|
Paul Horn LS114.0200.1.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 16.5 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 6.5 mm deep. |
|
Paul Horn LS114.0200.D2 TF45 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn LS114.0200.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn LS114.0200.D2 TN35 Insert to Inneneinstechen of grooves from bore diameter 14 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn LS114.0250.1.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 16.5 mm with 2.5 mm width (nose radius 0.2 mm) and a maximum of 6.5 mm deep. |
|
Paul Horn LS114.0250.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 2.5 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn LS114.0250.D2 TN35 Insert to Inneneinstechen of grooves from bore diameter 14 mm with 2.5 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn LS114.0300.1.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 16.5 mm with 3 mm width (nose radius 0.2 mm) and a maximum of 6.5 mm deep. |
|
Paul Horn LS114.0300.D2 TF45 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 3 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn LS114.0300.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 3 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn LS114.0300.D2 TN35 Insert to Inneneinstechen of grooves from bore diameter 14 mm with 3 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn LS114.1890.R2 TH35 Insert for internal turning and copying from bore diameter 13.8 mm with a corner radius of 0.2 mm. |
|
Paul Horn LS114.1890.R4 TH35 Insert for internal turning and copying from bore diameter 13.8 mm with a corner radius of 0.4 mm. |
|
Paul Horn LS116.0200.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 16 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn LS116.0250.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 16 mm with width 2.5 mm (corner radius 0.2 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn LS116.0300.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 16 mm with 3 mm width (nose radius 0.2 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn LS116.1897.R2 TH35 Insert for internal turning and copying from bore diameter 15.5 mm with a corner radius of 0.2 mm. |
|
Paul Horn LS116.1897.R4 TH35 Insert for internal turning and copying from bore diameter 15.5 mm with a corner radius of 0.4 mm. |
|
Paul Horn LS117.300.00.A0.10 MD10 The insert with a cutting width of 3.5 mm is suitable for polish turning of internal and external contours. |
|
Paul Horn LS117.300.00.K0.10 MD10 The insert with a cutting width of 3.5 mm is suitable for polish turning of internal and external contours. |
|
Paul Horn LS117.300.00.M0.10 MD10 The insert with a cutting width of 3.5 mm is suitable for polish turning of internal and external contours. |
|
Paul Horn LS11P.0150.1.D1 TH35 The insert with a cutting width of 1.5 mm is suitable for penetration of inner contours with up to 2.5 mm deep. |
|
Paul Horn LS11P.0150.2.D1 TH35 The insert with a cutting width of 1.5 mm is suitable for penetration of inner contours with up to 3.5 mm deep. |
|
Paul Horn LS11P.0200.1.D2 TH35 The insert with a cutting width of 2 mm is suitable for penetration of inner contours with depths up to 2.5 mm. |
|
Paul Horn LS11P.0200.2.D2 TH35 The insert with a cutting width of 2 mm is suitable for penetration of inner contours with up to 3.5 mm deep. |
|
Paul Horn LS11P.0250.1.D2 TH35 The insert with a cutting width of 2.5 mm is suitable for penetration of inner contours with depths up to 2.5 mm. |
|
Paul Horn LS11P.0250.2.D2 TH35 The insert with a cutting width of 2.5 mm is suitable for penetration of inner contours with up to 3.5 mm deep. |
|
Paul Horn LS11P.1859.R2 TH35 The insert suitable for bore-rotating inner contours. |
|
Paul Horn LS11P.1859.R4 TH35 The insert suitable for bore-rotating inner contours. |
|
Paul Horn LS123.0420.C0 TN35 Indexable insert TiN coated |
|
Paul Horn LS123.0420.C1 TI25 The insert with a cutting width of 2 mm is suitable for tapping up to 25 mm depth. |
|
Paul Horn LS123.0420.C1 TN35 Indexable insert TiN coated |
|
Paul Horn LS123.0820.C0 TI25 Insert to butzenarmen parting with a cutting width of 2 mm, with geometry C0 and Abstechschräge 8 °, Model Links. |
|
Paul Horn LS123.1520.C0 TI25 Insert to butzenarmen parting with a cutting width of 2 mm, with geometry C0 and Abstechschräge 15 °, Model Links. |
|
Paul Horn LS123.1520.C1 TF45 The insert with a cutting width of 2 mm is suitable for tapping up to 25 mm depth. |
|
Paul Horn LS18P.0200.1.D2 TH35 The insert with a cutting width of 2 mm is suitable for grooving of the inner edges up to 6 mm depth. |
|
Paul Horn LS18P.0200.2.D2 TH35 The insert with a cutting width of 2 mm is suitable for grooving of the inner edges up to 8 mm depth. |
|
Paul Horn LS18P.0250.1.D2 TH35 The insert with a cutting width of 2.5 mm is suitable for grooving of the inner edges up to 6 mm depth. |
|
Paul Horn LS18P.0250.2.D2 TH35 The insert with a cutting width of 2.5 mm is suitable for grooving of the inner edges up to 8 mm depth. |
|
Paul Horn LS18P.0300.1.D2 TH35 The insert with a cutting width of 3 mm is suitable for grooving of the inner edges up to 6 mm depth. |
|
Paul Horn LS18P.0300.2.D2 TH35 The insert with a cutting width of 3 mm is suitable for grooving of the inner edges up to 8 mm depth. |
|
Paul Horn LS18P.1815.R2 TH35 The insert suitable for bore-turning and turning inside contours. |
|
Paul Horn LS18P.1815.R4 TH35 The insert suitable for bore-turning and turning inside contours. |
|
Paul Horn LS223.0420.C0 TF45 Indexable insert for butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 11 mm, with geometry C and 4 ° Abstechschräge, execution Links. |
|
Paul Horn LS223.0420.C0 TI25 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn LS223.0420.C0 TN35 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn LS223.0420.C1 TN35 Indexable insert to butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 11 mm, with geometry C and 4 ° Abstechschräge, execution Links. |
|
Paul Horn LS223.0425.C0 TN35 Indexable insert to butzenarmen parting with a cutting width of 2.5 mm and a maximum insertion depth of 11 mm, with geometry C and 4 ° Abstechschräge, execution Links. |
