6.03.55.06 TS3E End mills for hard milling 50-70 HRC, 6-edged with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMH.6.04.040 TS3E End mills for hard milling 50-70 HRC, 6-edged with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMH.6.04.55.06 TS3E End mills for hard milling 50-70 HRC, 6-edged with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMH.6.05.040 TS3E End mills for hard milling 50-70 HRC, 6-edged with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMH.6.05.55.06 TS3E End mills for hard milling 50-70 HRC, 6-edged with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMH.6.06.040 TS3E End mills for hard milling 50-70 HRC, 6-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMH.6.06.63.06 TS3E End mills for hard milling 50-70 HRC, 6-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMH.6.08.040 TS3E End mills for hard milling 50-70 HRC, 6-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMH.6.08.63.08 TS3E End mills for hard milling 50-70 HRC, 6-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMH.6.10.040 TS3E End mills for hard milling 50-70 HRC, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMH.6.12.040 TS3E End mills for hard milling 50-70 HRC, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMH.6.12.88.12 TS3E End mills for hard milling 50-70 HRC, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMH.6.16.040 TS3E End mills for hard milling 50-70 HRC, 6-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSMH.6.16.99.16 TS3E End mills for hard milling 50-70 HRC, 6-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSMK.3.03.50.04 CN2K End mills for processing of copper, 3 flutes with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMK.3.03.63.06 CN2K End mills for processing of copper, 3 flutes with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMK.3.05.63.06 CN2K End mills for processing of copper, 3 flutes with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMK.3.06.63.06 CN2K End mills for processing of copper, 3 flutes with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMK.3.08.77.08 CN2K End mills for processing of copper, 3 flutes with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMK.3.10.77.10 CN2K End mills for processing of copper, 3 flutes with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMK.3.12.88.12 CN2K End mills for processing of copper, 3 flutes with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMK.3.16.99.16 CN2K End mills for processing of copper, 3 flutes with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSML.6.08.077.08 TS3K End mills for soft and hard milling, 45 В° helix angle, corner radius 0.5 mm, 6-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSML.6.10.088.10 TS3K End mills for soft and hard milling, 45 В° helix angle, corner radius 0.5 mm, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSML.6.12.099.12 TS3K End mills for soft and hard milling, 45 В° helix angle, corner radius 0.5 mm, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSML.6.16.101.16 TS3K End mills for soft and hard milling, 45 В° helix angle, corner radius 0.5 mm, 8-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSMMG.2.03.50.4.L40 CD5K End mills as micro cutters for machining graphite with corner radius 0.05mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMG.2.04.50.4.L50 CD5K End mills as micro cutters for machining graphite with corner radius 0.05mm, 2 blades with a diameter of 0.4 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMG.2.05.50.4.L40 CD5K End mills as micro cutters for machining graphite with corner radius 0.05mm, 2 blades with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMG.2.05.50.4.L60 CD5K End mills as micro cutters for machining graphite with corner radius 0.05mm, 2 blades with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMG.2.05.63.6.L40 CD5K End mills as micro cutters for machining graphite with corner radius 0.05mm, 2 blades with a diameter of 0.5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMMG.2.05.63.6.L60 CD5K End mills as micro cutters for machining graphite with corner radius 0.05mm, 2 blades with a diameter of 0.5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMMG.2.06.50.4.L70 CD5K End mills as micro cutters for machining graphite with corner radius 0.05mm, 2 blades with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMG.2.08.50.4.L80 CD5K End mills as micro cutters for machining graphite with corner radius 0.05mm, 2 blades with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMG.2.10.50.4.L10 CD5K End mills as micro cutters for machining graphite with corner radius 0.05mm, 2 blades with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMG.2.10.50.4.L60 CD5K End mills as micro cutters for machining graphite with corner radius 0.05mm, 2 blades with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMG.2.10.63.6.L10 CD5K Micro cutter More Schneider diamond- coated |
|
