|
Paul Horn S224.0500.58 AS62 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.8 mm and maximum groove depth of 18 mm, geometry 5, matching clamp holder z. B. H224. |
|
Paul Horn S224.0500.58 AS66 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.8 mm and maximum groove depth of 18 mm, geometry 5, matching clamp holder z. B. H224. |
|
Paul Horn S224.0500.58 TC92 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.8 mm and maximum groove depth of 18 mm, geometry 5, matching clamp holder z. B. H224. |
|
Paul Horn S224.0500.58 TI25 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0500.A4 AS62 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0500.A4 TC92 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 18 mm, Geometry A, suitable for clamping holder. B. H224. |
|
Paul Horn S224.0500.A4 TF45 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0500.A4 TI22 Indexable insert S224.0500.A4 Ti22 for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 18 mm, Geometry A, suitable for clamping holder. B. H224. |
|
Paul Horn S224.0500.A4 TI25 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 18 mm, Geometry A, suitable for clamping holder. B. H224. |
|
Paul Horn S224.0500.A4 TN32 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 18 mm, Geometry A, suitable for clamping holder. B. H224. |
|
Paul Horn S224.0500.A4 TN35 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0500.A8 AS62 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0500.A8 TN32 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.8 mm and maximum groove depth of 18 mm, Geometry A, suitable for clamping holder. B. H224. |
|
Paul Horn S224.0500.H6 AL96 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 18 mm depth. |
|
Paul Horn S224.0500.H6 TF42 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.6 mm and maximum groove depth of 18 mm, Geometry H, suitable for clamping holder. B. H224. |
|
Paul Horn S224.0500.H8 AL96 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 18 mm depth. |
|
Paul Horn S224.0500.H8 TF42 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.8 mm and maximum groove depth of 18 mm, Geometry H, suitable for clamping holder. B. H224. |
|
Paul Horn S224.0500.L4 AL96 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0500.L4 AS62 Indexable insert for grooving and turning with a cutting width of 5 mm and maximum groove depth of 18 mm, suitable for clamping holder. B. H224. |
|
Paul Horn S224.0500.L4 TF42 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0500.L4 TI22 Indexable insert S224.0500.L4 Ti22 for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 18 mm, L geometry, suitable for clamping holder. B. H224. |
|
Paul Horn S224.0500.L6 AL96 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0500.L6 AS62 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0500.L6 TF42 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0500.L6 TI22 Indexable insert S224.0500.L6 Ti22 for grooving and turning with a cutting width of 5 mm, corner radius 0.6 mm and maximum groove depth of 18 mm, L geometry, suitable for clamping holder. B. H224. |
|
Paul Horn S224.0600.34 AS62 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0600.34 AS66 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 18 mm, geometry 3, matching clamp holder for. B. H224. |
|
Paul Horn S224.0600.34 TF45 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 18 mm, geometry 3, matching clamp holder for. B. H224. |
|
Paul Horn S224.0600.34 TI25 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0600.34 TN32 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 18 mm, geometry 3, matching clamp holder for. B. H224. |
|
Paul Horn S224.0600.34 TN35 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 18 mm, geometry 3, matching clamp holder for. B. H224. |
|
Paul Horn S224.0600.38 AS62 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0600.38 AS66 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.8 mm and maximum groove depth of 18 mm, geometry 3, matching clamp holder for. B. H224. |
|
Paul Horn S224.0600.38 TF45 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.8 mm and maximum groove depth of 18 mm, geometry 3, matching clamp holder for. B. H224. |
|
Paul Horn S224.0600.38 TN32 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0600.38 TN35 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.8 mm and maximum groove depth of 18 mm, geometry 3, matching clamp holder for. B. H224. |
|
Paul Horn S224.0600.54 AS62 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0600.54 AS66 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 18 mm, geometry 5, matching clamp holder z. B. H224. |
|
Paul Horn S224.0600.54 TC92 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0600.54 TF45 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 18 mm, geometry 5, matching clamp holder z. B. H224. |
|
Paul Horn S224.0600.54 TI25 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 18 mm, geometry 5, matching clamp holder z. B. H224. |
|
Paul Horn S224.0600.54 TN35 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 18 mm, geometry 5, matching clamp holder z. B. H224. |
|
Paul Horn S224.0600.58 AS62 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0600.58 AS66 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.8 mm and maximum groove depth of 18 mm, geometry 5, matching clamp holder z. B. H224. |
|
Paul Horn S224.0600.A4 AS62 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0600.A4 TI25 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 18 mm, Geometry A, suitable for clamping holder. B. H224. |
|
Paul Horn S224.0600.A4 TN32 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 18 mm, Geometry A, suitable for clamping holder. B. H224. |
|
Paul Horn S224.0600.A4 TN35 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0600.A8 AS62 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0600.A8 TN35 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0600.H6 AL96 The indexable insert with a cutting width of 6 mm is suitable for penetration of inner and outer contours with up to 18 mm depth. |
|
Paul Horn S224.0600.H6 TF42 The indexable insert with a cutting width of 6 mm is suitable for penetration of inner and outer contours with up to 18 mm depth. |
|
Paul Horn S224.0600.H8 AL96 The indexable insert with a cutting width of 6 mm is suitable for penetration of inner and outer contours with up to 18 mm depth. |
|
Paul Horn S224.0600.H8 TF42 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.8 mm and maximum groove depth of 18 mm, Geometry H, suitable for clamping holder. B. H224. |
|
Paul Horn S224.0600.L4 AL96 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0600.L4 AS62 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0600.L4 TF42 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0600.L4 TI22 Indexable insert S224.0600.L4 Ti22 for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 18 mm, L geometry, suitable for clamping holder. B. H224. |
|
Paul Horn S224.0600.L6 AL96 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.0600.L6 AS62 Indexable insert for grooving and turning with a cutting width of 6 mm and a maximum groove depth of 18 mm, suitable for clamping holder. B. H224. |
|
Paul Horn S224.0600.L6 TF42 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.6 mm and maximum groove depth of 18 mm, L geometry, suitable for clamping holder. B. H224. |
