|
Paul Horn RA210.20.9513.15 Tool holders with shank 20.00 mm Width x 20.00 mm height for axial grooving of 95.00 to 130.00 mm outer groove diameter at a cutting depth of up to 15.00 mm and a maximum groove width of 5.00 mm, matc |
|
Paul Horn RA210.25.1318.14 Tool holders with shank 25.00 mm wide x 25.00 mm height for axial grooving from 130.00 to 180.00 mm outer groove diameter at a cutting depth of up to 15.00 mm and a maximum groove width of 4.00 mm, ma |
|
Paul Horn RA210.25.1318.15 Tool holders with shank 25.00 mm wide x 25.00 mm height for axial grooving from 130.00 to 180.00 mm outer groove diameter at a cutting depth of up to 15.00 mm and a maximum groove width of 5.00 mm, ma |
|
Paul Horn RA210.25.9513.14 Tool holders with shank 25.00 mm wide x 25.00 mm height for axial grooving of 95.00 to 130.00 mm outer groove diameter at a cutting depth of up to 15.00 mm and a maximum groove width of 4.00 mm, match |
|
Paul Horn RA210.25.9513.15 Tool holders with shank 25.00 mm wide x 25.00 mm height for axial grooving of 95.00 to 130.00 mm outer groove diameter at a cutting depth of up to 15.00 mm and a maximum groove width of 5.00 mm, match |
|
Paul Horn RA210.32.1318.15 Tool holders type |
|
Paul Horn RA226.20.1318.04 Tool holders with shank 20.00 mm Width x 20.00 mm height for axial grooving from 130.00 to 180.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 4.00 mm, mat |
|
Paul Horn RA226.20.1318.05 Tool holders with shank 20.00 mm Width x 20.00 mm height for axial grooving from 130.00 to 180.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 5.00 mm, mat |
|
Paul Horn RA226.20.9513.04 Tool holders with shank 20.00 mm Width x 20.00 mm height for axial grooving of 95.00 to 130.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 4.00 mm, matchi |
|
Paul Horn RA226.20.9513.05 Tool holders with shank 20.00 mm Width x 20.00 mm height for axial grooving of 95.00 to 130.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 5.00 mm, matchi |
|
Paul Horn RA226.25.1318.04 Tool holders with shank 25.00 mm wide x 25.00 mm height for axial grooving from 130.00 to 180.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 4.00 mm, matc |
|
Paul Horn RA226.25.1318.05 Tool holders with shank 25.00 mm wide x 25.00 mm height for axial grooving from 130.00 to 180.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 5.00 mm, matc |
|
Paul Horn RA226.25.9513.04 Tool holders with shank 25.00 mm wide x 25.00 mm height for axial grooving of 95.00 to 130.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 4.00 mm, matchin |
|
Paul Horn RA226.25.9513.05 Tool holders with shank 25.00 mm wide x 25.00 mm height for axial grooving of 95.00 to 130.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 5.00 mm, matchin |
|
Paul Horn RA315.0815.45.04L TH35 Indexable insert for axial grooving from 8 mm outer groove diameter at a penetration depth of 1.6 mm and a groove width of 1.5 mm, to a suitable clamp holder for. B. 356, execution law. |
|
Paul Horn RA315.0815.45.04L TN35 Indexable insert for axial grooving from 8 mm outer groove diameter at a penetration depth of 1.6 mm and a groove width of 1.5 mm, to a suitable clamp holder for. B. 356, execution law. |
|
Paul Horn RA315.1220.45.05L TH35 Indexable insert for axial grooving from 12 mm outer groove diameter at a penetration depth of 1.8 mm and a groove width of 2 mm, to a suitable clamp holder for. B. 356, execution law. |
|
Paul Horn RA315.1220.45.05L TN35 Indexable insert for axial grooving from 12 mm outer groove diameter at a penetration depth of 1.8 mm and a groove width of 2 mm, to a suitable clamp holder for. B. 356, execution law. |
|
Paul Horn RA315.2015.02L TH35 The indexable insert with a cutting width of 1.5 mm is suitable for grooving up to 2 mm depth. |
|
Paul Horn RA315.2015.02R TH35 The indexable insert with a cutting width of 1.5 mm is suitable for grooving up to 2 mm depth. |
|
Paul Horn RA315.2024.45.06L TH35 Indexable insert for axial grooving from 20 mm outer groove diameter at a penetration depth of 2 mm and a groove width of 2.4 mm, to a suitable clamp holder for. B. 356, execution law. |
|
Paul Horn RA315.2024.45.06L TN35 Indexable insert for axial grooving from 20 mm outer groove diameter at a penetration depth of 2 mm and a groove width of 2.4 mm, to a suitable clamp holder for. B. 356, execution law. |
|
Paul Horn RA315.3020.02L TH35 The indexable insert with a cutting width of 2 mm is suitable for grooving up to 3 mm in depth. |
|
Paul Horn RA315.3020.02R TH35 The indexable insert with a cutting width of 2 mm is suitable for grooving up to 3 mm in depth. |
|
Paul Horn RA315.3030.02L TH35 The indexable insert with a cutting width of 3 mm is suitable for grooving up to 3 mm in depth. |
|
Paul Horn RA315.3030.02R TH35 The indexable insert with a cutting width of 3 mm is suitable for grooving up to 3 mm in depth. |
|
Paul Horn RAH25A.12.1520.02 Toolholder with shank 12 mm width x 12 mm height for axial grooving of 15 to 20 mm outer groove diameter at a penetration depth of 12 mm and a maximum groove width of 2 mm, matching indexable insert t |
|
Paul Horn RAH25A.12.1520.03 Toolholder with shank 12 mm width x 12 mm height for axial grooving of 15 to 20 mm outer groove diameter at a penetration depth of 13 mm and a maximum groove width of 3 mm, matching indexable insert t |
|
Paul Horn RAH25A.12.2025.02 Toolholder with shank 12 mm width x 12 mm height for axial grooving of 20 to 25 mm outer groove diameter at a penetration depth of 12 mm and a maximum groove width of 2 mm, matching indexable insert t |
|
Paul Horn RAH25A.12.2025.03 Toolholder with shank 12 mm width x 12 mm height for axial grooving of 20 to 25 mm outer groove diameter at a penetration depth of 14 mm and a maximum groove width of 3 mm, matching indexable insert t |
|
Paul Horn RAH25A.12.2530.02 Toolholder with shank 12 mm width x 12 mm height for axial grooving of 25 to 30 mm outer groove diameter at a penetration depth of 13 mm and a maximum groove width of 2 mm, matching indexable insert t |
|
Paul Horn RAH25A.12.2530.03 Toolholder with shank 12 mm width x 12 mm height for axial grooving of 25 to 30 mm outer groove diameter at a penetration depth of 15 mm and a maximum groove width of 3 mm, matching indexable insert t |
|
Paul Horn RAH25A.16.1520.02 Toolholder with shank 16 mm width x 16 mm height for axial grooving of 15 to 20 mm outer groove diameter at a penetration depth of 12 mm and a maximum groove width of 2 mm, matching indexable insert t |
|
Paul Horn RAH25A.16.1520.03 Toolholder with shank 16 mm width x 16 mm height for axial grooving of 15 to 20 mm outer groove diameter at a penetration depth of 13 mm and a maximum groove width of 3 mm, matching indexable insert t |
|
Paul Horn RAH25A.16.2025.02 Toolholder with shank 16 mm width x 16 mm height for axial grooving of 20 to 25 mm outer groove diameter at a penetration depth of 12 mm and a maximum groove width of 2 mm, matching indexable insert t |
|
Paul Horn RAH25A.16.2025.03 Toolholder with shank 16 mm width x 16 mm height for axial grooving of 20 to 25 mm outer groove diameter at a penetration depth of 14 mm and a maximum groove width of 2 mm, matching indexable insert t |
|
Paul Horn RAH25A.16.2530.02 Toolholder with shank 16 mm width x 16 mm height for axial grooving of 25 to 30 mm outer groove diameter at a penetration depth of 13 mm and a maximum groove width of 2 mm, matching indexable insert t |
|
Paul Horn RAH25A.16.2530.03 Toolholder with shank 16 mm width x 16 mm height for axial grooving of 25 to 30 mm outer groove diameter at a penetration depth of 15 mm and a maximum groove width of 3 mm, matching indexable insert t |
|
Paul Horn RAH25A.20.1520.02 Toolholder with shank 20 mm width x 20 mm height for axial grooving of 15 to 20 mm outer groove diameter at a penetration depth of 12 mm and a maximum groove width of 2 mm, matching indexable insert t |
|
Paul Horn RAH25A.20.1520.03 Toolholder with shank 20 mm width x 20 mm height for axial grooving of 15 to 20 mm outer groove diameter at a penetration depth of 13 mm and a maximum groove width of 3 mm, matching indexable insert t |
|
Paul Horn RAH25A.20.2025.02 Toolholder with shank 20 mm width x 20 mm height for axial grooving of 20 to 25 mm outer groove diameter at a penetration depth of 12 mm and a maximum groove width of 2 mm, matching indexable insert t |
|
Paul Horn RAH25A.20.2025.03 Toolholder with shank 20 mm width x 20 mm height for axial grooving of 20 to 25 mm outer groove diameter at a penetration depth of 14 mm and a maximum groove width of 3 mm, matching indexable insert t |
|
Paul Horn RAH25A.20.2530.02 Toolholder with shank 20 mm width x 20 mm height for axial grooving of 25 to 30 mm outer groove diameter at a penetration depth of 13 mm and a maximum groove width of 2 mm, matching indexable insert t |
|
Paul Horn RAH25A.20.2530.03 Toolholder with shank 20 mm width x 20 mm height for axial grooving of 25 to 30 mm outer groove diameter at a penetration depth of 15 mm and a maximum groove width of 3 mm, matching indexable insert t |
|
Paul Horn RAK220.1318.04 Cassette for axial grooving from 130.00 to 180.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.1318.05 Cassette for axial grooving from 130.00 to 180.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.1318.06 Cassette for axial grooving from 130.00 to 180.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 6:00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.1318.14 Cassette for axial grooving from 130.00 to 180.00 mm outer groove diameter at a cutting depth of up to 15.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 229, execution law |
|