Paul Horn DSMMG.2.10.63.6.L60 CD5K End mills as micro cutters for machining graphite with corner radius 0.05mm, 2 blades with a diameter of 1 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMMG.2.15.50.4.L10 CD5K End mills as micro cutters for machining graphite with corner radius 0.05mm, 2 blades with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMG.2.15.63.6.L10 CD5K End mills as micro cutters for machining graphite with corner radius 0.05mm, 2 blades with a diameter of 1.5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMMK.2.03.50.4.L30 CN2K End mills as micro cutters for machining copper with corner radius 0.05mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMK.2.04.50.4.L30 CN2K End mills as micro cutters for machining copper with corner radius 0.05mm, 2 blades with a diameter of 0.4 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMK.2.05.50.4.L30 CN2K End mills as micro cutters for machining copper with corner radius 0.05mm, 2 blades with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMK.2.05.50.4.L50 CN2K End mills as micro cutters for machining copper with corner radius 0.05mm, 2 blades with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMK.2.05.63.6.L30 CN2K End mills as micro cutters for machining copper with corner radius 0.05mm, 2 blades with a diameter of 0.5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMMK.2.05.63.6.L50 CN2K End mills as micro cutters for machining copper with corner radius 0.05mm, 2 blades with a diameter of 0.5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMMK.2.06.50.4.L50 CN2K End mills as micro cutters for machining copper with corner radius 0.05mm, 2 blades with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMK.2.08.50.4.L60 CN2K End mills as micro cutters for machining copper with corner radius 0.05mm, 2 blades with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMK.2.10.50.4.L40 CN2K End mills as micro cutters for machining copper with corner radius 0.05mm, 2 blades with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMK.2.10.50.4.L80 CN2K End mills as micro cutters for machining copper with corner radius 0.05mm, 2 blades with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMK.2.10.63.6.L40 CN2K End mills as micro cutters for machining copper with corner radius 0.05mm, 2 blades with a diameter of 1 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMMK.2.10.63.6.L80 CN2K End mills as micro cutters for machining copper with corner radius 0.05mm, 2 blades with a diameter of 1 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMMK.2.15.50.4.L10 CN2K End mills as micro cutters for machining copper with corner radius 0.05mm, 2 blades with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMK.2.15.63.6.L10 CN2K End mills as micro cutters for machining copper with corner radius 0.05mm, 2 blades with a diameter of 1.5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMMK.2.20.50.4.L12 CN2K End mills as micro cutters for machining copper with corner radius 0.05mm, 2 blades with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMMK.2.20.63.6.L12 CN2K End mills as micro cutters for machining copper with corner radius 0.05mm, 2 blades with a diameter of 2 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.10.10.77.10.05 TS3H End mills for soft and hard milling with corner radius 0.5 mm, 10 flutes with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMR.10.10.77.10.05 TS3K End mills for soft and hard milling with corner radius 0.5 mm, 10 flutes with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMR.12.12.88.12.05 TS3H End mills for soft and hard milling with corner radius 0.5 mm, 12 flutes with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMR.12.12.88.12.05 TS3K End mills for soft and hard milling with corner radius 0.5 mm, 12 flutes with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMR.16.16.88.16.05 TS3K End mills for soft and hard milling with corner radius 0.5 mm, 16 flutes with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSMR.6.03.63.06.03 TS3H End mills for soft and hard milling with corner radius 0.3 mm, 6-edged with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.03.63.06.03 TS3K End mills for soft and hard milling with corner radius 0.3 mm, 6-edged with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.03.63.06.03S TS3H End mills for soft and hard milling with corner radius 0.3 mm, 6-edged with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.03.63.06.03S TS3K End mills for soft and hard milling with corner radius 0.3 mm, 6-edged with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.04.63.06.03 TS3H End mills for soft and hard milling with corner radius 0.3 mm, 6-edged with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.04.63.06.03 TS3K End mills for soft and hard milling with corner radius 0.3 mm, 6-edged with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.04.63.06.03S TS3H End mills for soft and hard milling with corner radius 0.3 mm, 6-edged with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.04.63.06.03S TS3K End mills for soft and hard milling with corner radius 0.3 mm, 6-edged with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.05.63.06.03 TS3H End mills for soft and hard milling with corner radius 0.3 mm, 6-edged with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.05.63.06.03 TS3K End mills for soft and hard milling with corner radius 0.3 mm, 6-edged with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.05.63.06.03S TS3H End mills for soft and hard milling with corner radius 0.3 mm, 6-edged with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.05.63.06.03S TS3K End mills for soft and hard milling with corner radius 0.3 mm, 6-edged with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.05.63.06.05 TS3H End mills More Schneider TiAlN coated |