|
Paul Horn S224.0600.L6 TI22 The indexable insert S224.0600.L6 Ti22 with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.NC25.D2 TI22 The indexable insert S224.NC25.D2 Ti22 with a cutting width of 2.5 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.NC25.D2 TI25 The indexable insert with a cutting width of 2.5 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.NC25.D2 TI26 Indexable insert for grooving and turning with a cutting width of 2.5 mm, corner radius 0.2 mm and maximum groove depth of 18 mm, D geometry, suitable for clamping holder. B. H224. |
|
Paul Horn S224.NC30.D2 TI22 The indexable insert S224.NC30.D2 Ti22 with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S224.NC30.D2 TI25 Indexable insert B. H224 for grooving and turning with a cutting width of 3 mm, corner radius 0.2 mm and maximum groove depth of 18 mm, D geometry, suitable for clamping holder.. |
|
Paul Horn S224.NC30.D2 TI26 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 18 mm depth. |
|
Paul Horn S229.0015.K3 AS62 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0015.K3 AS66 Indexable insert for grooving and turning with a cutting width of 3 mm, full radius 1.5 mm and maximum groove depth of 25 mm, geometry K, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0015.KF3 AS66 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0020.K4 AS62 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0020.K4 AS66 Indexable insert for grooving and turning with a cutting width of 4 mm, full radius 2 mm and maximum groove depth of 25 mm, geometry K, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0020.KF4 AS66 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0025.K5 AS62 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0025.K5 AS66 Indexable insert for grooving and turning with a cutting width of 5 mm, full radius 2.5 mm and maximum groove depth of 25 mm, geometry K, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0025.KF5 AS66 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0030.C0 TF45 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn S229.0030.C0 TI25 Indexable insert for grooving and turning with a cutting width of 3 mm and a maximum groove depth of 25 mm, geometry C, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0030.C0 TN35 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn S229.0030.C1 TF45 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn S229.0030.C1 TI25 The indexable insert with a cutting width of 3 mm is suitable for parting and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0030.C1 TN35 Indexable insert for grooving and turning with a cutting width of 3 mm and a maximum groove depth of 25 mm, geometry C, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0030.K6 AS62 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0030.K6 AS66 Indexable insert for grooving and turning with a cutting width of 6 mm, full radius 3 mm and maximum groove depth of 25 mm, geometry K, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0030.KF6 AS66 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0040.C0 TI25 The indexable insert with a cutting width of 4 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn S229.0040.C0 TN35 Indexable insert for grooving and turning with a cutting width of 4 mm and a maximum groove depth of 25 mm, geometry C, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0040.C1 TF45 The indexable insert with a cutting width of 4 mm is suitable for parting and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0040.C1 TI25 Indexable insert for grooving and turning with a cutting width of 4 mm and a maximum groove depth of 25 mm, geometry C, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0040.K8 AS62 The indexable insert with a cutting width of 8 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.32 AL96 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.32 AS62 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.32 AS66 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.32 H54 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.32 MG12 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.32 TC92 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.32 TF45 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.32 TI22 The indexable insert S229.0300.32 Ti22 with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.32 TI25 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.32 TN32 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.32 TN35 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.34 AL96 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.34 AS66 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0300.34 H54 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0300.34 TC92 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0300.34 TF45 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.34 TI22 Indexable insert S229.0300.34 Ti22 for grooving and turning with a cutting width of 3 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0300.34 TI25 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0300.34 TN32 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0300.34 TN35 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.52 AS62 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.52 TC92 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0300.52 TF45 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.52 TI22 The indexable insert S229.0300.52 Ti22 with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.52 TI25 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.52 TN32 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.52 TN35 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0300.54 AS62 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.54 TC92 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.54 TI22 Indexable insert S229.0300.54 Ti22 for grooving and turning with a cutting width of 3 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0300.54 TI25 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0300.54 TN32 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0300.A2 AS62 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.A2 TC92 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0300.A2 TF45 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.A2 TI22 Indexable insert S229.0300.A2 Ti22 for grooving and turning with a cutting width of 3 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0300.A2 TI25 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0300.A2 TN32 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0300.A2 TN35 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0300.A4 AS62 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0300.A4 TF45 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0300.A4 TI25 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0300.A4 TN32 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0300.A4 TN35 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0300.E2 AS62 The indexable insert with a cutting width of 3 mm is suitable for parting and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0300.E2 TC92 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, geometry E, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0300.E2 