Paul Horn RAK220.1318.15 Cassette for axial grooving from 130.00 to 180.00 mm outer groove diameter at a cutting depth of up to 15.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 229, execution law |
|
Paul Horn RAK220.1318.16 Cassette for axial grooving from 130.00 to 180.00 mm outer groove diameter at a cutting depth of up to 15.00 mm and a maximum groove width of 6:00 mm, matching indexable insert type 229, execution law |
|
Paul Horn RAK220.1830.04 Cassette for axial grooving from 180.00 to 300.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.1830.05 Cassette for axial grooving from 180.00 to 300.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.1830.06 Cassette for axial grooving from 180.00 to 300.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 6:00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.1830.14 Cassette for axial grooving from 180.00 to 300.00 mm outer groove diameter at a cutting depth of up to 15.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 229, execution law |
|
Paul Horn RAK220.1830.15 Cassette for axial grooving from 180.00 to 300.00 mm outer groove diameter at a cutting depth of up to 15.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 229, execution law |
|
Paul Horn RAK220.1830.16 Cassette for axial grooving from 180.00 to 300.00 mm outer groove diameter at a cutting depth of up to 15.00 mm and a maximum groove width of 6:00 mm, matching indexable insert type 229, execution law |
|
Paul Horn RAK220.3000.04 Cassette for axial grooving from 300.00 to 1000.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.3000.05 Cassette for axial grooving from 300.00 to 1000.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.3000.06 Cassette for axial grooving from 300.00 to 1000.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 6:00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.6075.05 Cassette for axial grooving from 60.00 to 75.00 mm outer groove diameter at a penetration depth from 10.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.6075.06 Cassette for axial grooving from 60.00 to 75.00 mm outer groove diameter at a penetration depth from 10.00 mm and a maximum groove width of 6:00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.6075.15 Cassette for axial grooving from 60.00 to 75.00 mm outer groove diameter at a penetration depth from 10.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.6575.04 Cassette for axial grooving from 65.00 to 75.00 mm outer groove diameter at a penetration depth from 10.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.6575.14 Cassette for axial grooving from 65.00 to 75.00 mm outer groove diameter at a penetration depth from 10.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.7595.04 Cassette for axial grooving from 75.00 to 95.00 mm outer groove diameter at a penetration depth of 15.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.7595.05 Cassette for axial grooving from 75.00 to 95.00 mm outer groove diameter at a penetration depth of 17.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.7595.06 Cassette for axial grooving from 75.00 to 95.00 mm outer groove diameter at a penetration depth of 17.00 mm and a maximum groove width of 6.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.7595.14 Cassette for axial grooving from 75.00 to 95.00 mm outer groove diameter at a penetration depth of 15.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.7595.15 Cassette for axial grooving from 75.00 to 95.00 mm outer groove diameter at a cutting depth of up to 15.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.7595.16 Cassette for axial grooving from 75.00 to 95.00 mm outer groove diameter at a cutting depth of up to 15.00 mm and a maximum groove width of 6:00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.9513.04 Cassette for axial grooving of 95.00 to 130.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.9513.05 Cassette for axial grooving of 95.00 to 130.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.9513.06 Cassette for axial grooving of 95.00 to 130.00 mm outer groove diameter at a penetration depth of 25.00 mm and a maximum groove width of 6:00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.9513.14 Cassette for axial grooving of 95.00 to 130.00 mm outer groove diameter at a cutting depth of up to 15.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.9513.15 Cassette for axial grooving of 95.00 to 130.00 mm outer groove diameter at a cutting depth of up to 15.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK220.9513.16 Cassette for axial grooving of 95.00 to 130.00 mm outer groove diameter at a cutting depth of up to 15.00 mm and a maximum groove width of 6:00 mm, matching indexable insert type 229, execution law. |
|
Paul Horn RAK224.1113.03 Cassette for axial grooving from 110.00 to 130.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 3.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.1318.03 Cassette for axial grooving from 130.00 to 180.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 3.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.1318.04 Cassette for axial grooving from 130.00 to 180.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.1318.05 Cassette for axial grooving from 130.00 to 180.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.1318.06 Cassette for axial grooving from 130.00 to 180.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 6:00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.1830.03 Cassette for axial grooving from 180.00 to 300.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 3.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.1830.04 0 for axial grooving from 180.00 to 300.00 mm outer groove diameter at a cutting depth of 0 mm and a maximum groove width of 0 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.1830.05 0 for axial grooving from 180.00 to 300.00 mm outer groove diameter at a cutting depth of 0 mm and a maximum groove width of 0 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.1830.06 0 for axial grooving from 180.00 to 300.00 mm outer groove diameter at a cutting depth of 0 mm and a maximum groove width of 0 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.3000.03 Cassette for axial grooving from 300 to 1000 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 3.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.3000.04 Cassette for axial grooving from 300.00 to 1000.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.3000.05 Cassette for axial grooving from 300.00 to 1000.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.3847.04 Cassette for axial grooving of 38.00 to 47.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.3847.05 Cassette for axial grooving of 38.00 to 47.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.4760.04 Cassette for axial grooving of 47.00 to 60.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.4760.05 Cassette for axial grooving of 47.00 to 60.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.5060.03 Cassette for axial grooving from 50.00 to 60.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 3.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.6075.03 Cassette for axial grooving from 60.00 to 75.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 3.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.6075.04 Cassette for axial grooving from 60.00 to 75.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.6075.05 Cassette for axial grooving from 60.00 to 75.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.7590.03 Cassette for axial grooving from 75.00 to 90.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 3.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.7590.04 Cassette for axial grooving from 75.00 to 90.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.7590.05 Cassette for axial grooving from 75.00 to 90.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.9011.03 Cassette for axial grooving of 90.00 to 110.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 3.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.9013.04 Cassette for axial grooving of 90.00 to 130.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 4.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.9013.05 Cassette for axial grooving of 90.00 to 130.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 5.00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK224.9013.06 Cassette for axial grooving of 90.00 to 130.00 mm outer groove diameter at a penetration depth of 14.00 mm and a maximum groove width of 6:00 mm, matching indexable insert type 224, execution law. |
|
Paul Horn RAK25A.1520.02.IK Cassette for axial grooving of 15 to 20 mm outer groove diameter at a penetration depth of 12 mm and a maximum groove width of 2 mm, matching indexable insert type S25A, execution law. |
|
Paul Horn RAK25A.2025.02.IK Cassette for axial grooving of 20 to 25 mm outer groove diameter at a penetration depth of 12 mm and a maximum groove width of 2 mm, matching indexable insert type S25A, execution law. |
|
Paul Horn RAK25A.2025.03.IK Cassette for axial grooving of 20 to 25 mm outer groove diameter at a penetration depth of 14 mm and a maximum groove width of 3 mm, matching indexable insert type S25A, execution law. |
|
Paul Horn RAK25A.2025.04.IK Cassette for axial grooving of 20 to 25 mm outer groove diameter at a penetration depth of 16 mm and a maximum groove width of 4 mm, matching indexable insert type S25A, execution law. |
|
Paul Horn RAK25A.2530.02.IK Cassette for axial grooving of 25 to 30 mm outer groove diameter at a penetration depth of 13 mm and a maximum groove width of 2 mm, matching indexable insert type S25A, execution law. |
|