|
Paul Horn LS223.0425.C1 TN35 Indexable insert to butzenarmen parting with a cutting width of 2.5 mm and a maximum insertion depth of 11 mm, with geometry C and 4 ° Abstechschräge, execution Links. |
|
Paul Horn LS223.0430.C0 TF45 Indexable insert TiAlN coated |
|
Paul Horn LS223.0430.C0 TN35 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 11 mm, with geometry C and 4 ° Abstechschräge, execution Links. |
|
Paul Horn LS223.0430.C1 TN35 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 11 mm, with geometry C and 4 ° Abstechschräge, execution Links. |
|
Paul Horn LS223.0820.C0 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn LS223.0820.C0 TI25 Indexable insert to butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 11 mm, with geometry C and 8 ° Abstechschräge, execution Links. |
|
Paul Horn LS223.0820.C0 TN35 Indexable insert to butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 11 mm, with geometry C and 8 ° Abstechschräge, execution Links. |
|
Paul Horn LS223.0820.C1 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn LS223.0820.C1 TN35 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn LS223.0825.C0 TF45 Indexable insert TiAlN coated |
|
Paul Horn LS223.0825.C0 TN35 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn LS223.0825.C1 TF45 Indexable insert for butzenarmen parting with a cutting width of 2.5 mm and a maximum insertion depth of 11 mm, with geometry C and 8 ° Abstechschräge, execution Links. |
|
Paul Horn LS223.0830.C0 TF45 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn LS223.0830.C0 TI25 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 11 mm, with geometry C and 8 ° Abstechschräge, execution Links. |
|
Paul Horn LS223.0830.C0 TN35 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 11 mm, with geometry C and 8 ° Abstechschräge, execution Links. |
|
Paul Horn LS223.0830.C1 TI25 Indexable insert TiCN coated |
|
Paul Horn LS223.1520.C0 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn LS223.1520.C0 TI25 Indexable insert to butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 11 mm, with geometry C and Abstechschräge 15 °, Model Links. |
|
Paul Horn LS223.1520.C0 TN35 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn LS223.1520.C1 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn LS223.1520.C1 TI25 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn LS223.1520.C1 TN35 Indexable insert to butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 11 mm, with geometry C and Abstechschräge 15 °, Model Links. |
|
Paul Horn LS224.0305.02 TF45 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.5 mm. |
|
Paul Horn LS224.0407.02 TF45 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.75 mm. |
|
Paul Horn LS224.0520.C0 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0520.C0 TN35 Indexable insert to butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 18 mm, with geometry C and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS224.0520.C1 TF45 Indexable insert for butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 18 mm, with geometry C and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS224.0520.C1 TN35 Indexable insert to butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 18 mm, with geometry C and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS224.0520.E2 AS62 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0520.F2 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0520.F2 TF46 Indexable insert for butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 18 mm, with geometry F and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS224.0525.C0 TF45 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0525.C0 TN35 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0525.C1 TF45 Indexable insert for butzenarmen parting with a cutting width of 2.5 mm and a maximum insertion depth of 18 mm, with geometry C and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS224.0525.C1 TN35 Indexable insert to butzenarmen parting with a cutting width of 2.5 mm and a maximum insertion depth of 18 mm, with geometry C and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS224.0525.E2 AS62 The indexable insert with a cutting width of 2.5 mm is suitable for tapping. |
|
Paul Horn LS224.0525.F2 TF43 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0525.F2 TF45 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0530.C0 TC92 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0530.C0 TF45 Indexable insert for butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 18 mm, with geometry C and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS224.0530.C0 TN35 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0530.C1 TF45 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0530.C1 TN35 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0530.E2 AS62 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0530.E2 TC92 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0530.E2 TF43 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0530.E2 TF45 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0530.F2 TF43 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0530.F2 TF45 Indexable insert for butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 18 mm, with geometry F and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS224.0530.F2 TI22 The indexable insert LS224.0530.F2 Ti22 with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0610.02 TF45 The indexable insert full profile is suitable for threading metric threads with a pitch of 1 mm. |
|
Paul Horn LS224.0712.02 TF45 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.25mm. |
|
Paul Horn LS224.0820.C0 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0820.C0 TN35 Indexable insert to butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 18 mm, with geometry C and 8 ° Abstechschräge, execution Links. |
|
Paul Horn LS224.0820.C1 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0825.C0 TN35 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0825.C1 TF45 Indexable insert for butzenarmen parting with a cutting width of 2.5 mm and a maximum insertion depth of 18 mm, with geometry C and 8 ° Abstechschräge, execution Links. |