|
Paul Horn DSMR.6.05.63.06.05 TS3K End mills for soft and hard milling with corner radius 0.5 mm, 6-edged with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.05.63.06.05S TS3H End mills for soft and hard milling with corner radius 0.5 mm, 6-edged with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.05.63.06.05S TS3K End mills for soft and hard milling with corner radius 0.5 mm, 6-edged with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.06.63.06.05 TS3H End mills for soft and hard milling with corner radius 0.5 mm, 6-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.06.63.06.05 TS3K End mills for soft and hard milling with corner radius 0.5 mm, 6-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.06.63.06.05S TS3K End mills for soft and hard milling with corner radius 0.5 mm, 6-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.06.63.06.10 TS3H End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.06.63.06.10 TS3K End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.06.63.06.10S TS3H End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.06.63.06.10S TS3K End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMR.6.08.63.08.05 TS3H End mills for soft and hard milling with corner radius 0.5 mm, 6-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMR.6.08.63.08.05S TS3H End mills for soft and hard milling with corner radius 0.5 mm, 6-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMR.6.08.63.08.05S TS3K End mills More Schneider TiAlN coated |
|
Paul Horn DSMR.6.08.63.08.10 TS3H End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMR.6.08.63.08.10 TS3K End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMR.6.08.63.08.10S TS3H End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMR.6.08.63.08.10S TS3K End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMR.6.10.69.10.05 TS3H End mills for soft and hard milling with corner radius 0.5 mm, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMR.6.10.69.10.05 TS3K End mills for soft and hard milling with corner radius 0.5 mm, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMR.6.10.69.10.05S TS3H End mills for soft and hard milling with corner radius 0.5 mm, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMR.6.10.69.10.05S TS3K End mills for soft and hard milling with corner radius 0.5 mm, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMR.6.10.69.10.10 TS3H End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMR.6.10.69.10.10 TS3K End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMR.6.10.69.10.10S TS3H End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMR.6.10.69.10.10S TS3K End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMR.6.10.69.10.15 TS3H End mills More Schneider TiAlN coated |
|
Paul Horn DSMR.6.10.69.10.15 TS3K End mills for soft and hard milling with corner radius 1.5 mm, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMR.6.10.69.10.15S TS3K End mills for soft and hard milling with corner radius 1.5 mm, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMR.6.12.77.12.05 TS3H End mills for soft and hard milling with corner radius 0.5 mm, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMR.6.12.77.12.05 TS3K End mills for soft and hard milling with corner radius 0.5 mm, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMR.6.12.77.12.05S TS3K End mills for soft and hard milling with corner radius 0.5 mm, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMR.6.12.77.12.10 TS3H End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMR.6.12.77.12.10 TS3K End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMR.6.12.77.12.10S TS3H End mills More Schneider TiAlN coated |
|
Paul Horn DSMR.6.12.77.12.10S TS3K End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMR.6.12.77.12.20 TS3H End mills for soft and hard milling with corner radius 2 mm, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMR.6.12.77.12.20 TS3K End mills for soft and hard milling with corner radius 2 mm, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMR.6.12.77.12.20S TS3H End mills for soft and hard milling with corner radius 2 mm, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMR.6.12.77.12.20S TS3K End mills for soft and hard milling with corner radius 2 mm, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMR.6.16.88.16.05 TS3H End mills for soft and hard milling with corner radius 0.5 mm, 6-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSMR.6.16.88.16.10 TS3H End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSMR.6.16.88.16.10 TS3K End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSMR.6.16.88.16.10S TS3H End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSMR.6.16.88.16.10S TS3K End mills for soft and hard milling with corner radius 1 mm, 