Paul Horn RAK25A.2530.03.IK Cassette for axial grooving of 25 to 30 mm outer groove diameter at a penetration depth of 15 mm and a maximum groove width of 3 mm, matching indexable insert type S25A, execution law. |
|
Paul Horn RAK25A.2530.04.IK Cassette for axial grooving of 25 to 30 mm outer groove diameter at a penetration depth of 17 mm and a maximum groove width of 4 mm, matching indexable insert type S25A, execution law. |
|
Paul Horn RAK25A.3040.03.IK Cassette for axial grooving of 30 to 40 mm outer groove diameter at a penetration depth of 16 mm and a maximum groove width of 3 mm, matching indexable insert type S25A, execution law. |
|
Paul Horn RAK25A.3040.04.IK Cassette for axial grooving of 30 to 40 mm outer groove diameter at a penetration depth of 18 mm and a maximum groove width of 4 mm, matching indexable insert type S25A, execution law. |
|
Paul Horn RAK25A.4050.03.IK Cassette for axial grooving of 40 to 50 mm outer groove diameter at a penetration depth of 18 mm and a maximum groove width of 3 mm, matching indexable insert type S25A, execution law. |
|
Paul Horn RAK25A.4050.04.IK Cassette for axial grooving of 40 to 50 mm outer groove diameter at a penetration depth of 20 mm and a maximum groove width of 4 mm, matching indexable insert type S25A, execution law. |
|
Paul Horn RAM.2518.040 Break Pairing URMA friction system of Beta module 25 by Alpha module 18.5 |
|
Paul Horn RB105.0016.12.2 Toolholder as boring bar with clamping diameter 16.00mm for receiving inserts Type 105, Type law. |
|
Paul Horn RB105.0020.12.2 Toolholder as boring bar with clamping diameter 20.00 mm for receiving inserts Type 105, Type law. |
|
Paul Horn RB105.00C3.2.2.01 Toolholder with terminal HORN polygonal shank ISO 26623 for receiving inserts Type 105, Type law. |
|
Paul Horn RB105.00C3.2.2.02 Toolholder with terminal HORN polygonal shank ISO 26623 for receiving inserts Type 105, Type law. |
|
Paul Horn RB105.00C3.20.1.01 Toolholder as boring bar with clamping diameter 0 mm for receiving inserts Type 105, Type law. |
|
Paul Horn RB105.00C4.2.2.01 Toolholder with terminal HORN polygonal shank ISO 26623 for receiving inserts Type 105, Type law. |
|
Paul Horn RB105.00C4.2.2.02 Toolholder with terminal HORN polygonal shank ISO 26623 for receiving inserts Type 105, Type law. |
|
Paul Horn RB105.00C4.20.1.01 Toolholder with terminal HORN polygonal shank ISO 26623 for receiving inserts Type 105, Type law. |
|
Paul Horn RB105.00C4.20.1.02 Toolholder with terminal HORN polygonal shank ISO 26623 for receiving inserts Type 105, Type law. |
|
Paul Horn RB105.00C5.20.1.01 Toolholder with terminal HORN polygonal shank ISO 26623 for receiving inserts Type 105, Type law. |
|
Paul Horn RB105.00C6.20.1.01 Toolholder with terminal HORN polygonal shank ISO 26623 for receiving inserts Type 105, Type law. |
|
Paul Horn RB105.00C6.20.1.02 Toolholder with terminal HORN polygonal shank ISO 26623 for receiving inserts Type 105, Type law. |
|
Paul Horn RB105.MD12.4.13 Toolholder as boring bar with clamping diameter 12.00 mm for receiving inserts type 105 for mirror turning, execution law. |
|
Paul Horn RB105.MD12.6.13 Toolholder as boring bar with clamping diameter 12.00 mm for receiving inserts type 105 for mirror turning, execution law. |
|
Paul Horn RB105.MD12.8.13 Toolholder as boring bar with clamping diameter 12.00 mm for receiving inserts type 105 for mirror turning, execution law. |
|
Paul Horn RB106.0012.01 Toolholder with shaft diameter 12.00 mm and 1 clamping area for aligning the projection length is 14 mm, repairable, fits to cutting type R106. |
|
Paul Horn RB106.0012.02 Toolholder with shaft diameter 12.00 mm and 1 clamping area for aligning the projection length is 20 mm, repairable, fits to cutting type R106. |
|
Paul Horn RB106.0012.03 Toolholder with shaft diameter 12.00 mm and 1 clamping area for aligning the projection length is 26 mm, repairable, fits to cutting type R106. |
|
Paul Horn RB107.0012.01 Toolholder with shaft diameter 12.00 mm and 1 clamping area for aligning the projection length is 18 mm, repairable, fits to cutting type 107th |
|
Paul Horn RB107.0012.02 Toolholder with shaft diameter 12.00 mm and 1 clamping area for aligning, repairable, fits to cutting type 107th |
|
Paul Horn RB107.0012.03 Toolholder with shaft diameter 12.00 mm and 1 clamping area for aligning, repairable, fits to cutting type 107th |
|
Paul Horn RB109.0016.14.2 Toolholder with shank diameters 16.00mm and 1 clamping area for aligning, repairable, fits to cutting type 109th |
|
Paul Horn RB10P.0012.00 Toolholder with shaft diameter 12.00 mm and 1 clamping area for aligning the projection length is 12.50 mm, repairable, fits to cutting type 10P. |
|
Paul Horn RB10P.0012.00S Toolholder with shaft diameter 12.00 mm and 1 clamping area for aligning the projection length is 12.50 mm, repairable, fits to cutting type 10P. |
|
Paul Horn RB10P.0012.01 Toolholder with shaft diameter 12.00 mm and 1 clamping area for aligning the projection length is 21.00 mm, repairable, fits to cutting type 10P. |
|
Paul Horn RB10P.0012.01S Toolholder with shaft diameter 12.00 mm and 1 clamping area for aligning the projection length is 21.00 mm, repairable, fits to cutting type 10P. |
|
Paul Horn RB10P.0012.02 Toolholder with shaft diameter 12.00 mm and 1 clamping area for aligning the projection length is 30.00 mm, repairable, fits to cutting type 10P. |
|
Paul Horn RB10P.0012.02S Toolholder with shaft diameter 12.00 mm and 1 clamping area for aligning the projection length is 30.00 mm, repairable, fits to cutting type 10P. |
|
Paul Horn RB10P.0012.03 Toolholder with shaft diameter 12.00 mm and 1 clamping area for aligning the projection length is 42 mm, repairable, fits to cutting type 10P. |
|
Paul Horn RB10P.0012.2.00 Toolholder with shaft diameter 12.00 mm and 1 clamping area for aligning the projection length is 12.50 mm, repairable, fits to cutting type 10P. |
|
Paul Horn RB10P.0012.2.01 Toolholder with shaft diameter 12.00 mm and 1 clamping area for aligning the projection length is 21.00 mm, repairable, fits to cutting type 10P. |
|
Paul Horn RB10P.0012.2.02 Toolholder with shaft diameter 12.00 mm and 1 clamping area for aligning the projection length is 30.00 mm, repairable, fits to cutting type 10P. |
|
Paul Horn RB10P.0012.2.03 Toolholder with shaft diameter 12.00 mm and 1 clamping area for aligning the projection length is 42 mm, repairable, fits to cutting type 10P. |
|
Paul Horn RB110.0016.16.2 Toolholder with shank diameters 16.00mm and 1 clamping area for aligning, suitable to cutting type 110th |
|
Paul Horn RB110.0020.16.2 Toolholder with shaft diameter 20.00 mm and 1 clamping area for aligning, suitable to cutting type 110th |
|
Paul Horn RB110.00C3.2.2.02 Toolholder with terminal HORN polygonal shank ISO 26623 for receiving inserts Type 110, Type law. |
|
Paul Horn RB110.00C3.22.1.02 Toolholder with terminal HORN polygonal shank ISO 26623 for receiving inserts Type 110, Type law. |
|
Paul Horn RB110.00C4.2.2.02 Toolholder with terminal HORN polygonal shank ISO 26623 for receiving inserts Type 110, Type law. |
|
Paul Horn RB110.00C4.22.1.02 Toolholder with terminal HORN polygonal shank ISO 26623 for receiving inserts Type 110, Type law. |
|
Paul Horn RB110.00C5.22.1.02 Toolholder with terminal HORN polygonal shank ISO 26623 for receiving inserts Type 110, Type law. |
|
Paul Horn RB110.00C6.22.1.02 Toolholder with terminal HORN polygonal shank ISO 26623 for receiving inserts Type 110, Type law. |
|
Paul Horn RB119.0016.1.32 Toolholder as a drill with shank diameters 16.00mm and 25.00 mm overhang for receiving indexable inserts type S119 with the smallest bore diameter 16.00mm. |
|
Paul Horn RB119.0016.1.33 Toolholder as a drill with shank diameters 16.00mm and 25.00 mm overhang for receiving indexable inserts type S119 with the smallest bore diameter 16.00mm. |
|
Paul Horn RB11P.0012.00 Toolholder as boring bar shank diameter 12.00 mm and overhang 15:00 mm for receiving indexable type 11P, with the smallest bore diameter mm 10:50. |
|
Paul Horn RB11P.0012.00S Toolholder as boring bar shank diameter 12.00 mm and overhang 15:00 mm for receiving indexable type 11P, with the smallest bore diameter mm 10:50. |
|
Paul Horn RB11P.0012.01 Toolholder as boring bar shank diameter 12.00 mm and 26.00 mm overhang for receiving indexable type 11P, with the smallest bore diameter mm 10:50. |
|
Paul Horn RB11P.0012.01S Toolholder as boring bar shank diameter 12.00 mm and 26.00 mm overhang for receiving indexable type 11P, with the smallest bore diameter mm 10:50. |
|
Paul Horn RB11P.0012.02 Toolholder as boring bar shank diameter 12.00 mm and 37.00 mm overhang for receiving indexable type 11P, with the smallest bore diameter mm 10:50. |
|
Paul Horn RB11P.0012.02S Toolholder as boring bar shank diameter 12.00 mm and 37.00 mm overhang for receiving indexable type 11P, with the smallest bore diameter mm 10:50. |
|
Paul Horn RB11P.0012.03 Toolholder as boring bar shank diameter 12.00 mm and 50.00 mm overhang for receiving indexable type 11P, with the smallest bore diameter mm 10:50. |
|
Paul Horn RB11P.0012.2.00 Toolholder as boring bar shank diameter 12.00 mm and overhang 15:00 mm for receiving indexable type 11P, with the smallest bore diameter mm 10:50. |
|
Paul Horn RB11P.0012.2.01 Toolholder as boring bar shank diameter 12.00 mm and 26.00 mm overhang for receiving indexable type 11P, with the smallest bore diameter mm 10:50. |
|
Paul Horn RB11P.0012.2.02 Toolholder as boring bar shank diameter 12.00 mm and 37.00 mm overhang for receiving indexable type 11P, with the smallest bore diameter mm 10:50. |
|
Paul Horn RB11P0012203 Toolholder as boring bar shank diameter 12.00 mm and 50.00 mm overhang for receiving indexable type 11P, with the smallest bore diameter mm 10:50. |
|