|
Paul Horn LS224.0830.C0 TF45 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0830.C0 TN35 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0830.C1 TF45 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.0830.C1 TN35 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 18 mm, with geometry C and 8 ° Abstechschräge, execution Links. |
|
Paul Horn LS224.0915.02 TF45 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.5 mm. |
|
Paul Horn LS224.1017.02 TF45 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.75 mm. |
|
Paul Horn LS224.1220.02 TF45 The indexable insert full profile is suitable for threading metric threads with a pitch of 2 mm. |
|
Paul Horn LS224.1520.C0 TC92 Indexable insert to butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 18 mm, with geometry C and Abstechschräge 15 °, Model Links. |
|
Paul Horn LS224.1520.C0 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.1520.C0 TN35 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.1520.C1 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS224.1520.C1 TN35 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn LS229.0530.32 AS62 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn LS229.0530.32 TC92 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with 30 geometry and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS229.0530.32 TF45 Indexable insert for butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with 30 geometry and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS229.0530.32 TI25 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn LS229.0530.32 TN32 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with 30 geometry and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS229.0530.32 TN35 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with 30 geometry and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS229.0530.C0 TF45 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn LS229.0530.C0 TI25 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with geometry C and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS229.0530.C0 TN35 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn LS229.0530.C1 TI25 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn LS229.0530.C1 TN35 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with geometry C and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS229.0540.32 AS62 The indexable insert with a cutting width of 4 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn LS229.0540.32 TF45 The indexable insert with a cutting width of 4 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn LS229.0540.32 TI25 Indexable insert to butzenarmen parting with a cutting width of 4 mm and a maximum insertion depth of 25 mm, with 30 geometry and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS229.0540.32 TN32 Indexable insert to butzenarmen parting with a cutting width of 4 mm and a maximum insertion depth of 25 mm, with 30 geometry and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS229.0540.C0 TN35 The indexable insert with a cutting width of 4 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn LS229.0540.C1 TI25 Indexable insert to butzenarmen parting with a cutting width of 4 mm and a maximum insertion depth of 25 mm, with geometry C and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS229.0830.C0 TC92 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn LS229.0830.C0 TF45 Indexable insert for butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with geometry C and 8 ° Abstechschräge, execution Links. |
|
Paul Horn LS229.0830.C0 TI25 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with geometry C and 8 ° Abstechschräge, execution Links. |
|
Paul Horn LS229.0830.C0 TN35 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with geometry C and 8 ° Abstechschräge, execution Links. |
|
Paul Horn LS229.0830.C1 TF45 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn LS229.0830.C1 TI25 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with geometry C and 8 ° Abstechschräge, execution Links. |
|
Paul Horn LS229.0830.C1 TN35 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with geometry C and 8 ° Abstechschräge, execution Links. |
|
Paul Horn LS229.0840.C0 TN35 Indexable insert to butzenarmen parting with a cutting width of 4 mm and a maximum insertion depth of 25 mm, with geometry C and 8 ° Abstechschräge, execution Links. |
|
Paul Horn LS229.0840.C1 TN35 The indexable insert with a cutting width of 4 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn LS274.0035.04.20 TH35 The indexable insert suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0035.04.20.E TH35 The indexable insert suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0035.24.20 TH35 The indexable insert suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0050.01.10 TH35 The indexable insert with a cutting width of 0.5 mm is suitable for parting and grooving of outer contours with up to 1.5 mm deep. |
|
Paul Horn LS274.0050.01.10.E TH35 The indexable insert with a cutting width of 0.5 mm is suitable for parting and grooving of outer contours with up to 1.5 mm deep. |
|
Paul Horn LS274.0050.01.20 TH35 The indexable insert with a cutting width of 0.5 mm is suitable for parting and grooving of outer contours with up to 1.5 mm deep. |
|
Paul Horn LS274.0050.01.20.E TH35 The indexable insert with a cutting width of 0.5 mm is suitable for parting and grooving of outer contours with up to 1.5 mm deep. |
|
Paul Horn LS274.0050.01.M0 TH35 The indexable insert with a cutting width of 0.5 mm is suitable for parting and grooving of outer contours with up to 1.5 mm deep. |
|
Paul Horn LS274.0050.01.M0.E TH35 The indexable insert with a cutting width of 0.5 mm is suitable for parting and grooving of outer contours with up to 1.5 mm deep. |
|
Paul Horn LS274.0050.P0 AN25 The indexable insert with a cutting width of 0.5 mm is suitable for grooving and turning of outer contours with up to 1 mm depth. |
|