6-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSMR.6.16.88.16.20 TS3H End mills for soft and hard milling with corner radius 2 mm, 6-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSMR.6.16.88.16.20 TS3K End mills for soft and hard milling with corner radius 2 mm, 6-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSMR.6.16.88.16.20S TS3H End mills for soft and hard milling with corner radius 2 mm, 6-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSMR.6.16.88.16.20S TS3K End mills for soft and hard milling with corner radius 2 mm, 6-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSMR.8.08.77.08.05 TS3H End mills for soft and hard milling with corner radius 0.5 mm, 8-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMR.8.08.77.08.05 TS3K End mills More Schneider TiAlN coated |
|
Paul Horn DSMRC.4.03.55.06.02 TSCC End mills for processing cobalt-chromium alloys with corner radius 0.2 mm, 4-edged, with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRC.4.03.55.06.3S TSCC End mills for processing cobalt-chromium alloys with corner radius 0.3 mm, 4-edged, with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRC.4.04.55.06.02 TSCC End mills for processing cobalt-chromium alloys with corner radius 0.2 mm, 4-edged, with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRC.4.04.55.06.3S TSCC End mills for processing cobalt-chromium alloys with corner radius 0.3 mm, 4-edged, with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRC.4.05.55.06.02 TSCC End mills for processing cobalt-chromium alloys with corner radius 0.2 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRC.4.05.55.06.5S TSCC End mills for processing cobalt-chromium alloys with corner radius 0.5 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRC.5.06.63.06.02 TSCC End mills for processing cobalt-chromium alloys with corner radius 0.2 mm, 5-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRC.5.06.63.06.5S TSCC End mills for processing cobalt-chromium alloys with corner radius 0.5 mm, 5-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRC.5.08.63.08.10 TSCC End mills for processing cobalt-chromium alloys with corner radius 1 mm, 5 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMRC.5.08.63.08.5S TSCC End mills for processing cobalt-chromium alloys with corner radius 0.5 mm, 5-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMRC.5.10.77.10.10 TSCC End mills for processing cobalt-chromium alloys with corner radius 1 mm, 5 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMRC.5.10.77.10.5S TSCC End mills for processing cobalt-chromium alloys with corner radius 0.5 mm, 5-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMRC.7.12.88.12.10 TSCC End mills for processing cobalt-chromium alloys with corner radius 1 mm, 7-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMRC.7.12.88.12.2S TSCC End mills for processing cobalt-chromium alloys with corner radius 0.2 mm, 7-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMRC.7.16.99.16.05 TSCC End mills for processing cobalt-chromium alloys with corner radius 0.5 mm, 7-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSMRC.7.16.99.16.20 TSCC End mills for processing cobalt-chromium alloys with corner radius 2 mm, 7-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSMRH.6.03.020.040 TS3E End mills for hard milling 50-70 HRC with corner radius 0.2 mm, 6-edged with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.03.050.040 TS3E End mills for hard milling 50-70 HRC with corner radius 0.5 mm, 6-edged with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.03.100.040 TS3E End mills for hard milling 50-70 HRC with corner radius 1 mm, 6-edged with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.03.55.06.01TS3E End mills for hard milling 50-70 HRC with corner radius 0.1 mm, 6-edged with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.03.55.06.1S TS3E End mills for hard milling 50-70 HRC with corner radius 0.1 mm, 6-edged with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.04.020.040 TS3E End mills for hard milling 50-70 HRC with corner radius 0.2 mm, 6-edged with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.04.050.040 TS3E End mills for hard milling 50-70 HRC with corner radius 0.5 mm, 6-edged with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.04.100.040 TS3E End mills for hard milling 50-70 HRC with corner radius 1 mm, 6-edged with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.04.55.06.02 TS3E End mills for hard milling 50-70 HRC with corner radius 0.2 mm, 6-edged with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.04.55.06.3S TS3E End mills for hard milling 50-70 HRC with corner radius 0.3 mm, 6-edged with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.05.020.040 TS3E End mills for hard milling 50-70 HRC with corner radius 0.2 mm, 6-edged with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.05.050.040 TS3E End mills for hard milling 50-70 HRC with corner radius 0.5 mm, 6-edged with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.05.100.040 TS3E End mills for hard milling 50-70 HRC with corner radius 1 mm, 6-edged with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.05.55.06.2S TS3E End