Paul Horn RB18P.0012.00 Toolholder as boring bar shank diameter 12.00 mm and 25.00 mm overhang for receiving indexable type 18P, with the smallest bore diameter mm 18:00. |
|
Paul Horn RB18P.0012.01 Toolholder as boring bar shank diameter 12.00 mm and 40.00 mm overhang for receiving indexable type 18P, with the smallest bore diameter mm 18:00. |
|
Paul Horn RB18P.0016.00 Toolholder as a drill with shank diameters 16.00mm and 25.00 mm overhang for receiving indexable type 18P, with the smallest bore diameter mm 18:00. |
|
Paul Horn RB18P.0016.01 Toolholder as a drill with shank diameters 16.00mm and 40.00 mm overhang for receiving indexable type 18P, with the smallest bore diameter mm 18:00. |
|
Paul Horn RB18P.0016.02 Toolholder as a drill with shank diameters 16.00mm and 56.00 mm overhang for receiving indexable type 18P, with the smallest bore diameter mm 18:00. |
|
Paul Horn RB18P.0016.03 Toolholder as a drill with shank diameters 16.00mm and 80.00 mm overhang for receiving indexable type 18P, with the smallest bore diameter mm 18:00. |
|
Paul Horn RB209.0016.1.02.IK Toolholder as a drill with shank diameters 16.00mm and 30mm projection length for receiving indexable inserts type S209 with the smallest bore diameter 16 mm. |
|
Paul Horn RB209.0016.1.025.IK Tool holders type |
|
Paul Horn RB209.0016.1.03.IK Tool holders type |
|
Paul Horn RB209.0020.1.12.IK Toolholder as a drill with shaft diameter 20 mm and 30 mm overhang for receiving indexable inserts type S209 with the smallest bore diameter 18 mm. |
|
Paul Horn RB209.0020.1.125.IK Tool holders type |
|
Paul Horn RB209.0020.1.13.IK Tool holders type |
|
Paul Horn RB216.0020.1.22.IK Toolholder as a drill with shaft diameter 20 mm and 30 mm overhang for receiving indexable inserts type S216 with the smallest bore diameter 20 mm. |
|
Paul Horn RB216.0020.1.225.IK Toolholder round shank with internal coolant |
|
Paul Horn RB216.0020.1.23.IK Toolholder round shank with internal coolant |
|
Paul Horn RB216.0020.1.24.IK Toolholder round shank with internal coolant |
|
Paul Horn RB216.0025.2.22.IK Toolholder as a drill with shaft diameter 25 mm and 50 mm overhang for receiving indexable inserts type S216 with the smallest bore diameter 25 mm. |
|
Paul Horn RB216.0025.2.225.IK Toolholder round shank with internal coolant |
|
Paul Horn RB216.0025.2.23.IK Toolholder round shank with internal coolant |
|
Paul Horn RB216.0025.2.24.IK Toolholder round shank with internal coolant |
|
Paul Horn RB216.0025.23.1.22.IK Toolholder as a drill with shaft diameter 25 mm and 30 mm overhang for receiving indexable inserts type S216 with the smallest bore diameter 23 mm. |
|
Paul Horn RB216.0025.23.1.225.IK Toolholder round shank with internal coolant |
|
Paul Horn RB216.0025.23.1.23.IK Toolholder round shank with internal coolant |
|
Paul Horn RB216.0025.23.1.24.IK Toolholder round shank with internal coolant |
|
Paul Horn RB216.0025.23.1.25.IK Toolholder round shank with internal coolant |
|
Paul Horn RB216.0025.23.1.26.IK Toolholder round shank with internal coolant |
|
Paul Horn RB223.0016.0.42 Toolholder as boring bar shank diameter 16.00mm for receiving indexable inserts type S223 with the smallest bore diameter 22.00 mm. |
|
Paul Horn RB223.0016.0.43 Toolholder as boring bar shank diameter 16.00mm for receiving indexable inserts type S223 with the smallest bore diameter 22.00 mm. |
|
Paul Horn RB223.0016.1.22 Toolholder as a drill with shank diameters 16.00mm and 25.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter mm 18:00. |
|
Paul Horn RB223.0016.1.42 Toolholder as a drill with shank diameters 16.00mm and 25.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter mm 18:00. |
|
Paul Horn RB223.0016.1.43 Toolholder as a drill with shank diameters 16.00mm and 25.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter mm 18:00. |
|
Paul Horn RB223.0020.0.52 Toolholder as boring bar shank diameter 20.00 mm and overhang 0 mm for receiving indexable inserts type S223 with the smallest bore diameter 27.00 mm. |
|
Paul Horn RB223.0020.0.53 Toolholder as boring bar shank diameter 20.00 mm and overhang 0 mm for receiving indexable inserts type S223 with the smallest bore diameter 27.00 mm. |
|
Paul Horn RB223.0020.1.22 Toolholder as boring bar shank diameter 20.00 mm and 30.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter 20.00 mm. |
|
Paul Horn RB223.0020.1.52 Toolholder as boring bar shank diameter 20.00 mm and 30.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter 20.00 mm. |
|
Paul Horn RB223.0020.1.53 Toolholder as boring bar shank diameter 20.00 mm and 30.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter 20.00 mm. |
|
Paul Horn RB223.0025.0.62 Toolholder as boring bar shank diameter 25.00 mm and overhang 0 mm for receiving indexable inserts type S223 with the smallest bore diameter 33.00 mm. |
|
Paul Horn RB223.0025.0.63 Toolholder as boring bar shank diameter 25.00 mm and overhang 0 mm for receiving indexable inserts type S223 with the smallest bore diameter 33.00 mm. |
|
Paul Horn RB223.0025.1.62 Toolholder as boring bar shank diameter 25.00 mm and 50.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter 25.00 mm. |
|
Paul Horn RB223.0025.1.63 Toolholder as boring bar shank diameter 25.00 mm and 50.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter 25.00 mm. |
|
Paul Horn RB223.0025.1.K2 Basic holder as boring bar shank diameter 25.00 mm and 30.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB223.0025.2.K2 Basic holder as boring bar shank diameter 25.00 mm and 60.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB223.0032.1.K2 Basic holder as boring bar shank diameter 32.00 mm and 30.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB223.0032.2.K2 Basic holder as boring bar shank diameter 32.00 mm and 60.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB223.HM16.2.42 Toolholder as boring bar made of solid carbide with shank diameters 16.00mm and 50.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter mm 18:00. |
|
Paul Horn RB223.HM16.2.43 Toolholder as boring bar made of solid carbide with shank diameters 16.00mm and 50.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter mm 18:00. |
|
Paul Horn RB223.HM20.2.52 Toolholder as boring bar made of solid carbide with shaft diameter 20.00 mm and 60.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter 20.00 mm. |
|
Paul Horn RB223.HM20.2.53 Toolholder as boring bar made of solid carbide with shaft diameter 20.00 mm and 60.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter 20.00 mm. |
|
Paul Horn RB223.HM25.2.62 Toolholder as boring bar made of solid carbide with shaft diameter 25.00 mm and 70.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter 25.00 mm. |
|
Paul Horn RB223.HM25.2.63 Toolholder as boring bar made of solid carbide with shaft diameter 25.00 mm and 70.00 mm overhang for receiving indexable inserts type S223 with the smallest bore diameter 25.00 mm. |
|
Paul Horn RB224.0020.0.01 Toolholder as boring bar shank diameter 20.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 30.00 mm. |
|
Paul Horn RB224.0020.0.02 Toolholder as boring bar shank diameter 20.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 30.00 mm. |
|
Paul Horn RB224.0020.0.03 Toolholder as boring bar shank diameter 20.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 30.00 mm. |
|
Paul Horn RB224.0020.0.04 Toolholder as boring bar shank diameter 20.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 30.00 mm. |
|
Paul Horn RB224.0020.0.05 Toolholder as boring bar shank diameter 20.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 30.00 mm. |
|
Paul Horn RB224.0020.1.01 Toolholder as boring bar shank diameter 20.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0020.1.02 Toolholder as boring bar shank diameter 20.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0020.1.03 Toolholder as boring bar shank diameter 20.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0020.1.04 Toolholder as boring bar shank diameter 20.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0020.2.01 Toolholder as boring bar shank diameter 20.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0020.2.02 Toolholder as boring bar shank diameter 20.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0025.0.01 Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 35.00 mm. |
|
Paul Horn RB224.0025.0.02 Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 35.00 mm. |
|
Paul Horn RB224.0025.0.03 Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 35.00 mm. |
|
Paul Horn RB224.0025.0.04 Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 35.00 mm. |
|
Paul Horn RB224.0025.0.05 Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 35.00 mm. |
|
Paul Horn RB224.0025.1.01 Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0025.1.02 Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0025.1.03 Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0025.1.04 Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0025.1.05 Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0025.1.06 Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0025.1.13 Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 32.00 mm. |
|
Paul Horn RB224.0025.1.14 Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 32.00 mm. |
|
Paul Horn RB224.0025.2.01 Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0025.2.02 Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0025.2.03 Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0025.2.04 Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0032.0.03 Toolholder as boring bar shank diameter 32.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 42.00 mm. |
|