TF45 The indexable insert with a cutting width of 3 mm is suitable for parting and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0300.E2 TF46 The indexable insert with a cutting width of 3 mm is suitable for parting and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0300.E2 TI25 The indexable insert with a cutting width of 3 mm is suitable for parting and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0300.E4 AS62 The indexable insert with a cutting width of 3 mm is suitable for parting and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0300.E4 TF45 The indexable insert with a cutting width of 3 mm is suitable for parting and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0300.F2 TF43 The indexable insert with a cutting width of 3 mm is suitable for parting and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0300.F2 TF45 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, geometry F, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0300.F2 TF46 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, geometry F, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0300.F2 TI22 The indexable insert S229.0300.F2 Ti22 with a cutting width of 3 mm is suitable for parting and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0300.F4 TF45 The indexable insert with a cutting width of 3 mm is suitable for parting and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0300.FY2 TI25 The indexable insert with a cutting width of 3 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0300.H4 AL96 The indexable insert with a cutting width of 3 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0300.H4 TF42 Indexable insert for grooving and turning with a cutting width of 3 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry H, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0300.H6 AL96 The indexable insert with a cutting width of 3 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0300.H6 TF42 The indexable insert with a cutting width of 3 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0300.HR4 AS62 The indexable insert with a cutting width of 3 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0300.N2.G AS45 The indexable insert with a cutting width of 3 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0300.N4.G AS45 The indexable insert with a cutting width of 3 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.32 AL96 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.32 AS62 Indexable insert for grooving and turning with a cutting width of 4 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0400.32 AS66 Indexable insert for grooving and turning with a cutting width of 4 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0400.32 H54 Indexable insert for grooving and turning with a cutting width of 4 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0400.32 TC92 The indexable insert with a cutting width of 4 mm is suitable for grooving, turning and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.32 TF45 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.32 TI22 Indexable insert S229.0400.32 Ti22 for grooving and turning with a cutting width of 4 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0400.32 TI25 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.32 TN32 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.32 TN35 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.34 AL96 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.34 AS62 Indexable insert for grooving and turning with a cutting width of 4 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0400.34 AS66 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.34 H54 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.34 TC92 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.34 TF42 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.34 TF45 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.34 TI25 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.34 TN32 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.34 TN35 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.52 AS62 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.52 TC92 The indexable insert with a cutting width of 4 mm is suitable for grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.52 TI25 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.52 TN35 The indexable insert with a cutting width of 4 mm is suitable for grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.54 AS62 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.54 TF45 The indexable insert with a cutting width of 4 mm is suitable for grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.54 TI22 Indexable insert S229.0400.54 Ti22 for grooving and turning with a cutting width of 4 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0400.54 TI25 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.54 TN32 Indexable insert for grooving and turning with a cutting width of 4 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0400.54 TN35 The indexable insert with a cutting width of 4 mm is suitable for grooving, turning and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.A2 AS62 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.A2 TC92 The indexable insert with a cutting width of 4 mm is suitable for grooving, turning and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.A2 TF45 Indexable insert for grooving and turning with a cutting width of 4 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0400.A2 TI22 Indexable insert S229.0400.A2 Ti22 for grooving and turning with a cutting width of 4 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0400.A2 TI25 Indexable insert for grooving and turning with a cutting width of 4 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0400.A2 TN32 The indexable insert with a cutting width of 4 mm is suitable for grooving, turning and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.A2 TN35 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.A4 AS62 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.A4 TC92 The indexable insert with a cutting width of 4 mm is suitable for grooving, turning and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.A4 TF42 Indexable insert for grooving and turning with a cutting width of 4 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0400.A4 TI22 Indexable insert S229.0400.A4 Ti22 for grooving and turning with a cutting width of 4 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0400.A4 TI25 The indexable insert with a cutting width of 4 mm is suitable for grooving, turning and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.A4 TN32 Indexable insert for grooving and turning with a cutting width of 4 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0400.A4 TN35 Indexable insert for grooving and turning with a cutting width of 4 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0400.E2 AS62 The indexable insert with a cutting width of 4 mm is suitable for parting and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.E2 TF45 The indexable insert with a cutting width of 4 mm is suitable for parting and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.E2 TI25 The indexable insert with a cutting width of 4 mm is suitable for parting