mills for hard milling 50-70 HRC with corner radius 0.2 mm, 6-edged with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.06.020.040 TS3E End mills for hard milling 50-70 HRC with corner radius 0.2 mm, 6-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.06.050.040 TS3E End mills for hard milling 50-70 HRC with corner radius 0.5 mm, 6-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.06.100.040 TS3E End mills for hard milling 50-70 HRC with corner radius 1 mm, 6-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.06.63.06.03 TS3E End mills for hard milling 50-70 HRC with corner radius 0.3 mm, 6-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.06.63.06.3S TS3E End mills for hard milling 50-70 HRC with corner radius 0.3 mm, 6-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRH.6.08.020.040 TS3E End mills for hard milling 50-70 HRC with corner radius 0.2 mm, 6-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMRH.6.08.050.040 TS3E End mills for hard milling 50-70 HRC with corner radius 0.5 mm, 6-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMRH.6.08.100.040 TS3E End mills for hard milling 50-70 HRC with corner radius 1 mm, 6-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMRH.6.08.63.08.5S TS3E End mills for hard milling 50-70 HRC with corner radius 0.5 mm, 6-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMRH.6.10.020.040 TS3E End mills for hard milling 50-70 HRC with corner radius 0.2 mm, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMRH.6.10.050.040 TS3E End mills for hard milling 50-70 HRC with corner radius 0.5 mm, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMRH.6.10.100.040 TS3E End mills for hard milling 50-70 HRC with corner radius 1 mm, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMRH.6.10.200.040 TS3E End mills for hard milling 50-70 HRC with corner radius 2 mm, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMRH.6.10.77.10.05 TS3E End mills for hard milling 50-70 HRC with corner radius 0.5 mm, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMRH.6.10.77.10.5S TS3E End mills for hard milling 50-70 HRC with corner radius 0.5 mm, 6-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMRH.6.12.020.040 TS3E End mills for hard milling 50-70 HRC with corner radius 0.2 mm, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMRH.6.12.050.040 TS3E End mills for hard milling 50-70 HRC with corner radius 0.5 mm, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMRH.6.12.100.040 TS3E End mills for hard milling 50-70 HRC with corner radius 1 mm, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMRH.6.12.200.040 TS3E End mills for hard milling 50-70 HRC with corner radius 2 mm, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMRH.6.12.88.12.05 TS3E End mills for hard milling 50-70 HRC with corner radius 0.5 mm, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMRH.6.12.88.12.5S TS3E End mills for hard milling 50-70 HRC with corner radius 0.5 mm, 6-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMRK.3.03.50.04.01 CN2K End mills for processing copper with corner radius 0.1 mm, 3-edged with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSMRK.3.03.63.06.01 CN2K End mills for processing copper with corner radius 0.1 mm, 3-edged with a diameter of 3 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRK.3.04.63.06.01 CN2K End mills for processing copper with corner radius 0.1 mm, 3-edged with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRK.3.05.63.06.01 CN2K End mills for processing copper with corner radius 0.1 mm, 3-fluted, with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRK.3.06.63.06.02 CN2K End mills for processing copper with corner radius 0.2 mm, 3-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSMRK.3.08.77.08.02 CN2K End mills for processing copper with corner radius 0.2 mm, 3-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSMRK.3.10.77.10.02 CN2K End mills for processing copper with corner radius 0.2 mm, 3-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSMRK.3.12.88.12.02 CN2K End mills for processing copper with corner radius 0.2 mm, 3-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSMRK.3.16.99.16.02 CN2K End mills for processing copper with corner radius 0.2 mm, 3-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSR.3.020.38.03 TS3K End mills for soft and hard milling, corner radius 0.2 mm, 3-edged with a diameter of 2 mm and a shaft diameter of 3 mm. |
|
Paul Horn DSR.3.030.38.03 TS3K End mills for soft and hard milling, corner radius 0.2 mm, 3-edged with a diameter of 3 mm and a shaft diameter of 3 mm. |
|