Paul Horn RB224.0032.0.04 Toolholder as boring bar shank diameter 32.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 42.00 mm. |
|
Paul Horn RB224.0032.0.05 Toolholder as boring bar shank diameter 32.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 42.00 mm. |
|
Paul Horn RB224.0032.1.03 Toolholder as boring bar shank diameter 32.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0032.1.04 Toolholder as boring bar shank diameter 32.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0032.1.13 Toolholder as boring bar shank diameter 32.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 32.00 mm. |
|
Paul Horn RB224.0032.1.14 Toolholder as boring bar shank diameter 32.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 32.00 mm. |
|
Paul Horn RB224.0032.1.15 Toolholder as boring bar shank diameter 32.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 32.00 mm. |
|
Paul Horn RB224.0032.1.16 Toolholder as boring bar shank diameter 32.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 32.00 mm. |
|
Paul Horn RB224.0032.1.K2 Basic holder as boring bar shank diameter 32.00 mm for receiving cassette type BK224, with the smallest bore diameter 40.00 mm. |
|
Paul Horn RB224.0032.2.03 Toolholder as boring bar shank diameter 32.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0032.2.04 Toolholder as boring bar shank diameter 32.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RB224.0032.2.13 Toolholder as boring bar shank diameter 32.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 32.00 mm. |
|
Paul Horn RB224.0032.2.14 Toolholder as boring bar shank diameter 32.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 32.00 mm. |
|
Paul Horn RB224.0032.2.K2 Basic holder as boring bar shank diameter 32.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 40.00 mm. |
|
Paul Horn RB224.0032.K1 Basic holder as boring bar shank diameter 32.00 mm for receiving cassette RIK / LIK224. |
|
Paul Horn RB224.0040.1.25 Toolholder as boring bar shank diameter 40.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 38.00 mm. |
|
Paul Horn RB224.0040.1.26 Toolholder as boring bar shank diameter 40.00 mm for receiving indexable inserts type S224 with the smallest bore diameter 38.00 mm. |
|
Paul Horn RB224.0040.1.K2 Basic holder as boring bar shank diameter 40.00 mm for receiving cassette type BK224, with the smallest bore diameter 40.00 mm. |
|
Paul Horn RB224.0040.2.K2 Basic holder as boring bar shank diameter 40.00 mm for receiving cassette type BK224, with the smallest bore diameter 40.00 mm. |
|
Paul Horn RB224.0040.K1 Basic holder as boring bar shank diameter 40.00 mm for receiving cassette RIK / LIK224. |
|
Paul Horn RB224.00C4.2.K2 Basic holder as boring bar with HORN polygonal shank ISO 26623 for receiving cassette type BK224, at 60.00 mm overhang. |
|
Paul Horn RB224.00C5.1K2 Basic holder as boring bar with HORN polygonal shank ISO 26623 for receiving cassette type BK224, at 50.00 mm overhang. |
|
Paul Horn RB224.00C5.2.K2 Basic holder as boring bar with HORN polygonal shank ISO 26623 for receiving cassette type BK224, at 70.00 mm overhang. |
|
Paul Horn RB224.00C6.2.K2 Basic holder as boring bar with HORN polygonal shank ISO 26623 for receiving cassette type BK224, at 78.00 mm overhang. |
|
Paul Horn RB224.4525.0.02 Toolholder as a drill with shank diameter 25 mm for the manufacture of corner undercuts in holes, only for full radius inserts type S224 with the smallest bore diameter 29 mm. |
|
Paul Horn RB224.4525.0.04 Toolholder as a drill with shank diameter 25 mm for the manufacture of corner undercuts in holes, only for full radius inserts type S224 with the smallest bore diameter 29 mm. |
|
Paul Horn RB224.4532.0.02 Toolholder as a drill with shank diameter 32 mm for the manufacture of corner undercuts in holes, only for full radius inserts type S224 with the smallest bore diameter 36 mm. |
|
Paul Horn RB224.4532.0.04 Toolholder as a drill with shank diameter 32 mm for the manufacture of corner undercuts in holes, only for full radius inserts type S224 with the smallest bore diameter 36 mm. |
|
Paul Horn RB224.4540.1.02 Toolholder as a drill with shank diameter 40 mm for the manufacture of corner undercuts in holes, only for full radius inserts type S224 with the smallest bore diameter 44 mm. |
|
Paul Horn RB224.4540.1.04 Toolholder as a drill with shank diameter 40 mm for the manufacture of corner undercuts in holes, only for full radius inserts type S224 with the smallest bore diameter 44 mm. |
|
Paul Horn RB224.6020.0.02 Toolholder as a drill with shank diameter 20 mm for the manufacture of corner undercuts in holes, only for full radius inserts type S224 with the smallest bore diameter 25 mm. |
|
Paul Horn RB224.6020.0.04 Toolholder as a drill with shank diameter 20 mm for the manufacture of corner undercuts in holes, only for full radius inserts type S224 with the smallest bore diameter 25 mm. |
|
Paul Horn RB224.6020.0.06 Toolholder as a drill with shank diameter 20 mm for the manufacture of corner undercuts in holes, only for full radius inserts type S224 with the smallest bore diameter 25 mm. |
|
Paul Horn RB224.6025.0.02 Toolholder as a drill with shank diameter 25 mm for the manufacture of corner undercuts in holes, only for full radius inserts type S224 with the smallest bore diameter 29 mm. |
|
Paul Horn RB224.6025.0.04 Toolholder as a drill with shank diameter 25 mm for the manufacture of corner undercuts in holes, only for full radius inserts type S224 with the smallest bore diameter 29 mm. |
|
Paul Horn RB224.6025.0.06 Toolholder as a drill with shank diameter 25 mm for the manufacture of corner undercuts in holes, only for full radius inserts type S224 with the smallest bore diameter of 29.5 mm. |
|
Paul Horn RB224.6032.0.02 Toolholder as a drill with shank diameter 32 mm for the manufacture of corner undercuts in holes, only for full radius inserts type S224 with the smallest bore diameter 36 mm. |
|
Paul Horn RB224.6032.0.04 Toolholder as a drill with shank diameter 32 mm for the manufacture of corner undercuts in holes, only for full radius inserts type S224 with the smallest bore diameter 36 mm. |
|
Paul Horn RB224.6032.0.06 Toolholder as a drill with shank diameter 32 mm for the manufacture of corner undercuts in holes, only for full radius inserts type S224 with the smallest bore diameter 36.5 mm. |
|
Paul Horn RB224.TS40.1.K2 Basic holder as boring bar with HORN shaft TS ISO 26622 for receiving cassette type BK224, with 48 mm overhang. |
|
Paul Horn RB224.TS40.2.K2 Basic holder as boring bar with HORN shaft TS ISO 26622 for receiving cassette type BK224, with 68 mm overhang. |
|
Paul Horn RB224.TS63.1.K2 Body type |
|
Paul Horn RB229.0040.1.K2 Basic holder as boring bar shank diameter 40.00 mm for receiving cassette type BK229, with the smallest bore diameter 50.00 mm. |
|
Paul Horn RB229.0040.2.K2 Basic holder as boring bar shank diameter 40.00 mm for receiving cassette type BK229, with the smallest bore diameter 50.00 mm. |
|
Paul Horn RB229.00C4.2.K2 Basic holder as boring bar with HORN polygonal shank ISO 26623 for receiving cassette type BK229, at 60.00 mm overhang. |
|
Paul Horn RB229.00C5.1K2 Basic holder as boring bar with HORN polygonal shank ISO 26623 for receiving cassette type BK229, at 50.00 mm overhang. |
|
Paul Horn RB229.00C5.2K2 Basic holder as boring bar with HORN polygonal shank ISO 26623 for receiving cassette type BK229, at 70.00 mm overhang. |
|
Paul Horn RB229.00C6.1.K2 Basic holder as boring bar with HORN polygonal shank ISO 26623 for receiving cassette type BK229, at 58.00 mm overhang. |
|
Paul Horn RB229.00C6.2K2 Basic holder as boring bar with HORN polygonal shank ISO 26623 for receiving cassette type BK229, at 78.00 mm overhang. |
|
Paul Horn RB229.TS40.2.K2 Basic holder as boring bar with HORN shaft TS ISO 26622 for receiving cassette type BK229, at 68.00 mm overhang. |
|
Paul Horn RB229.TS50.1.K2 Basic holder as boring bar with HORN shaft TS ISO 26622 for receiving cassette type BK229, at 54.00 mm overhang. |
|
Paul Horn RB229.TS50.2.K2 Basic holder as boring bar with HORN shaft TS ISO 26622 for receiving cassette type BK229, at 74.00 mm overhang. |
|
Paul Horn RB229.TS63.1.K2 Body type |
|
Paul Horn RB229.TS63.2.K2 Basic holder as boring bar with HORN shaft TS ISO 26622 for receiving cassette type BK229, at 82.00 mm overhang. |
|
Paul Horn RB29F.F040.15.08 Toolholder for wheel machining, matching Wendeschneiplatten type S29F, maximum cutting width 8.00 mm, minimum machining diameter is 200.00 mm. |
|
Paul Horn RB29F.F040.17.08 Toolholder for wheel machining, matching Wendeschneiplatten type S29F, maximum cutting width 8.00 mm, minimum machining diameter is 200.00 mm. |
|
Paul Horn RBA114.0016.01 Toolholder as Vollhartmetallbohrstange with shaft diameter 16 mm for receiving indexable inserts type 114 for grooving. |
|
Paul Horn RBA114.0016.02 Toolholder as Vollhartmetallbohrstange with shaft diameter 16 mm for receiving indexable inserts type 114 for grooving. |
|
Paul Horn RBK223.0028.01 Cassette for internal grooving and -längsdrehen for receiving indexable inserts type S223 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RBK223.0028.02 Cassette for internal grooving and -längsdrehen for receiving indexable inserts type S223 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RBK223.0028.03 Cassette for internal grooving and -längsdrehen for receiving indexable inserts type S223 with the smallest bore diameter 28.00 mm. |
|
Paul Horn RBK224.0040.01 Cassette for internal grooving and -längsdrehen for receiving indexable inserts type S224 with the smallest bore diameter 40.00 mm. |
|
Paul Horn RBK224.0040.02 Cassette for internal grooving and -längsdrehen for receiving indexable inserts type S224 with the smallest bore diameter 40.00 mm. |