Paul Horn LS274.0055.04.20 TH35 The indexable insert suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0055.04.20.E TH35 The indexable insert suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0055.24.20 TH35 The indexable insert suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0060.04.10 TH35 The indexable insert suitable for reverse rotation of outer contours. |
|
Paul Horn LS274.0060.04.10.E TH35 The indexable insert suitable for reverse rotation of outer contours. |
|
Paul Horn LS274.0070.02.10 TH35 The indexable insert with a cutting width of 0.7 mm is suitable for parting and grooving of outer contours with up to 2 mm depth. |
|
Paul Horn LS274.0070.02.10.E TH35 The indexable insert with a cutting width of 0.7 mm is suitable for parting and grooving of outer contours with up to 2 mm depth. |
|
Paul Horn LS274.0070.02.20 TH35 The indexable insert with a cutting width of 0.7 mm is suitable for parting and grooving of outer contours with up to 2 mm depth. |
|
Paul Horn LS274.0070.02.20.E TH35 The indexable insert with a cutting width of 0.7 mm is suitable for parting and grooving of outer contours with up to 2 mm depth. |
|
Paul Horn LS274.0070.02.M0 TH35 The indexable insert with a cutting width of 0.7 mm is suitable for parting and grooving of outer contours with up to 2 mm depth. |
|
Paul Horn LS274.0070.02.M0.E TH35 The indexable insert with a cutting width of 0.7 mm is suitable for parting and grooving of outer contours with up to 2 mm depth. |
|
Paul Horn LS274.0080.03.10 TH35 The indexable insert with a cutting width of 0.8 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0080.03.10.E TH35 The indexable insert with a cutting width of 0.8 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0080.03.20 TH35 The indexable insert with a cutting width of 0.8 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0080.03.20.E TH35 The indexable insert with a cutting width of 0.8 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0080.03.M0 TH35 The indexable insert with a cutting width of 0.8 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0080.03.M0.E TH35 The indexable insert with a cutting width of 0.8 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0100.03.10 TH35 The indexable insert with a cutting width of 1 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0100.03.10.E TH35 The indexable insert with a cutting width of 1 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0100.03.20 TH35 The indexable insert with a cutting width of 1 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0100.03.20.E TH35 The indexable insert with a cutting width of 1 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0100.03.M0 TH35 The indexable insert with a cutting width of 1 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0100.03.M0.E TH35 The indexable insert RS274.0100.03.M0.E TH35 with a cutting width of 1 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0100.P0 AN25 The indexable insert with a cutting width of 1 mm is suitable for grooving and turning of outer contours with up to 2 mm depth. |
|
Paul Horn LS274.0120.03.10 TH35 The indexable insert with a cutting width of 1.2 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0120.03.10.E TH35 The indexable insert with a cutting width of 1.2 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0120.03.20.E TH35 The indexable insert with a cutting width of 1.2 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0120.03.M0 TH35 The indexable insert with a cutting width of 1.2 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0120.03.M0.E TH35 The indexable insert with a cutting width of 1.2 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0150.04.10 TH35 The indexable insert with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn LS274.0150.04.10.E TH35 The indexable insert with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn LS274.0150.04.20 The indexable insert TH35 with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn LS274.0150.04.20.E TH35 The indexable insert with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn LS274.0150.04.M0 The indexable insert TH35 with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn LS274.0150.04.M0.E TH35 The indexable insert with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn LS274.0150.06.10 TH35 The indexable insert with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn LS274.0150.06.10.E TH35 The indexable insert with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn LS274.0150.06.20 The indexable insert TH35 with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn LS274.0150.06.M0 The indexable insert TH35 with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn LS274.0150.06.M0.E TH35 The indexable insert with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn LS274.0150.P0 TH35 The indexable insert with a cutting width of 1.5 mm is suitable for grooving and turning of outer contours with up to 2:25 mm depth. |
|
Paul Horn LS274.0150.P0.E TH35 The indexable insert with a cutting width of 1.5 mm is suitable for longitudinal turning of outer contours with up to 2:25 mm depth. |
|
Paul Horn LS274.0200.04.10 TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn LS274.0200.04.10.E TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn LS274.0200.04.20 TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn LS274.0200.04.20.E TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn LS274.0200.04.M0 TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn LS274.0200.04.M0.E TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn LS274.0200.06.10 TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn LS274.0200.06.10.E TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn LS274.0200.06.20 TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn LS274.0200.06.20.E TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn LS274.0200.06.M0 TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn LS274.0200.06.M0.E TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn LS274.0200.P0 TH35 The indexable insert with a cutting width of 2 mm is suitable for grooving and turning of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0200.P0.E TH35 The indexable insert with a cutting width of 2 mm is suitable for grooving and turning of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0205.01.10 TH35 The indexable insert with a cutting width of 0.5 mm is suitable for tapping external contours with up to 1.5 mm deep. |