and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.E4 AS62 The indexable insert with a cutting width of 4 mm is suitable for parting and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.E4 TF45 The indexable insert with a cutting width of 4 mm is suitable for parting and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.F2 TF45 Indexable insert for grooving and turning with a cutting width of 4 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, geometry F, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0400.F2 TF46 Indexable insert for grooving and turning with a cutting width of 4 mm, corner radius 0.2 mm and maximum groove depth of 25 mm, geometry F, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0400.F4 TF45 The indexable insert with a cutting width of 4 mm is suitable for parting and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.FY3 TI25 The indexable insert with a cutting width of 4 mm is suitable for parting, grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.H4 AL96 The indexable insert with a cutting width of 4 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.H4 TF42 Indexable insert for grooving and turning with a cutting width of 4 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry H, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0400.H6 AL96 The indexable insert with a cutting width of 4 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.H6 TF42 The indexable insert with a cutting width of 4 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.H8 AL96 The indexable insert with a cutting width of 4 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.H8 TF42 The indexable insert with a cutting width of 4 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.HR4 Indexable insert for grooving and turning with a cutting width of 4 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry HR, matching clamp holder for. B. H210. |
|
Paul Horn S229.0400.HR4 AS62 The indexable insert with a cutting width of 4 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.L4 AL96 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.L4 AS62 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.L4 AS66 The indexable insert with a cutting width of 4 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0400.L4 TF42 Indexable insert for grooving and turning with a cutting width of 4 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, L geometry, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0400.L4 TI22 The indexable insert S229.0400.L4 Ti22 with a cutting width of 4 mm is suitable for grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.N2.G AS45 The indexable insert with a cutting width of 4 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0400.N4.G AS45 The indexable insert with a cutting width of 4 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.34 AL96 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0500.34 AS62 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0500.34 AS66 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0500.34 TC92 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0500.34 TF45 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0500.34 TI22 Indexable insert S229.0500.34 Ti22 for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0500.34 TI25 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0500.34 TN32 The indexable insert with a cutting width of 5 mm is suitable for grooving, turning and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.34 TN35 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0500.54 AS62 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0500.54 TC92 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0500.54 TF45 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0500.54 TI22 The indexable insert S229.0500.54 Ti22 with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0500.54 TI25 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0500.54 TN32 The indexable insert with a cutting width of 5 mm is suitable for grooving, turning and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.54 TN35 The indexable insert with a cutting width of 5 mm is suitable for grooving, turning and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.A4 AS62 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0500.A4 TC92 The indexable insert with a cutting width of 5 mm is suitable for grooving, turning and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.A4 TF45 The indexable insert with a cutting width of 5 mm is suitable for grooving, turning and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.A4 TI22 Indexable insert S229.0500.A4 Ti22 for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0500.A4 TN32 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0500.A4 TN35 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0500.A6 AS62 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0500.A6 TI25 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0500.H4 AL96 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.H4 TF42 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry H, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0500.H6 AL96 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.H6 TF42 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.H8 AL96 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.H8 TF42 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.HR4 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry HR, matching clamp holder for. B. H210. |
|
Paul Horn S229.0500.HR4 AS62 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.HR6 AS62 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.HR8 AS62 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.L4 AL96 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.L4 AS62 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, L geometry, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0500.L4 AS66 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, L geometry, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0500.L4 TF42 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, L geometry, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0500.L4 TI22 The indexable insert S229.0500.L4 Ti22 with a cutting width of 5 mm is suitable for grooving, turning and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.L6 AL96 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0500.L6 AS62 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0500.L6 AS66 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0500.L6 TF42 The indexable insert with a cutting width of 5 mm is suitable for grooving, turning and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.L6 TI22 The indexable insert S229.0500.L6 Ti22 with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0500.L8 AS62 The indexable insert with a cutting width of 5 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0500.L8 AS66 Indexable insert for grooving and turning with a cutting width of 5 mm, corner radius 0.8 mm and maximum groove depth of 25 mm, L geometry, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0500.N2.G TI25 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.N4.G AS45 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.N4.G AS62 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.N4.G TI25 