|
Paul Horn RBK224.0040.03 Cassette for internal grooving and -längsdrehen for receiving indexable inserts type S224 with the smallest bore diameter 40.00 mm. |
|
Paul Horn RBK224.0040.04 Cassette for internal grooving and -längsdrehen for receiving indexable inserts type S224 with the smallest bore diameter 40.00 mm. |
|
Paul Horn RBK224.0040.05 Cassette for internal grooving and -längsdrehen for receiving indexable inserts type S224 with the smallest bore diameter 40.00 mm. |
|
Paul Horn RBK224.0040.06 Cassette for internal grooving and -längsdrehen for receiving indexable inserts type S224 with the smallest bore diameter 40.00 mm. |
|
Paul Horn RBK229.0050.03 Cassette for internal grooving and -längsdrehen for receiving indexable inserts type S229, with the smallest bore diameter 50.00 mm. |
|
Paul Horn RBK229.0050.04 Cassette for internal grooving and -längsdrehen for receiving indexable inserts type S229, with the smallest bore diameter 50.00 mm. |
|
Paul Horn RBK229.0050.05 Cassette for internal grooving and -längsdrehen for receiving indexable inserts type S229, with the smallest bore diameter 50.00 mm. |
|
Paul Horn RBM.3225.040 Reduction of URMA Beta Module 42 to 25, length 40 mm. |
|
Paul Horn RBM.4032.045 Reduction of URMA Beta Module 42 to 32. Length 45 mm. |
|
Paul Horn RBM.5040.050 Reduction of URMA Beta Module 50 to 42. Length 50 mm. |
|
Paul Horn RBM.6325.045 Reduction of URMA Beta Module 63 to 25, length 45 mm. |
|
Paul Horn RBM.6332.050 Reduction of URMA Beta Module 63 to 32. Length 50 mm. |
|
Paul Horn RBM.6340.055 Reduction of URMA Beta Module 63 to 42. Length 55 mm. |
|
Paul Horn RCGT0602M0.F.HN PD70 Insert PCD-tipped, round, for machining non-ferrous metals and carbon fiber materials, diameter 6 mm. |
|
Paul Horn RCGT0602M0.F.HS PD70 Insert PCD-tipped, round, for machining non-ferrous metals and carbon fiber materials, diameter 6 mm. |
|
Paul Horn RCGT0803M0.F.HN PD70 Insert PCD-tipped, round, for machining non-ferrous metals and carbon fiber materials, diameter 8 mm. |
|
Paul Horn RCGT0803M0.F.HS PD70 Insert PCD-tipped, round, for machining non-ferrous metals and carbon fiber materials, diameter 8 mm. |
|
Paul Horn RCGT1003M0.F.HN PD70 Insert PCD-tipped, round, for machining non-ferrous metals and carbon fiber materials, diameter 10 mm. |
|
Paul Horn RCGT1003M0.F.HS PD70 Insert PCD-tipped, round, for machining non-ferrous metals and carbon fiber materials, diameter 10 mm. |
|
Paul Horn RCGT10T3M0.F.HN PD70 Insert PCD-tipped, round, for machining non-ferrous metals and carbon fiber materials, diameter 10 mm. |
|
Paul Horn RCGT10T3M0.F.HS PD70 Insert PCD-tipped, round, for machining non-ferrous metals and carbon fiber materials, diameter 10 mm. |
|
Paul Horn RCGT1204M0.F.HN PD70 Insert PCD-tipped, round, for machining non-ferrous metals and carbon fiber materials, diameter 12 mm. |
|
Paul Horn RCGT1204M0.F.HS PD70 Insert PCD-tipped, round, for machining non-ferrous metals and carbon fiber materials, diameter 12 mm. |
|
Paul Horn RCGW0602M0.F.H0 PD70 Insert PCD-tipped, round, for machining non-ferrous metals and carbon fiber materials, diameter 6 mm. |
|
Paul Horn RCGW0803M0.F.H0 PD70 Insert PCD-tipped, round, for machining non-ferrous metals and carbon fiber materials, diameter 8 mm. |
|
Paul Horn RCGW1003M0.F.H0 PD70 Insert PCD-tipped, round, for machining non-ferrous metals and carbon fiber materials, diameter 10 mm. |
|
Paul Horn RCGW10T3M0.F.H0 PD70 Insert PCD-tipped, round, for machining non-ferrous metals and carbon fiber materials, diameter 10 mm. |
|
Paul Horn RCGW1204M0.F.H0 PD70 Insert PCD-tipped, round, for machining non-ferrous metals and carbon fiber materials, diameter 12 mm. |
|
Paul Horn RDAH.2525.62 Tool holders with shank 25.00 mm wide x 25.00 mm height for high feed turning, matching indexable insert type DAH62 .., execution law. |
|
Paul Horn RH100.1010.01 Toolholder with shaft 10:00 mm width x height mm 10:00 for grooving and parting, maximum groove depth 10:50 mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1010.11 Toolholder with shaft 10:00 mm width x height mm 10:00 for grooving and parting, maximum groove depth 13:00 mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1212.01 Tool holders with shank 12.00 mm Width x 12.00 mm height for grooving and parting, maximum groove depth 13:00 mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1212.01.IK Tool holders with shank 12.00 mm Width x 12.00 mm height for grooving and parting, maximum groove depth 13:00 mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1212.02 Tool holders with shank 12.00 mm Width x 12.00 mm height for grooving and parting, maximum groove depth 13:00 mm, groove width 2:50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1212.02.IK Tool holders with shank 12.00 mm Width x 12.00 mm height for grooving and parting, maximum groove depth 13:00 mm, groove width 2:50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1212.03 Tool holders with shank 12.00 mm Width x 12.00 mm height for grooving and parting, maximum groove depth 13:00 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.1212.03.IK Tool holders with shank 12.00 mm Width x 12.00 mm height for grooving and parting, maximum groove depth 13:00 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.1212.11 Tool holders with shank 12.00 mm Width x 12.00 mm height for grooving and parting, maximum groove depth 16.00mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1212.11.IK Tool holders with shank 12.00 mm Width x 12.00 mm height for grooving and parting, maximum groove depth 16.00mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1212.12 Tool holders with shank 12.00 mm wide x 12.00 mm height for grooving and parting, maximum groove depth 16.00 mm, groove width 2.50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1212.12.IK Tool holders with shank 12.00 mm Width x 12.00 mm height for grooving and parting, maximum groove depth 16.00mm, groove width 2:50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1212.24.61 Tool holders with shank 12.00 mm wide x 12.00 mm height for grooving and parting, maximum groove depth 13.00 mm, groove width 2.00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1212.32.63 Tool holders with shank 12.00 mm Width x 12.00 mm height for grooving and parting, maximum groove depth 17.00 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.0.23.IK Toolholder with shank 20 mm width x 16 mm height for grooving and parting, maximum groove depth 21.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.0.24.IK Toolholder with shank 20 mm width x 16 mm height for grooving and parting, maximum groove depth 21.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.02 Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 10:50 mm, groove width 2:50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.02.IK Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 10:50 mm, groove width 2:50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.03 Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 10:50 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.03.IK Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 10:50 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.1.23.IK Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 21.5 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.11 Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 16.00mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.11.IK Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 16.00mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.12 Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 16.00mm, groove width 2:50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.12.IK Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 16.00mm, groove width 2:50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.13 Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 16.00mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.13.IK Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 16.00mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.2.23.IK Toolholder with shank 16 mm width x 16 mm height for grooving and parting, maximum groove depth 21.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.2.24.IK Toolholder with shank 16 mm width x 16 mm height for grooving and parting, maximum groove depth 21.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.21 Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 21:00 mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.21.IK Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 21:00 mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.22 Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 21:00 mm, groove width 2:50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.22.IK Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 21:00 mm, groove width 2:50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.23 Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 21:00 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.23.IK Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 21:00 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.24.61 Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 13:00 mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.1616.3.22.IK Toolholder with shank 16 mm width x 16 mm height for grooving and parting, maximum groove depth 21.5 mm, groove width 2.5 mm, matching insert type S100, execution law. |
|
Paul Horn RH100.1616.32.63 Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 17.00 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.1703.21 Toolholder as Abstechschwert with stem 20.3 mm width x height mm 17:40 parting, maximum groove depth 17:50 mm, groove width 2:00 mm, self-locking, matching insert type S100, execution law. |