Paul Horn DSR.3.040.50.06 TS3K End mills for soft and hard milling, corner radius 0.2 mm, 3-edged with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSR.3.040.63.06 TS3K End mills for soft and hard milling, corner radius 0.2 mm, 3-edged with a diameter of 4 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSR.3.050.50.06 TS3K End mills for soft and hard milling, corner radius 0.2 mm, 3-fluted, with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSR.3.050.63.06 TS3K End mills for soft and hard milling, corner radius 0.2 mm, 3-fluted, with a diameter of 5 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSR.3.060.63.06 TS3K End mills for soft and hard milling, corner radius 0.3 mm, 3-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSR.3.080.63.08 TS3K End mills for soft and hard milling, corner radius 0.5 mm, 3-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSR.3.100.69.10 TS3K End mills for soft and hard milling, corner radius 0.5 mm, 3-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSR.3.120.77.12 TS3K End mills for soft and hard milling, corner radius 0.5 mm, 3-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSR.3.160.88.16 TS3K End mills for soft and hard milling, corner radius 0.5 mm, 3-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSRA.3.040.010.030 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.040.010.050 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.040.010.053 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.040.010.070 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.040.050.030 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.040.050.050 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.040.050.053 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.040.050.070 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.040.100.030 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.040.100.050 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.040.100.053 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.040.100.070 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 4 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.050.010.030 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.050.010.050 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.050.010.053 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.050.010.070 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.050.050.030 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.050.050.050 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.050.050.053 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.050.050.070 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.050.100.030 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.050.100.050 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.050.100.053 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.050.100.070 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 5 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.060.010.030 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.060.010.050 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.060.010.053 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.060.010.070 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.060.050.030 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.060.050.050 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.060.050.053 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.060.050.070 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.060.100.030 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.060.100.050 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.060.100.053 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.060.100.070 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.060.250.030 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.060.250.050 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.060.250.053 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.060.250.070 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 6 mm and a shaft diameter of 6 mm, center-tapping. |
|
Paul Horn DSRA.3.080.010.030 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm, center-tapping. |
|
Paul Horn DSRA.3.080.010.050 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm, center-tapping. |
|
Paul Horn DSRA.3.080.010.053 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm, center-tapping. |
|
Paul Horn DSRA.3.080.010.070 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm, center-tapping. |
|
Paul Horn DSRA.3.080.050.030 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm, center-tapping. |
|
Paul Horn DSRA.3.080.050.050 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm, center-tapping. |
|
Paul Horn DSRA.3.080.050.053 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm, center-tapping. |
|
Paul Horn DSRA.3.080.050.070 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm, center-tapping. |
|
Paul Horn DSRA.3.080.100.030 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm, center-tapping. |
|
Paul Horn DSRA.3.080.100.050 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm, center-tapping. |
|
Paul Horn DSRA.3.080.100.053 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm, center-tapping. |
|
Paul Horn DSRA.3.080.100.070 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm, center-tapping. |
|
Paul Horn DSRA.3.080.250.030 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm, center-tapping. |
|
Paul Horn DSRA.3.080.250.050 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm, center-tapping. |
|
Paul Horn DSRA.3.080.250.053 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm, center-tapping. |
|
Paul Horn DSRA.3.080.250.070 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 8 mm and a shaft diameter of 8 mm, center-tapping. |