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.N6.G AS45 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.N6.G AS62 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.N6.G TI25 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0500.N8.G AS62 The indexable insert with a cutting width of 5 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0600.34 AL96 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0600.34 AS62 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0600.34 AS66 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0600.34 TC92 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0600.34 TF45 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0600.34 TI22 The indexable insert S229.0600.34 Ti22 with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0600.34 TI25 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0600.34 TN32 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0600.34 TN35 The indexable insert with a cutting width of 6 mm is suitable for grooving, turning and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0600.36 TI22 Indexable insert S229.0600.36 Ti22 for grooving and turning with a cutting width of 6 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0600.38 AL96 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0600.38 AS62 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.8 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0600.38 TC92 The indexable insert with a cutting width of 6 mm is suitable for grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0600.54 AL96 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0600.54 AS62 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0600.54 TC92 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0600.54 TF45 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0600.54 TI25 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0600.54 TN32 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0600.54 TN35 The indexable insert with a cutting width of 6 mm is suitable for grooving, turning and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0600.58 AS62 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0600.A4 AL96 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0600.A4 AS62 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0600.A4 TC92 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0600.A4 TF42 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0600.A4 TF45 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0600.A4 TI22 The indexable insert S229.0600.A4 Ti22 with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0600.A4 TI25 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0600.A4 TN32 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0600.A4 TN35 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0600.A8 AS62 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0600.H4 AL96 The indexable insert with a cutting width of 6 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0600.H4 TF42 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, Geometry H, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0600.H6 AL96 The indexable insert with a cutting width of 6 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0600.H6 TF42 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, Geometry H, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0600.H8 TF42 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.8 mm and maximum groove depth of 25 mm, Geometry H, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0600.HK AL96 The indexable insert with a cutting width of 6 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0600.HK TF42 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 1.2 mm and maximum groove depth of 25 mm, Geometry H, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0600.HR4 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, geometry HR, matching clamp holder for. B. H210. |
|
Paul Horn S229.0600.HR4 AS62 The indexable insert with a cutting width of 6 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0600.HR6 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry HR, matching clamp holder for. B. H210. |
|
Paul Horn S229.0600.HR6 AS62 The indexable insert with a cutting width of 6 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0600.HR8 AS62 The indexable insert with a cutting width of 6 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0600.L4 AL96 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0600.L4 AS62 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0600.L4 AS66 Indexable insert for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, L geometry, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0600.L4 TF42 The indexable insert with a cutting width of 6 mm is suitable for grooving, turning and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0600.L4 TI22 Indexable insert S229.0600.L4 Ti22 for grooving and turning with a cutting width of 6 mm, corner radius 0.4 mm and maximum groove depth of 25 mm, L geometry, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0600.L4PG AS62 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0600.L6 AL96 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0600.L6 AS62 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0600.L6 AS66 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0600.L6 TF42 The indexable insert with a cutting width of 6 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0600.L6 TI22 The indexable insert S229.0600.L6 Ti22 with a cutting width of 6 mm is suitable for grooving, turning and grooving of the inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0600.N4.G AS45 The indexable insert with a cutting width of 6 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0600.N6.G AS45 The indexable insert with a cutting width of 6 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0700.36 AS62 Indexable insert for grooving and turning with a cutting width of 7 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0700.36 TC92 Indexable insert for grooving and turning with a cutting width of 7 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0700.36 TI25 Indexable insert for grooving and turning with a cutting width of 7 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0700.36 TN35 Indexable insert for grooving and turning with a cutting width of 7 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0700.56 AS62 The indexable insert with a cutting width of 7 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0700.56 TC92 Indexable insert for grooving and turning with a cutting width of 7 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0700.56 TI22 The indexable insert S229.0700.56 Ti22 with a cutting width of 7 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0700.A6 TF42 Indexable insert for grooving and turning with a cutting width of 7 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0700.A6 TN32 The indexable insert with a cutting width of 7 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0800.36 AS62 The indexable insert with a cutting width of 8 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0800.36 TC92 Indexable insert for grooving and turning with a cutting width of 8 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0800.36 TI22 Indexable insert S229.0800.36 Ti22 for grooving and turning