|
Paul Horn RH100.1703.33 Toolholder as Abstechschwert with stem 20.3 mm width x height mm 17:40 parting, maximum groove depth 30.00 mm, groove width 3.00mm, self-locking, matching insert type S100, execution law. |
|
Paul Horn RH100.2020.0.23.IK Toolholder with shank 20 mm width x 20 mm height for grooving and parting, maximum groove depth 21.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.0.24.IK Toolholder with shank 20 mm width x 20 mm height for grooving and parting, maximum groove depth 21.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.0.73.IK Toolholder with shank 20 mm width x 20 mm height for grooving and parting, maximum groove depth of 25.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.0.74.IK Toolholder with shank 20 mm width x 20 mm height for grooving and parting, maximum groove depth of 25.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.1.13.IK Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 16.00mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.1.23.IK Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 21.5 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.1.33.IK Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 33 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.1.34.IK Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 33 mm, groove width 4:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.11 Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 16.00mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.11.IK Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 16.00mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.12 Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 16.00mm, groove width 2:50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.12.IK Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 16.00mm, groove width 2:50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.13 Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 16.00mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.13.IK Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 16.00mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.14 Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 16.00mm, groove width 4:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.15 Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 16.00mm, groove width 5:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.2.23.IK Toolholder with shank 20 mm width x 20 mm height for grooving and parting, maximum groove depth 21.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.2.24.IK Toolholder with shank 20 mm width x 20 mm height for grooving and parting, maximum groove depth 21.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.2.73.IK Toolholder with shank 20 mm width x 20 mm height for grooving and parting, maximum groove depth of 25.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.2.74.IK Toolholder with shank 20 mm width x 20 mm height for grooving and parting, maximum groove depth of 25.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.21 Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 21:00 mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.21.IK Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 21:00 mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.22 Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 21:00 mm, groove width 2:50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.22.IK Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 21:00 mm, groove width 2:50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.23 Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 21:00 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.23.IK Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 21:00 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.3.0.04.IK Toolholder with shank 20 mm width x 20 mm height for grooving and parting, maximum groove depth 33 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.3.04 Toolholder with shank 20 mm width x 20 mm height for grooving and parting, maximum groove depth 33.00 mm, slot width 4 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.3.05 Toolholder with shank 20 mm width x 20 mm height for grooving and parting, maximum groove depth 33.00 mm, groove width 5 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.3.2.04.IK Toolholder with shank 20 mm width x 20 mm height for grooving and parting, maximum groove depth 33 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.3.22.IK Toolholder with shank 20 mm width x 20 mm height for grooving and parting, maximum groove depth 21.5 mm, groove width 2.5 mm, matching insert type S100, execution law. |
|
Paul Horn RH100.2020.3.33.IK Toolholder with shank 20 mm width x 20 mm height for grooving and parting, maximum groove depth 33 mm, groove width 3 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.32 Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 32.50 mm, groove width 2:50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.33 Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 32.50 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.33.IK Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 32.50 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.34 Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 32.50 mm, groove width 4:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.35 Tool holders with shank 20.00 mm wide x 20.00 mm height for grooving and parting, maximum groove depth 32.50 mm, groove width 5.00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.73 Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 25.00 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2020.74 Tool holders with shank 20.00 mm Width x 20.00 mm height for grooving and parting, maximum groove depth 25.00 mm, groove width 4:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2203.33 Toolholder as Abstechschwert with stem 20.3 mm width x 22.10mm height parting, maximum groove depth 38.00 mm, groove width 3.00mm, matching insert type S100, execution law. |
|
Paul Horn RH100.2525.0.23.IK Toolholder with shank 25 mm width x 25 mm height for grooving and parting, maximum groove depth 21.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.0.24.IK Toolholder with shank 25 mm width x 25 mm height for grooving and parting, maximum groove depth 21.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.0.73.IK Toolholder with shank 25 mm width x 25 mm height for grooving and parting, maximum groove depth of 25.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.0.74.IK Toolholder with shank 25 mm width x 25 mm height for grooving and parting, maximum groove depth of 25.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.1.33.IK Tool holders with shank 25.00 mm wide x 25.00 mm height for grooving and parting, maximum groove depth 33 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.1.34.IK Tool holders with shank 25.00 mm wide x 25.00 mm height for grooving and parting, maximum groove depth 41 mm, groove width 4:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.13 Tool holders with shank 25.00 mm wide x 25.00 mm height for grooving and parting, maximum groove depth 16.00mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.13.IK Tool holders with shank 25.00 mm wide x 25.00 mm height for grooving and parting, maximum groove depth 16.00mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.14 Tool holders with shank 25.00 mm wide x 25.00 mm height for grooving and parting, maximum groove depth 16.00mm, groove width 4:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.2.23.IK Toolholder with shank 25 mm width x 25 mm height for grooving and parting, maximum groove depth 21.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.2.24.IK Toolholder with shank 25 mm width x 25 mm height for grooving and parting, maximum groove depth 21.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.2.73.IK Toolholder with shank 25 mm width x 25 mm height for grooving and parting, maximum groove depth of 25.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.2.74.IK Toolholder with shank 25 mm width x 25 mm height for grooving and parting, maximum groove depth of 25.5 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.21 Tool holders with shank 25.00 mm wide x 25.00 mm height for grooving and parting, maximum groove depth 21:00 mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.21.IK Tool holders with shank 25.00 mm wide x 25.00 mm height for grooving and parting, maximum groove depth 21:00 mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.22 Tool holders with shank 25.00 mm wide x 25.00 mm height for grooving and parting, maximum groove depth 21:00 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.22.IK Tool holders with shank 25.00 mm wide x 25.00 mm height for grooving and parting, maximum groove depth 21:00 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.23 Tool holders type |
|
Paul Horn RH100.2525.23.IK Tool holders type |
|