|
Paul Horn LS274.0205.01.10.E TH35 The indexable insert with a cutting width of 0.5 mm is suitable for longitudinal turning of outer contours with up to 1.5 mm deep. |
|
Paul Horn LS274.0235.04.20 TH35 The indexable insert RS274.0235.04.20 TH35 with a cutting width of 0.2 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0235.04.20.E TH35 The indexable insert RS274.0235.04.20.E TH35 with a cutting width of 0.2 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0235.24.20 TH35 The indexable insert with a cutting width of 0.2 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0250.P0 TH35 The indexable insert with a cutting width of 2.5 mm is suitable for grooving and turning of outer contours with up to 3.75 mm depth. |
|
Paul Horn LS274.0250.P0.E TH35 The indexable insert with a cutting width of 2.5 mm is suitable for grooving and turning of outer contours with up to 3.75 mm depth. |
|
Paul Horn LS274.0255.04.20 TH35 The indexable insert with a cutting width of 0.2 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0255.04.20.E TH35 The indexable insert with a cutting width of 0.2 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0255.24.20 TH35 The indexable insert with a cutting width of 0.2 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0300.P0 TH35 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of outer contours with up to 4.5 mm deep. |
|
Paul Horn LS274.0300.P0.E TH35 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of outer contours with up to 4.5 mm deep. |
|
Paul Horn LS274.0305.02 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.5 mm. |
|
Paul Horn LS274.0305.02.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.5 mm. |
|
Paul Horn LS274.0305.03 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.5 mm. |
|
Paul Horn LS274.0305.03.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.5 mm. |
|
Paul Horn LS274.0306.02 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.6 mm. |
|
Paul Horn LS274.0306.02.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.6 mm. |
|
Paul Horn LS274.0306.03 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.6 mm. |
|
Paul Horn LS274.0306.03.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.6 mm. |
|
Paul Horn LS274.0307.02 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.7 mm. |
|
Paul Horn LS274.0307.02.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.7 mm. |
|
Paul Horn LS274.0307.03 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.7 mm. |
|
Paul Horn LS274.0307.03.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.7 mm. |
|
Paul Horn LS274.0407.02 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.75 mm. |
|
Paul Horn LS274.0407.02.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.75 mm. |
|
Paul Horn LS274.0407.03 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.75 mm. |
|
Paul Horn LS274.0407.03.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.75 mm. |
|
Paul Horn LS274.0408.02 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.8 mm. |
|
Paul Horn LS274.0408.02.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.8 mm. |
|
Paul Horn LS274.0408.03 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.8 mm. |
|
Paul Horn LS274.0408.03.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.8 mm. |
|
Paul Horn LS274.0460.04.10 TH35 The indexable insert with a cutting width of 0.4 mm is suitable for reverse rotation of outer contours. |
|
Paul Horn LS274.0460.04.10.E TH35 The indexable insert with a cutting width of 0.4 mm is suitable for reverse rotation of outer contours. |
|
Paul Horn LS274.0460.04.M0 K10 The indexable insert with a cutting width of 0.4 mm is suitable for reverse rotation of outer contours. |
|
Paul Horn LS274.0460.04.M0.E K10 Indexable insert |
|
Paul Horn LS274.0460.04.M0.E TH35 The indexable insert with a cutting width of 0.4 mm is suitable for reverse rotation of outer contours. |
|
Paul Horn LS274.0510.03.10 TH35 The indexable insert LS274.0510.03.10 TH35 with a cutting width of 1 mm is suitable for grooving and turning of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0510.03.10.E TH35 The indexable insert LS274.0510.03.10.E TH35 with a cutting width of 1 mm is suitable for grooving and turning of outer contours with up to 3 mm in depth. |
|
Paul Horn LS274.0535.06.20 TH35 The indexable insert with a cutting width of 0.5 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0535.06.20.E TH35 The indexable insert with a cutting width of 0.5 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0535.26.20 TH35 The indexable insert with a cutting width of 0.5 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0555.06.20 TH35 The indexable insert with a cutting width of 0.5 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0555.06.20.E TH35 The indexable insert with a cutting width of 0.5 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0555.26.20 TH35 The indexable insert with a cutting width of 0.5 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn LS274.0560.06.11 TH35 The indexable insert with a cutting width of 0.5 mm is suitable for reverse rotation of outer contours. |
|
Paul Horn LS274.0560.06.11.E TH35 The indexable insert with a cutting width of 0.5 mm is suitable for reverse rotation of outer contours. |
|
Paul Horn LS274.0610.02 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1 mm. |
|
Paul Horn LS274.0610.02.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1 mm. |
|
Paul Horn LS274.0610.03 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1 mm. |
|
Paul Horn LS274.0712.02 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.25mm. |
|
Paul Horn LS274.0712.02.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.25mm. |
|
Paul Horn LS274.0712.03 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.25mm. |
|
Paul Horn LS274.0915.02 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.5 mm. |