with a cutting width of 8 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0800.36 TI25 Indexable insert for grooving and turning with a cutting width of 8 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0800.36 TN32 Indexable insert for grooving and turning with a cutting width of 8 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.0800.36 TN35 The indexable insert with a cutting width of 8 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0800.56 AL96 The indexable insert with a cutting width of 8 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0800.56 AS62 Indexable insert for grooving and turning with a cutting width of 8 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0800.56 TC92 Indexable insert for grooving and turning with a cutting width of 8 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0800.56 TI22 The indexable insert S229.0800.56 Ti22 with a cutting width of 8 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0800.56 TN32 Indexable insert for grooving and turning with a cutting width of 8 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0800.58 TC92 The indexable insert with a cutting width of 8 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0800.58 TF42 The indexable insert with a cutting width of 8 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0800.58 TI22 Indexable insert S229.0800.58 Ti22 for grooving and turning with a cutting width of 8 mm, corner radius 0.8 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.0800.5K TI22 The indexable insert S229.0800.5K Ti22 with a cutting width of 8 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0800.A6 TI22 The indexable insert S229.0800.A6 Ti22 with a cutting width of 8 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0800.A6 TN32 Indexable insert for grooving and turning with a cutting width of 8 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, Geometry A, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0800.HR8PG AS62 The indexable insert with a cutting width of 8 mm is suitable for penetration of inner and outer contours with up to 25 mm depth. |
|
Paul Horn S229.0800.L6 AL96 The indexable insert with a cutting width of 8 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0800.L6 AS62 Indexable insert for grooving and turning with a cutting width of 8 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, L geometry, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0800.L6 AS66 Indexable insert for grooving and turning with a cutting width of 8 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, L geometry, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0800.L6 TF42 Indexable insert for grooving and turning with a cutting width of 8 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, L geometry, suitable for clamping holder. B. H210. |
|
Paul Horn S229.0800.L6 TI22 The indexable insert S229.0800.L6 Ti22 with a cutting width of 8 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.0800.L8PG AS62 The indexable insert with a cutting width of 8 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.1000.36 AS62 The indexable insert with a cutting width of 10 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.1000.36 TC92 Indexable insert for grooving and turning with a cutting width of 10 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.1000.36 TI25 Indexable insert for grooving and turning with a cutting width of 10 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.1000.36 TN32 The indexable insert with a cutting width of 10 mm is suitable for grooving and turning of internal and external contours with up to 25 mm depth. |
|
Paul Horn S229.1000.36 TN35 Indexable insert for grooving and turning with a cutting width of 10 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 3, matching clamp holder for. B. H210. |
|
Paul Horn S229.1000.56 TI22 Indexable insert S229.1000.56 Ti22 for grooving and turning with a cutting width of 10 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.1000.56 TN32 Indexable insert for grooving and turning with a cutting width of 10 mm, corner radius 0.6 mm and maximum groove depth of 25 mm, geometry 5, matching clamp holder z. B. H210. |
|
Paul Horn S229.F040.1344 PD75 The insert S229.F040.1344 Pd75 with a cutting width of 4 mm is suitable for gloss turning of wheels. |
|
Paul Horn S229.F040.1345 PD75 The insert S229.F040.1345 Pd75 with a cutting width of 4 mm is suitable for gloss turning of wheels. |
|
Paul Horn S229.F040.FN.00 PD75 The insert S229.F040.FN.00 Pd75 with a cutting width of 4 mm is suitable for gloss turning of wheels. |
|
Paul Horn S229.F040.TN.22 PD75 The insert S229.F040.FN.00 Pd75 with a cutting width of 4 mm is suitable for gloss turning of wheels. |
|
Paul Horn S229.F080.KH8 K10 The indexable insert with a cutting width of 8 mm is suitable for grooving and copy turning of internal and external contours with up to 0.6 mm deep. |
|
Paul Horn S229.F080.KI8 K10 The indexable insert with a cutting width of 8 mm is suitable for grooving and copy turning of internal and external contours with up to 0.6 mm deep. |
|
Paul Horn S229.F080.KJ8 K10 The indexable insert with a cutting width of 8 mm is suitable for grooving and copy turning of internal and external contours with up to 0.6 mm deep. |
|
Paul Horn S229.F080.TN.H2 PD75 The insert S229.F080.TN.H2 Pd75 with a cutting width of 8 mm is suitable for grooving and copy turning of internal and external contours with up to 0.6 mm deep. |
|
Paul Horn S229.F080.TN.S2 PD75 The insert S229.F080.TN.S2 Pd75 with a cutting width of 8 mm is suitable for grooving and copy turning of internal and external contours with up to 0.6 mm deep. |
|
Paul Horn S25A.0200.10.10 TH35 The indexable insert with a cutting width of 2 mm is suitable for grooving up to 15 mm depth. |
|
Paul Horn S25A.0200.12 TH35 The indexable insert with a cutting width of 2 mm is suitable for grooving up to 15 mm depth. |
|
Paul Horn S25A.0300.10.15 TH35 The indexable insert with a cutting width of 3 mm is suitable for grooving up to 15 mm depth. |
|
Paul Horn S25A.0300.12 TH35 The indexable insert with a cutting width of 3 mm is suitable for grooving up to 15 mm depth. |
|
Paul Horn S25A.0400.10.20 TH35 The indexable insert with a cutting width of 4 mm is suitable for grooving up to 20 mm depth. |
|
Paul Horn S25A.0400.12 TH35 The indexable insert with a cutting width of 4 mm is suitable for grooving up to 20 mm depth. |
|
Paul Horn S264.0150.D1 MG12 The indexable insert with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 16 mm depth. |
|
Paul Horn S264.0150.D1 TN35 Indexable insert with a cutting width of 1.5 mm and maximum cutting depth of 16 mm is suitable for grooving and turning of outer contours. |
|
Paul Horn S264.0200.D1 MG12 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 16 mm depth. |
|
Paul Horn S264.0200.D1 TN35 Indexable insert with a cutting width of 2 mm and maximum cutting depth of 16 mm is suitable for grooving and turning of outer contours. |
|
Paul Horn S264.0250.D1 TN35 Indexable insert with a cutting width of 2.5 mm and maximum cutting depth of 16 mm is suitable for grooving and turning of outer contours. |
|
Paul Horn S264.0300.D1 TN35 The indexable insert with a cutting width of 3 mm is suitable for parting and grooving of outer contours with up to 16 mm depth. |