Paul Horn RH100.2525.3.0.04.IK Toolholder with shank 25 mm width x 25 mm height for grooving and parting, maximum groove depth 33 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.3.06 Tool holders with shank 25.00 mm wide x 25.00 mm height for grooving and parting, maximum groove depth 33.00 mm, groove width 6:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.3.2.04.IK Toolholder with shank 25 mm width x 25 mm height for grooving and parting, maximum groove depth 33 mm, groove width 0 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.3.33.IK Toolholder with shank 25 mm width x 25 mm height for grooving and parting, maximum groove depth 33 mm, groove width 3 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.33 Tool holders with shank 25.00 mm wide x 25.00 mm height for grooving and parting, maximum groove depth 32.50 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.33.IK Tool holders with shank 25.00 mm wide x 25.00 mm height for grooving and parting, maximum groove depth 32.50 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.34 Tool holders with shank 25.00 mm wide x 25.00 mm height for grooving and parting, maximum groove depth 40.50 mm, groove width 4:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.35 Tool holders with shank 25.00 mm wide x 25.00 mm height for grooving and parting, maximum groove depth 40.50 mm, groove width 5:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2525.73 Tool holders with shank 25.00 mm wide x 25.00 mm height for grooving and parting, maximum groove depth 25.00 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2608.31 Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 26.00 mm height for parting, maximum groove depth 21:00 mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2608.31R Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 26.00 mm height for parting, maximum groove depth 21.00 mm, groove width 2.00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2608.33 Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 26.00 mm height for parting, maximum groove depth 25.00 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2608.33R Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 26.00 mm height for parting, maximum groove depth 25.00 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2608.34 Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 26.00 mm height for parting, maximum groove depth 25.00 mm, groove width 4.00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2608.71 Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 26.00 mm height for parting, maximum groove depth 25.00 mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2608.71R Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 26.00 mm height for parting, maximum groove depth 25.00 mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.2608.93 Toolholder as reinforced Abstechschwert with shank 8:00 mm wide x 26.00 mm height for parting, maximum groove depth 25.00 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.2608.93R Toolholder as reinforced Abstechschwert with shank 8:00 mm wide x 26.00 mm height for parting, maximum groove depth 25.00 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.2.44 Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 32.00 mm height for parting, maximum groove depth 41.00 mm, groove width 4:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.31 Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 32.00 mm height for parting, maximum groove depth 25.00 mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.32 Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 32.00 mm height for parting, maximum groove depth 34 mm, groove width 2:50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.33 Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 32.00 mm height for parting, maximum groove depth 34 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.33R Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 32.00 mm height for parting, maximum groove depth 34 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.34 Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 32.00 mm height for parting, maximum groove depth 34 mm, groove width 4:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.34R Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 32.00 mm height for parting, maximum groove depth 34 mm, groove width 4:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.44 Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 32.00 mm height for parting, maximum groove depth 41.00 mm, groove width 4:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.71 Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 32.00 mm height for parting, maximum groove depth 25.00 mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.71R Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 32.00 mm height for parting, maximum groove depth 25.00 mm, groove width 2:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.72 Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 32.00 mm height for parting, maximum groove depth 25.00 mm, groove width 2:50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.72R Toolholder as reinforced Abstechschwert with shank 7.90 mm wide x 32.00 mm height for parting, maximum groove depth 25.00 mm, groove width 2:50 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.83 Toolholder as reinforced Abstechschwert with shank 8 mm wide x 32.00 mm height for parting, maximum groove depth 33.50 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.83N Tool holders type |
|
Paul Horn RH100.3208.83R Toolholder as reinforced Abstechschwert with shank 8 mm wide x 32.00 mm height for parting, maximum groove depth 33.50 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.84 Toolholder as reinforced Abstechschwert with shank 8 mm wide x 32.00 mm height for parting, maximum groove depth 33.50 mm, groove width 4.00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.84N Toolholder as reinforced Abstechschwert with shank 8 mm wide x 32.00 mm height for parting, maximum groove depth 41 mm, groove width 4:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.84R Toolholder as reinforced Abstechschwert with shank 8 mm wide x 32.00 mm height for parting, maximum groove depth 33.50 mm, groove width 4:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.93 Toolholder as reinforced Abstechschwert with shank 8:00 mm wide x 32.00 mm height for parting, maximum groove depth 32.50 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.3208.93R Toolholder as reinforced Abstechschwert with shank 8:00 mm wide x 32.00 mm height for parting, maximum groove depth 32.50 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.3225.3.06 Tool holders with shank 25.00 mm wide x 32.00 mm height for grooving and parting, maximum groove depth 33.00 mm, groove width 6:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3225.3.08 Tool holders with shank 25.00 mm wide x 32.00 mm height for grooving and parting, maximum groove depth 33.00 mm, groove width 8:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3225.38 Tool holders with shank 25.00 mm wide x 32.00 mm height for grooving and parting, maximum groove depth 35.00 mm, groove width 8:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3225.4.08 Tool holders with shank 25.00 mm wide x 32.00 mm height for grooving and parting, maximum groove depth 41 mm, groove width 8:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3225.4.10 Tool holders with shank 25.00 mm wide x 32.00 mm height for grooving and parting, maximum groove depth 41.00 mm, groove width 10:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100.3225.4.12 Tool holders with shank 25.00 mm wide x 32.00 mm height for grooving and parting, maximum groove depth 41.00 mm, 12.00 mm groove width matching insert type S100, execution law. |
|
Paul Horn RH100.3280.73R Toolholder with shank 7.90 mm wide x 32.00 mm height for grooving and parting, maximum groove depth 32.5 mm, groove width 3.00mm matching insert type S100, execution law. |
|
Paul Horn RH100.3280.74R Toolholder with shank 7.90 mm wide x 32.00 mm height for grooving and parting, maximum groove depth 32.5 mm, groove width 4:00 mm matching insert type S100, execution law. |
|
Paul Horn RH100260872R Tool holders type RH100.2608.72R |
|
Paul Horn RH101.1010.1.16 Toolholder with shaft 10:00 mm width x height mm 10:00 for grooving and parting, maximum groove depth 13 mm, groove width 2:00 mm matching insert type S101 |
|
Paul Horn RH101.1212.1.16 Tool holders with shank 12.00 mm Width x 12.00 mm height for grooving and parting, maximum groove depth 13 mm, groove width 2:00 mm matching insert type S101 |
|
Paul Horn RH101.1616.1.16 Tool holders with shank 16.00mm width x 16.00mm height for grooving and parting, maximum groove depth 13 mm, groove width 2:00 mm matching insert type S101 |
|
Paul Horn RH105.0808.01 Tool holders with shank 8:00 mm wide x 8.00 mm Max height for receiving inserts Type 105, Type law. |
|
Paul Horn RH105.1010.01 Toolholder with shaft 10:00 mm width x height mm 10:00 for receiving inserts Type 105, Type law. |
|
Paul Horn RH105.1212.01 Tool holders with shank 12.00 mm Width x 12.00 mm height for receiving inserts Type 105, Type law. |
|
Paul Horn RH105.1616.01 Tool holders with shank 16.00mm width x 16.00mm height for receiving inserts Type 105, Type law. |
|
Paul Horn RH114.WF20.02 Tool holders with interface WF20-12 monoblock for receiving inserts Type 114, Type law. |
|
Paul Horn RH114.WF24.02 Tool holders type |
|
Paul Horn RH114.WF32.02 Tool holders type |
|
Paul Horn RH117.MD10.45.5.10 Toolholder with shank 11 mm width x 10 mm height for receiving equipped with monocrystalline diamond inserts type 117 for mirror turning, execution law. |
|
Paul Horn RH117.MD10.90.5.10 Toolholder with shank 10 mm width x 10 mm height for receiving equipped with monocrystalline diamond inserts type 117 for mirror turning, execution law. |
|
Paul Horn RH223.1010.01 Toolholder with shaft 10:00 mm width x height mm 10:00 to Einstechen- and longitudinal turning, maximum groove depth 8:00 mm, groove width 2:00 mm matching insert type S223, execution law. |
|
Paul Horn RH223.1010.02 Toolholder with shaft 10:00 mm width x height mm 10:00 to Einstechen- and longitudinal turning, maximum groove depth 8:00 mm, groove width 2:50 mm matching insert type S223, execution law. |