|
Paul Horn LS274.0915.02.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.5 mm. |
|
Paul Horn LS274.0915.03 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.5 mm. |
|
Paul Horn LS274.1020.04.10 TH35 The indexable insert LS274.1020.04.10 TH35 with a cutting width of 2 mm is suitable for grooving and turning of outer contours with up to 4 mm depth. |
|
Paul Horn LS274.1020.04.10.E TH35 The indexable insert LS274.1020.04.10.E TH35 with a cutting width of 2 mm is suitable for grooving and turning of outer contours with up to 4 mm depth. |
|
Paul Horn LS274.1508.03.10 TH35 The indexable insert with a cutting width of 0.80 mm is suitable for tapping external contours with up to 3.00mm deep. |
|
Paul Horn LS274.1508.03.10.E TH35 The indexable insert with a cutting width of 0.80 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn LS274.1508.03.10R TH35 The indexable insert with a cutting width of 0.80 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn LS274.1508.03.1R.E TH35 The indexable insert LS274.1508.03.10R.E TH35 with a cutting width of 0.80 mm is suitable for tapping external contours with up to 3.00mm deep. |
|
Paul Horn LS274.1508.03.M0 TH35 The indexable insert with a cutting width of 0.80 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn LS274.1508.03.M0.E TH35 The indexable insert with a cutting width of 0.80 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn LS274.1508.03.M0R TH35 The indexable insert with a cutting width of 0.80 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn LS274.1510.03.10 TH35 The indexable insert with a cutting width of 1.00 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn LS274.1510.03.10.E TH35 The indexable insert with a cutting width of 1.00 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn LS274.1510.03.10R TH35 The indexable insert with a cutting width of 1.00 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn LS274.1510.03.1R.E TH35 The indexable insert with a cutting width of 1.00 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn LS274.1510.03.M0 TH35 The indexable insert with a cutting width of 1.00 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn LS274.1510.03.M0.E TH35 The indexable insert with a cutting width of 1.00 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn LS274.1510.03.M0R TH35 The indexable insert with a cutting width of 1.00 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn LS274.1510.05.M0R TH35 The indexable insert with a cutting width of 1 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn LS274.1515.04.10 TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn LS274.1515.04.10.E TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn LS274.1515.04.10R TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn LS274.1515.04.1R.E TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn LS274.1515.04.20 TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn LS274.1515.04.20.E TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn LS274.1515.04.20R TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn LS274.1515.04.M0 TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn LS274.1515.04.M0.E TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn LS274.1515.04.M0R TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn LS274.1515.06.M0R TH35 The indexable insert with a cutting width of 1.5 mm is suitable for tapping up to 6 mm depth. |
|
Paul Horn LS274.1520.06.10 TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn LS274.1520.06.10.E TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn LS274.1520.06.10R TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn LS274.1520.06.1R.E TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn LS274.1520.06.20 TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn LS274.1520.06.20.E TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn LS274.1520.06.20R TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn LS274.1520.06.M0 TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn LS274.1520.06.M0.E TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn LS274.1520.06.M0R TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn LS274.2047.03.SF AC25 Indexable insert |
|
Paul Horn LS274.2047.03.SF MG12 Indexable insert |
|
Paul Horn LS274.2508.03.SF AC25 Indexable insert |
|
Paul Horn LS274.2508.03.SF MG12 Indexable insert |
|
Paul Horn LS274.2508.04.SF AC25 Indexable insert |
|
Paul Horn LS274.2508.04.SF MG12 Indexable insert |
|
Paul Horn LS274.2508.04.SF.R TH35 Indexable insert |
|
Paul Horn LS274.2509.04.SF.R TH35 Indexable insert |
|
Paul Horn LS274.2510.06.SF.R TH35 Indexable insert |
|
Paul Horn LS274.2512.06.SF.R TH35 Indexable insert |
|
Paul Horn LS274.2515.06.SF.R TH35 Indexable insert |
|
Paul Horn LS274.4509.04.SF AC25 Indexable insert |
|
Paul Horn LS274.4509.04.SF MG12 Indexable insert |
|
Paul Horn LS275.0110.00 AS45 The indexable insert with a cutting width of 1.2 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn LS275.0110.40 TA45 The indexable insert with a cutting width of 1.2 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn LS275.0130.00 AS45 The indexable insert with a cutting width of 1.4 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn LS275.0130.40 TA45 The indexable insert with a cutting width of 1.4 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn LS275.0160.00 AS45 The indexable insert with a cutting width of 1.7 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn LS275.0160.40 TA45 The indexable insert with a cutting width of 1.7 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn LS275.0185.00 AS45 The indexable insert with a cutting width of 1.95 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn LS275.0185.40 TA45 The indexable insert with a cutting width of 1.95 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn LS275.0215.00 AS45 The indexable insert with a cutting width of 2.25 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn LS275.0215.40 TA45 The indexable insert with a cutting width of 2.25 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn LS275.0265.00 AS45 The indexable insert with a cutting width of 2.75 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn LS275.0265.40 TA45 The indexable insert with a cutting width of 2.75 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn LS275.0315.00 AS45 The indexable insert with a cutting width of 3.25 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn LS275.0315.40 TA45 The indexable insert with a cutting width of 3.25 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn LS275.1105.41 AS45 The indexable insert with a cutting width of 1.2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 0.5 mm deep. |