|
Paul Horn DSRA.3.100.010.030 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm, Centre Cutting. |
|
Paul Horn DSRA.3.100.010.050 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm, Centre Cutting. |
|
Paul Horn DSRA.3.100.010.053 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm, Centre Cutting. |
|
Paul Horn DSRA.3.100.010.070 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm, Centre Cutting. |
|
Paul Horn DSRA.3.100.050.030 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm, Centre Cutting. |
|
Paul Horn DSRA.3.100.050.050 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm, Centre Cutting. |
|
Paul Horn DSRA.3.100.050.053 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm, Centre Cutting. |
|
Paul Horn DSRA.3.100.050.070 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm, Centre Cutting. |
|
Paul Horn DSRA.3.100.100.030 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm, Centre Cutting. |
|
Paul Horn DSRA.3.100.100.050 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm, Centre Cutting. |
|
Paul Horn DSRA.3.100.100.053 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm, Centre Cutting. |
|
Paul Horn DSRA.3.100.100.070 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm, Centre Cutting. |
|
Paul Horn DSRA.3.100.250.030 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm, Centre Cutting. |
|
Paul Horn DSRA.3.100.250.050 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm, Centre Cutting. |
|
Paul Horn DSRA.3.100.250.053 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm, Centre Cutting. |
|
Paul Horn DSRA.3.100.250.070 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 10 mm and a shaft diameter of 10 mm, Centre Cutting. |
|
Paul Horn DSRA.3.120.010.030 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm, Centre Cutting. |
|
Paul Horn DSRA.3.120.010.050 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm, Centre Cutting. |
|
Paul Horn DSRA.3.120.010.053 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm, Centre Cutting. |
|
Paul Horn DSRA.3.120.010.070 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm, Centre Cutting. |
|
Paul Horn DSRA.3.120.050.030 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm, Centre Cutting. |
|
Paul Horn DSRA.3.120.050.050 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm, Centre Cutting. |
|
Paul Horn DSRA.3.120.050.053 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm, Centre Cutting. |
|
Paul Horn DSRA.3.120.050.070 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm, Centre Cutting. |
|
Paul Horn DSRA.3.120.100.030 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm, Centre Cutting. |
|
Paul Horn DSRA.3.120.100.050 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm, Centre Cutting. |
|
Paul Horn DSRA.3.120.100.053 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm, Centre Cutting. |
|
Paul Horn DSRA.3.120.100.070 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm, Centre Cutting. |
|
Paul Horn DSRA.3.120.250.030 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm, Centre Cutting. |
|
Paul Horn DSRA.3.120.250.050 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm, Centre Cutting. |
|
Paul Horn DSRA.3.120.250.053 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm, Centre Cutting. |
|
Paul Horn DSRA.3.120.250.070 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm, Centre Cutting. |
|
Paul Horn DSRA.3.160.010.030 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm, Centre Cutting. |
|
Paul Horn DSRA.3.160.010.050 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm, Centre Cutting. |
|
Paul Horn DSRA.3.160.010.053 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm, Centre Cutting. |
|
Paul Horn DSRA.3.160.050.030 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm, Centre Cutting. |
|
Paul Horn DSRA.3.160.050.050 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm, Centre Cutting. |
|
Paul Horn DSRA.3.160.050.053 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm, Centre Cutting. |
|
Paul Horn DSRA.3.160.100.030 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm, Centre Cutting. |
|
Paul Horn DSRA.3.160.100.050 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm, Centre Cutting. |
|
Paul Horn DSRA.3.160.100.053 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm, Centre Cutting. |
|
Paul Horn DSRA.3.160.250.030 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm, Centre Cutting. |
|
Paul Horn DSRA.3.160.250.050 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm, Centre Cutting. |
|
Paul Horn DSRA.3.160.250.053 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm, Centre Cutting. |
|
Paul Horn DSRA.3.160.400.030 MG3K End mills for machining aluminum, corner radius 4 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm, Centre Cutting. |
|
Paul Horn DSRA.3.160.400.050 MG3K End mills for machining aluminum, corner radius 4 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm, Centre Cutting. |
|
Paul Horn DSRA.3.160.400.053 MG3K End mills for machining aluminum, corner radius 4 mm, 2 cutting edges with a diameter of 16 mm and a shaft diameter of 16 mm, Centre Cutting. |