|
Paul Horn S29F.F080.FN.S2 PD75 The insert S29F.F080.FN.S2 Pd75 with a cutting width of 8 mm is suitable for internal machining and zumHinterdrehen of wheels of up to 0.6 mm penetration depth. |
|
Paul Horn S29F.F080.KJ8 K10 The indexable insert with a cutting width of 8 mm is suitable for penetration and rear turning inner contours with up to 0.6 mm deep. |
|
Paul Horn S312.0200.C2 TF46 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn S312.0200.C2 TI25 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn S312.0200.D2 AS62 The indexable insert with a cutting width of 2 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0200.D2 AS66 The indexable insert with a cutting width of 2 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0200.D2 TF46 The indexable insert with a cutting width of 2 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0200.D2 TI25 The indexable insert with a cutting width of 2 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0200.D2 TN32 The indexable insert with a cutting width of 2 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0200.D4 AS62 The indexable insert with a cutting width of 2 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0200.D4 AS66 Indexable insert for grooving, turning and parting with a cutting width of 2 mm, corner radius of 0.4 mm and a maximum groove depth of 5 mm, D geometry, suitable for clamping holder. B. H360. |
|
Paul Horn S312.0200.D4 TI25 Indexable insert for grooving, turning and parting with a cutting width of 2 mm, corner radius of 0.4 mm and a maximum groove depth of 5 mm, D geometry, suitable for clamping holder. B. H360. |
|
Paul Horn S312.0200.F2 TF46 The indexable insert with a cutting width of 2 mm is suitable for tapping inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0200.F2 TI25 The indexable insert with a cutting width of 2 mm is suitable for tapping inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0250.52 AL96 The indexable insert with a cutting width of 2.5 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth. |
|
Paul Horn S312.0250.52 AS62 Indexable insert for grooving, turning and parting with a cutting width of 2.5 mm, corner radius of 0.2 mm and a maximum groove depth of 8 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0250.52 TF45 Indexable insert for grooving, turning and parting with a cutting width of 2.5 mm, corner radius of 0.2 mm and a maximum groove depth of 8 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0250.52 TF46 Indexable insert for grooving, turning and parting with a cutting width of 2.5 mm, corner radius of 0.2 mm and a maximum groove depth of 8 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0250.52 TI25 Indexable insert for grooving, turning and parting with a cutting width of 2.5 mm, corner radius of 0.2 mm and a maximum groove depth of 8 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0250.52 TN32 The indexable insert with a cutting width of 2.5 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth. |
|
Paul Horn S312.0250.54 AS62 The indexable insert with a cutting width of 2.5 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth. |
|
Paul Horn S312.0250.54 AS66 Indexable insert for grooving, turning and parting with a cutting width of 2.5 mm, corner radius of 0.4 mm and a maximum groove depth of 8 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0250.54 TF45 Indexable insert for grooving, turning and parting with a cutting width of 2.5 mm, corner radius of 0.4 mm and a maximum groove depth of 8 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0250.54 TF46 Indexable insert for grooving, turning and parting with a cutting width of 2.5 mm, corner radius of 0.4 mm and a maximum groove depth of 8 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0250.54 TI25 Indexable insert for grooving, turning and parting with a cutting width of 2.5 mm, corner radius of 0.4 mm and a maximum groove depth of 8 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0250.54 TN32 Indexable insert for grooving, turning and parting with a cutting width of 2.5 mm, corner radius of 0.4 mm and a maximum groove depth of 8 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0250.54 TN35 The indexable insert with a cutting width of 2.5 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth. |
|
Paul Horn S312.0250.C2 TF46 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn S312.0250.C2 TI25 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn S312.0250.D2 AS62 The indexable insert with a cutting width of 2.5 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0250.D2 AS66 Indexable insert for grooving, turning and parting with a cutting width of 2.5 mm, corner radius of 0.2 mm and a maximum groove depth of 5 mm, D geometry, suitable for clamping holder. B. H360. |
|
Paul Horn S312.0250.D2 TC92 The indexable insert with a cutting width of 2.5 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0250.D2 TF45 Indexable insert for grooving, turning and parting with a cutting width of 2.5 mm, corner radius of 0.2 mm and a maximum groove depth of 5 mm, D geometry, suitable for clamping holder. B. H360. |
|
Paul Horn S312.0250.D2 TF46 The indexable insert with a cutting width of 2.5 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0250.D2 TI25 The indexable insert with a cutting width of 2.5 mm is suitable for parting and grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0250.D2 TN32 The indexable insert with a cutting width of 2.5 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0250.D4 AS62 The indexable insert with a cutting width of 2.5 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0250.D4 AS66 Indexable insert for grooving, turning and parting with a cutting width of 2.5 mm, corner radius of 0.4 mm and a maximum groove depth of 5 mm, D geometry, suitable for clamping holder. B. H360. |
|
Paul Horn S312.0250.D4 TC92 The indexable insert with a cutting width of 2.5 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0250.D4 TF45 Indexable insert for grooving, turning and parting with a cutting width of 2.5 mm, corner radius of 0.4 mm and a maximum groove depth of 5 mm, D geometry, suitable for clamping holder. B. H360. |
|
Paul Horn S312.0250.D4 TF46 Indexable insert for grooving, turning and parting with a cutting width of 2.5 mm, corner radius of 0.4 mm and a maximum groove depth of 5 mm, D geometry, suitable for clamping holder. B. H360. |
|
Paul Horn S312.0250.D4 TI25 Indexable insert for grooving, turning and parting with a cutting width of 2.5 mm, corner radius of 0.4 mm and a maximum groove depth of 5 mm, D geometry, suitable for clamping holder. B. H360. |
|