|
Paul Horn LS275.1308.41 AS45 The indexable insert with a cutting width of 1.4 mm is suitable for Nutzirkularfräsen of inner and outer contours of up to 0.85 mm depth. |
|
Paul Horn LS275.1610.51 AS45 The indexable insert LS275.1610.41 AS45 with a cutting width of 1.7 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 1 mm depth. |
|
Paul Horn LS275.1812.41 AS45 The indexable insert with a cutting width of 1.95 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 1.25mm deep. |
|
Paul Horn LS275.2115.41 AS45 The indexable insert with a cutting width of 2.25 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 1.5 mm deep. |
|
Paul Horn LS275.2617.41 AS45 The indexable insert with a cutting width of 2.75 mm is suitable for Nutzirkularfräsen of inner and outer contours of up to 1.75 mm depth. |
|
Paul Horn LS275.3118.41 AS45 The indexable insert with a cutting width of 3.25 mm is suitable for Nutzirkularfräsen of inner and outer contours of up to 1.75 mm depth. |
|
Paul Horn LS275.AT41.HM Balancing ring, plate dummy to fill empty plate seats (weight compensation) for Mehrkantfrässystem M275 |
|
Paul Horn LS275.MK13.M0 AS45 Indexable insert |
|
Paul Horn LS275.MK13.M0 TI25 Indexable insert |
|
Paul Horn LS310.3017.00 AS45 The indexable insert with a cutting width of 3 mm is suitable for separating milling up to 50 mm depth. |
|
Paul Horn LS310.3118.00 AS45 The indexable insert with a cutting width of 3,175 mm is suitable for separating milling up to 50 mm depth. |
|
Paul Horn LS310.4023.00 AS45 The indexable insert with a cutting width of 4 mm is suitable for separating milling up to 50 mm depth. |
|
Paul Horn LS310.4023.00 TF45 The indexable insert with a cutting width of 4 mm is suitable for separating milling up to 50 mm depth. |
|
Paul Horn LS310.4023.00 TN35 The indexable insert with a cutting width of 4 mm is suitable for separating milling up to 50 mm depth. |
|
Paul Horn LS310.5028.00 AS45 The indexable insert with a cutting width of 5 mm is suitable for separating milling up to 50 mm depth. |
|
Paul Horn LS310.5028.00 TF45 The indexable insert with a cutting width of 5 mm is suitable for separating milling up to 50 mm depth. |
|
Paul Horn LS310.5028.00 TN35 The indexable insert with a cutting width of 5 mm is suitable for separating milling up to 50 mm depth. |
|
Paul Horn LS312.0520.C2 TF46 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn LS312.0520.C2 TI25 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn LS312.0520.F2 TF46 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn LS312.0520.F2 TI25 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn LS312.0525.C2 TF46 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn LS312.0525.C2 TI25 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn LS312.0525.F2 TF46 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn LS312.0525.F2 TI25 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn LS312.0530.C2 TF46 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn LS312.0530.C2 TI25 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 5 mm, with geometry C and Abstechschräge 5 °, Model Links. |
|
Paul Horn LS316.0150.FY1 TI25 The indexable insert with a cutting width of 1.5 mm is suitable for penetration of outer contours with up to 8 mm depth. |
|
Paul Horn LS316.0200.52 AS45 The indexable insert with a cutting width of 2 mm is suitable for penetration of outer contours with up to 8 mm depth. |
|
Paul Horn LS316.0200.EN2 AS6G The indexable insert with a cutting width of 2 mm is suitable for penetration of outer contours with up to 8 mm depth. |
|
Paul Horn LS316.0200.FY2 TI25 The indexable insert with a cutting width of 2 mm is suitable for penetration of outer contours with up to 8 mm depth. |
|
Paul Horn LS316.0250.52 Indexable insert for grooving and turning at a cutting width of 2.5 mm, corner radius 0.2 mm and maximum piercing depth of 8 mm, suitable clamp holder H316, execution Links. |
|
Paul Horn LS316.0250.EN2 AS6G The indexable insert with a cutting width of 2.5 mm is suitable for penetration of outer contours with up to 8 mm depth. |
|
Paul Horn LS316.0250.FY2 TI25 The indexable insert with a cutting width of 2.5 mm is suitable for penetration of outer contours with up to 8 mm depth. |
|
Paul Horn LS316.0300.52 AS45 The indexable insert with a cutting width of 3 mm is suitable for penetration of outer contours with up to 8 mm depth. |
|
Paul Horn LS316.0300.EN2 AS6G The indexable insert with a cutting width of 3 mm is suitable for penetration of outer contours with up to 8 mm depth. |
|
Paul Horn LS316.0300.FY2 TI25 The indexable insert with a cutting width of 3 mm is suitable for penetration of outer contours with up to 8 mm depth. |
|
Paul Horn M101.0063.28.23.12 Trunk Leaf, cutting circle diameter: 63 mm, Type: neutral, system M101 |
|
Paul Horn M101.0063.28.23.14 Trunk Leaf, cutting circle diameter: 63 mm, Type: neutral, system M101 |
|
Paul Horn M101.0063.28.23.16 Trunk Leaf, cutting circle diameter: 63 mm, Width: 1.3 mm, Model: neutral, system M101 |
|
Paul Horn M101.0063.28.23.20 Trunk Leaf, cutting circle diameter: 63 mm, Width: 1.6 mm, Model: neutral, system M101 |
|
Paul Horn M101.0080.22.12 Routers disc to the slot milling with a cutting diameter of 80 mm, a slit width of 1.2 mm and maximum cutting depth of 20 mm, Type neutral. |
|
Paul Horn M101.0080.22.14 Routers disc to the slot milling with a cutting diameter of 80 mm, a slit width of 1.4 mm and maximum cutting depth of 20 mm, Type neutral. |
|