|
Paul Horn DSRA.3.200.010.027 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 20 mm and a shaft diameter of 20 mm, Centre Cutting. |
|
Paul Horn DSRA.3.200.010.050 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 20 mm and a shaft diameter of 20 mm, Centre Cutting. |
|
Paul Horn DSRA.3.200.010.053 MG3K End mills for machining aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 20 mm and a shaft diameter of 20 mm, Centre Cutting. |
|
Paul Horn DSRA.3.200.050.027 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 20 mm and a shaft diameter of 20 mm, Centre Cutting. |
|
Paul Horn DSRA.3.200.050.050 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 20 mm and a shaft diameter of 20 mm, Centre Cutting. |
|
Paul Horn DSRA.3.200.050.053 MG3K End mills for machining aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 20 mm and a shaft diameter of 20 mm, Centre Cutting. |
|
Paul Horn DSRA.3.200.100.027 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 20 mm and a shaft diameter of 20 mm, Centre Cutting. |
|
Paul Horn DSRA.3.200.100.050 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 20 mm and a shaft diameter of 20 mm, Centre Cutting. |
|
Paul Horn DSRA.3.200.100.053 MG3K End mills for machining aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 20 mm and a shaft diameter of 20 mm, Centre Cutting. |
|
Paul Horn DSRA.3.200.250.027 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 20 mm and a shaft diameter of 20 mm, Centre Cutting. |
|
Paul Horn DSRA.3.200.250.050 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 20 mm and a shaft diameter of 20 mm, Centre Cutting. |
|
Paul Horn DSRA.3.200.250.053 MG3K End mills for machining aluminum, corner radius 2.5 mm, 2 cutting edges with a diameter of 20 mm and a shaft diameter of 20 mm, Centre Cutting. |
|
Paul Horn DSRA.3.200.400.027 MG3K End mills for machining aluminum, corner radius 4 mm, 2 cutting edges with a diameter of 20 mm and a shaft diameter of 20 mm, Centre Cutting. |
|
Paul Horn DSRA.3.200.400.050 MG3K End mills for machining aluminum, corner radius 4 mm, 2 cutting edges with a diameter of 20 mm and a shaft diameter of 20 mm, Centre Cutting. |
|
Paul Horn DSRA.3.200.400.053 MG3K End mills for machining aluminum, corner radius 4 mm, 2 cutting edges with a diameter of 20 mm and a shaft diameter of 20 mm, Centre Cutting. |
|
Paul Horn DSRF.3.06.63.06.25 TS3K End mills as Schruppfäser serrated for soft and hard milling, Eckfase 0.25mm, 3 flutes with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSRF.3.08.63.08.50 TS3K End mills as Schruppfäser serrated for soft and hard milling, Eckfase 0.5 mm, 3-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSRF.3.10.69.10.50 TS3K End mills as Schruppfäser serrated for soft and hard milling, Eckfase 0.5 mm, 3-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSRF.3.12.77.12.50 TS3K End mills as Schruppfäser serrated for soft and hard milling, Eckfase 0.5 mm, 3-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSRF.3.16.88.16.10 TS3K End mills as Schruppfäser serrated for soft and hard milling, Eckfase 0 mm, 3-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSRR.3.06.63.06.03 TS3K End mills as Schruppfäser serrated for soft and hard milling, corner radius 0.3 mm, 3-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSRR.3.08.63.08.05 TS3K End mills as Schruppfäser serrated for soft and hard milling, corner radius 0.5 mm, 3-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSRR.3.10.69.10.05 TS3K End mills as Schruppfäser serrated for soft and hard milling, corner radius 0.5 mm, 3-edged with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSRR.3.12.77.12.05 TS3K End mills as Schruppfäser serrated for soft and hard milling, corner radius 0.5 mm, 3-edged with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSRR.3.16.88.16.05 TS3K End mills as Schruppfäser serrated for soft and hard milling, corner radius 0.5 mm, 3-edged with a diameter of 16 mm and a shaft diameter of 16 mm. |
|
Paul Horn DSRV.4.03.38.03 TS3K End mills as Schlichtfäser for soft and hard milling, corner radius 0.2 mm, 4-edged, with a diameter of 3 mm and a shaft diameter of 3 mm. |
|
Paul Horn DSRV.4.04.50.04 TS3K End mills as Schlichtfäser for soft and hard milling, corner radius 0.2 mm, 4-edged, with a diameter of 4 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSRV.4.05.50.05 TS3K End mills as Schlichtfäser for soft and hard milling, corner radius 0.2 mm, 4-edged, with a diameter of 5 mm and a shaft diameter of 5 mm. |
|
Paul Horn DSRV.4.06.63.06 TS3K End mills as Schlichtfäser for soft and hard milling, corner radius 0.3 mm, 4-edged, with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSRV.4.08.63.08 TS3K End mills as Schlichtfäser for soft and hard milling, corner radius 0.5 mm, 4-edged, with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSRV.4.10.69.10 TS3K End mills as Schlichtfäser for soft and hard milling, corner radius 0.5 mm, 4-edged, with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSRV.4.12.77.12 TS3K End mills as Schlichtfäser for soft and hard milling, corner radius 1 mm, 4 cutting edges with a diameter of 12 mm and a shaft diameter of 12 mm. |