Paul Horn S312.0250.D4 TN32 The indexable insert with a cutting width of 2.5 mm is suitable for tapping inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0250.F2 TF46 The indexable insert with a cutting width of 2.5 mm is suitable for parting and grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0250.F2 TI25 The indexable insert with a cutting width of 2.5 mm is suitable for parting and grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0300.52 AS62 The indexable insert with a cutting width of 3 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0300.52 AS66 Indexable insert for grooving, turning and parting with a cutting width of 3 mm, corner radius of 0.2 mm and a maximum groove depth of 5 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0300.52 TC92 Indexable insert for grooving, turning and parting with a cutting width of 3 mm, corner radius of 0.2 mm and a maximum groove depth of 5 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0300.52 TF45 The indexable insert with a cutting width of 3 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0300.52 TF46 The indexable insert with a cutting width of 3 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0300.52 TI25 Indexable insert for grooving, turning and parting with a cutting width of 3 mm, corner radius of 0.2 mm and a maximum groove depth of 5 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0300.52 TN32 The indexable insert with a cutting width of 3 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0300.54 AS62 The indexable insert with a cutting width of 3 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0300.54 TF46 The indexable insert with a cutting width of 3 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0300.C2 TF46 The indexable insert with a cutting width of 3 mm is suitable for parting and grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0300.C2 TI25 Indexable insert for grooving, turning and parting with a cutting width of 3 mm, corner radius of 0.2 mm and a maximum groove depth of 5 mm, geometry C, suitable for clamping holder. B. H360. |
|
Paul Horn S312.0300.D2 AS62 The indexable insert with a cutting width of 3 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0300.D2 AS66 Indexable insert for grooving, turning and parting with a cutting width of 3 mm, corner radius of 0.2 mm and a maximum groove depth of 5 mm, D geometry, suitable for clamping holder. B. H360. |
|
Paul Horn S312.0300.D2 TF45 The indexable insert with a cutting width of 3 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0300.D2 TF46 The indexable insert with a cutting width of 3 mm is suitable for tapping inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0300.D2 TI25 The indexable insert with a cutting width of 3 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0300.D2 TN32 Indexable insert for grooving, turning and parting with a cutting width of 3 mm, corner radius of 0.2 mm and a maximum groove depth of 5 mm, D geometry, suitable for clamping holder. B. H360. |
|
Paul Horn S312.0300.D4 AS62 The indexable insert with a cutting width of 3 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0400.52 AS62 The indexable insert with a cutting width of 4 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0400.52 AS66 Indexable insert for grooving, turning and parting with a cutting width of 4 mm, corner radius of 0.2 mm and a maximum groove depth of 5 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0400.52 TF46 Indexable insert for grooving, turning and parting with a cutting width of 4 mm, corner radius of 0.2 mm and a maximum groove depth of 5 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0400.52 TI25 The indexable insert with a cutting width of 4 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0400.54 AS62 The indexable insert with a cutting width of 4 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0400.54 AS66 Indexable insert for grooving, turning and parting with a cutting width of 4 mm, corner radius of 0.4 mm and a maximum groove depth of 5 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0400.54 TF46 Indexable insert for grooving, turning and parting with a cutting width of 4 mm, corner radius of 0.4 mm and a maximum groove depth of 5 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0400.54 TI25 Indexable insert for grooving, turning and parting with a cutting width of 4 mm, corner radius of 0.4 mm and a maximum groove depth of 5 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0400.54 TN32 The indexable insert with a cutting width of 4 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0400.F2 TF46 The indexable insert with a cutting width of 4 mm is suitable for parting and grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0400.F4 TF46 The indexable insert with a cutting width of 4 mm is suitable for parting and grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0400.F4 TI25 Indexable insert for grooving, turning and parting with a cutting width of 4 mm, corner radius of 0.4 mm and a maximum groove depth of 5 mm, geometry F, suitable for clamping holder. B. H360. |
|
Paul Horn S312.0500.52 AS62 The indexable insert with a cutting width of 5 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0500.52 AS66 Indexable insert for grooving, turning and parting with a cutting width of 5 mm, corner radius of 0.2 mm and a maximum groove depth of 5 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0500.52 TF46 Indexable insert for grooving, turning and parting with a cutting width of 5 mm, corner radius of 0.2 mm and a maximum groove depth of 5 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0500.52 TN32 The indexable insert with a cutting width of 5 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0500.54 AS62 The indexable insert with a cutting width of 5 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0500.54 AS66 Indexable insert for grooving, turning and parting with a cutting width of 5 mm, corner radius of 0.4 mm and a maximum groove depth of 5 mm, geometry 5, matching clamp holder z. B. H360. |
|
Paul Horn S312.0500.54 TF46 The indexable insert with a cutting width of 5 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0500.54 TI25 The indexable insert with a cutting width of 5 mm is suitable for grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0500.F2 TF46 The indexable insert with a cutting width of 5 mm is suitable for parting and grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S312.0500.F4 TF46 The indexable insert with a cutting width of 5 mm is suitable for parting and grooving of the inner and outer contours with up to 5 mm depth. |
|
Paul Horn S34T.0200.32 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0200.34 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0200.D2 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0200.D4 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0250.32 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0250.34 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0250.52 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0250.54 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0250.D2 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0250.D4 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0300.32 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0300.34 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0300.52 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0300.54 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0300.D2 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0300.D4 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0400.32 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0400.34 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0400.52 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0400.54 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
|
Paul Horn S34T.0500.32 AS45 Indexable insert TiAlN nano-structured coated carbide insert |