Paul Horn M101.0080.22.16 Routers disc to the slot milling with a cutting diameter of 80 mm, a slit width from 1.6 to 1.8 mm and maximum cutting depth of 20 mm, matching clamp holder H316, Neutral execution. |
|
Paul Horn M101.0080.22.20 Routers disc |
|
Paul Horn M101.0080.22.30 Routers disc |
|
Paul Horn M101.0080.22.40 Routers disc |
|
Paul Horn M101.0080.28.12 Main blade disc cutter type, cutting circle diameter: 80 mm, Width: 0.95 mm, max. |
|
Paul Horn M101.0080.28.14 Main blade disc cutter type, cutting circle diameter: 80 mm, Width: 1.15 mm, max. |
|
Paul Horn M101.0080.28.16 Main blade disc cutter type, cutting circle diameter: 80 mm, Width: 1.3 mm, max. |
|
Paul Horn M101.0080.28.20 Main blade disc cutter type, cutting circle diameter: 80 mm, Width: 1.6 mm, max. |
|
Paul Horn M101.0080.A16.12 Routers disc |
|
Paul Horn M101.0080.A16.14 Routers disc |
|
Paul Horn M101.0080.A16.16 Routers disc |
|
Paul Horn M101.0080.A16.20 Routers disc |
|
Paul Horn M101.0100.22.16 Routers disc |
|
Paul Horn M101.0100.22.20 Routers disc |
|
Paul Horn M101.0100.22.30 Routers disc |
|
Paul Horn M101.0100.22.40 Routers disc |
|
Paul Horn M101.0100.28.16 Main blade disc cutter type, cutting circle diameter: 100 mm, Width: 1.3 mm, max. |
|
Paul Horn M101.0100.28.20 Main blade disc cutter type, cutting circle diameter: 100 mm, Width: 1.6 mm, max. |
|
Paul Horn M101.0100.A22.16 Routers disc |
|
Paul Horn M101.0100.A22.20 Routers disc |
|
Paul Horn M101.0100.A22.30 Routers disc |
|
Paul Horn M101.0100.A22.40 Routers disc |
|
Paul Horn M101.0125.28.16 Trunk Leaf |
|
Paul Horn M101.0125.28.20 Trunk Leaf |
|
Paul Horn M101.0125.32.16 Routers disc |
|
Paul Horn M101.0125.32.20 Routers disc |
|
Paul Horn M101.0125.32.30 Routers disc |
|
Paul Horn M101.0125.32.40 Routers disc |
|
Paul Horn M101.0125.A32.16 Routers disc |
|
Paul Horn M101.0125.A32.20 Routers disc |
|
Paul Horn M101.0125.A32.30 Routers disc |
|
Paul Horn M101.0160.40.40 Routers disc |
|
Paul Horn M101.0160.A40.30 Routers disc |
|
Paul Horn M101.0200.40.40 Routers disc |
|
Paul Horn M101.0200.A40.40 Routers disc |
|
Paul Horn M101.063.D16.23.2.12A Routers disc |
|
Paul Horn M101.063.D16.23.2.14B Routers disc M101.063.D16.23.2.14A |
|
Paul Horn M101.063.D16.23.2.16A Routers disc as arbor with shaft to DIN1835-A |
|
Paul Horn M101.063.D16.23.2.20A Routers disc as arbor with shaft to DIN1835-A |
|
Paul Horn M101.063.D20.23.2.12B Routers disc |
|
Paul Horn M101.063.D20.23.2.14B Routers disc |
|
Paul Horn M101.063.D20.23.2.16B Routers disc as arbor with shaft to DIN1835-B |
|
Paul Horn M101.063.D20.23.2.20B Routers disc as arbor with shaft to DIN1835-B |
|
Paul Horn M101.063.D25.23.2.12B Routers disc |
|
Paul Horn M101.063.D25.23.2.14B Routers disc |
|
Paul Horn M101.063.D25.23.2.16B Routers disc |
|
Paul Horn M101.063.D25.23.2.20B Routers disc |
|
Paul Horn M116.0012.01B Cutter shank |
|
Paul Horn M116.0012.02B Cutter shank |
|
Paul Horn M116.0016.01B Cutter shank |
|
Paul Horn M116.0016.01E Cutter shank |
|
Paul Horn M116.0016.02B Cutter shank |
|
Paul Horn M116.0016.02E Cutter shank |
|
Paul Horn M116.0016.03B Cutter shank |
|
Paul Horn M117.1616.16 Toolholder |
|
Paul Horn M117.MD10.12.5.09 Cutter shank |
|
Paul Horn M117K.MD06.06.5.05 Cutter shank |
|
Paul Horn M117K.MD08.08.5.07 Cutter shank |
|
Paul Horn M117K.MD10.10.5.09 Cutter shank |
|
Paul Horn M117P.MD050.D20.M0 Cutter shank |
|
Paul Horn M117P.MD050.D20.X0 Cutter shank |
|
Paul Horn M117P.MD06.08.5.05 Cutter shank |
|
Paul Horn M117P.MD08.10.5.07 Cutter shank |
|
Paul Horn M117P.MD100.D32.M0 Cutter shank |
|
Paul Horn M117P.MD100.D32.X0 Cutter shank |
|
Paul Horn M117P.MD150.D32.M0 Cutter shank |
|
Paul Horn M117P.MD150.D32.X0 Cutter shank |
|
Paul Horn M117P.MD200.D32.M0 Cutter shank |
|
Paul Horn M117P.MD200.D32.X0 Cutter shank |
|
Paul Horn M117U.MD06.08.5.05 Cutter shank |
|
Paul Horn M117U.MD08.10.5.07 Cutter shank |
|
Paul Horn M274.0063.A22.7.10.IK Cutterhead type |
|
Paul Horn M274.0080.A27.7.13.IK Cutterhead type |
|
Paul Horn M275.0038.A16.05 Cutterhead |
|
Paul Horn M275.0048.A22.08 Cutterhead |
|
Paul Horn M275.0058.A27.10 Cutterhead |
|
Paul Horn M275.0078.A32.14 Cutterhead |
|
Paul Horn M275.031.D25.3.04A Cutter shank |
|
Paul Horn M275.031.M16.1.04 Einschraubfräser |
|
Paul Horn M275.036.M16.1.04 Einschraubfräser |
|
Paul Horn M301.A006.20.06 Whirling head |
|
Paul Horn M302.A012.40.06 Whirling head |
|
Paul Horn M302.AM12.40.06 Whirling head |
|
Paul Horn M302.AM12.T.40.06 Whirling head |
|
Paul Horn M302.C012.33.06 Whirling head |
|
Paul Horn M302.C012.40.06 Whirling head |
|
Paul Horn M302.DM11.0.40.06 Whirling head |
|
Paul Horn M302.T010.37.06 Whirling head |
|
Paul Horn M302.T025.54.06 Whirling head |
|
Paul Horn M302.W012.32.06 Whirling head |
|
Paul Horn M306.0012.01A Cutter shank |
|
Paul Horn M306.0012.01B Cutter shank |
|
Paul Horn M306.0012.01E Cutter shank |
|
Paul Horn M306.0012.02A Cutter shank |
|
Paul Horn M306.0012.02B Cutter shank |
|
Paul Horn M306.0012.02E Cutter shank |
|
Paul Horn M306.0012.03A Cutter shank |
|
Paul Horn M306.0012.03B Cutter shank |
|
Paul Horn M306.0012.03E Cutter shank |
|
Paul Horn M306.0707.03A Cutter shank |
|
Paul Horn M306.0712.02A Cutter shank |
|
Paul Horn M306.0712.02B Cutter shank |
|
Paul Horn M306.0712.02E Cutter shank |
|
Paul Horn M306.0716.01A Cutter shank |
|
Paul Horn M306.0716.01B Cutter shank |
|
Paul Horn M306.0716.01E Cutter shank |
|
Paul Horn M306.0716.02A Cutter shank |
|
Paul Horn M306.0716.02B Cutter shank |
|
Paul Horn M306.1010.03A Cutter shank |
|
Paul Horn M306.ER11.02 Cutter shank |
|
Paul Horn M306.M081.01 Einschraubfräser |
|
Paul Horn M306.ST10.01A Cutter shank |
|
Paul Horn M306.ST10.01B Cutter shank |
|
Paul Horn M306.ST12.01A Cutter shank |
|
Paul Horn M306.ST12.01B Cutter shank |
|
Paul Horn M308.0012.01A Cutter shank |
|
Paul Horn M308.0012.01B Cutter shank |
|
Paul Horn M308.0012.01E Cutter shank |
|
Paul Horn M308.0012.02A Cutter shank |
|
Paul Horn M308.0012.02B Cutter shank |
|
Paul Horn M308.0012.02E Cutter shank |
|
Paul Horn M308.0012.03A Cutter shank |
|
Paul Horn M308.0012.03B Cutter shank |
|
Paul Horn M308.0012.03E Cutter shank |
|
Paul Horn M308.0012.07A Cutter shank |
|
Paul Horn M308.1012.02A Cutter shank |
