|
Paul Horn DSTM.4.060.010.070 TS3K Micro cutters Torus DSTM.4.060.010.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.080.000.030 TS3K Micro cutters Torus DSTM.4.080.000.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.080.000.050 TS3K Micro cutters Torus DSTM.4.080.000.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.080.000.070 TS3K Micro cutters Torus DSTM.4.080.000.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.080.010.030 TS3K Micro cutters Torus DSTM.4.080.010.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.080.010.050 TS3K Micro cutters Torus DSTM.4.080.010.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.080.010.070 TS3K Micro cutters Torus DSTM.4.080.010.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.100.000.030 TS3K Micro cutters Torus DSTM.4.100.000.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.100.000.050 TS3K Micro cutters Torus DSTM.4.100.000.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.100.000.070 TS3K Micro cutters Torus DSTM.4.100.000.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.100.010.030 TS3K Micro cutters Torus DSTM.4.100.010.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.100.010.050 TS3K Micro cutters Torus DSTM.4.100.010.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.100.010.070 TS3K Micro cutters Torus DSTM.4.100.010.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.100.020.030 TS3K Micro cutters Torus DSTM.4.100.020.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.100.020.050 TS3K Micro cutters Torus DSTM.4.100.020.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.100.020.070 TS3K Micro cutters Torus DSTM.4.100.020.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.120.000.030 TS3K Micro cutters Torus DSTM.4.120.000.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.120.000.050 TS3K Micro cutters Torus DSTM.4.120.000.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.120.000.070 TS3K Micro cutters Torus DSTM.4.120.000.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.120.010.030 TS3K Micro cutters Torus DSTM.4.120.010.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.120.010.050 TS3K Micro cutters Torus DSTM.4.120.010.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.120.010.070 TS3K Micro cutters Torus DSTM.4.120.010.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.120.020.030 TS3K Micro cutters Torus DSTM.4.120.020.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.120.020.050 TS3K Micro cutters Torus DSTM.4.120.020.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.120.020.070 TS3K Micro cutters Torus DSTM.4.120.020.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.150.000.030 TS3K Micro cutters Torus DSTM.4.150.000.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.150.000.050 TS3K Micro cutters Torus DSTM.4.150.000.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.150.000.070 TS3K Micro cutters Torus DSTM.4.150.000.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.150.010.030 TS3K Micro cutters Torus DSTM.4.150.010.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.150.010.050 TS3K Micro cutters Torus DSTM.4.150.010.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.150.010.070 TS3K Micro cutters Torus DSTM.4.150.010.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.150.020.030 TS3K Micro cutters Torus DSTM.4.150.020.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.150.020.050 TS3K Micro cutters Torus DSTM.4.150.020.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.150.020.070 TS3K Micro cutters Torus DSTM.4.150.020.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.150.050.030 TS3K Micro cutters Torus DSTM.4.150.050.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.150.050.050 TS3K Micro cutters Torus DSTM.4.150.050.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.150.050.070 TS3K Micro cutters Torus DSTM.4.150.050.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.200.000.030 TS3K Micro cutters Torus DSTM.4.200.000.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.200.000.050 TS3K Micro cutters Torus DSTM.4.200.000.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.200.000.070 TS3K Micro cutters Torus DSTM.4.200.000.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.200.010.030 TS3K Micro cutters Torus DSTM.4.200.010.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.200.010.050 TS3K Micro cutters Torus DSTM.4.200.010.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.200.010.070 TS3K Micro cutters Torus DSTM.4.200.010.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.200.020.030 TS3K Micro cutters Torus DSTM.4.200.020.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.200.020.050 TS3K Micro cutters Torus DSTM.4.200.020.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.200.020.070 TS3K Micro cutters Torus DSTM.4.200.020.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.200.050.030 TS3K Micro cutters Torus DSTM.4.200.050.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.200.050.050 TS3K Micro cutters Torus DSTM.4.200.050.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.200.050.070 TS3K Micro cutters Torus DSTM.4.200.050.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.250.000.030 TS3K Micro cutters Torus DSTM.4.250.000.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.250.000.050 TS3K Micro cutters Torus DSTM.4.250.000.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.250.000.070 TS3K Micro cutters Torus DSTM.4.250.000.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.250.010.030 TS3K Micro cutters Torus DSTM.4.250.010.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.250.010.050 TS3K Micro cutters Torus DSTM.4.250.010.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.250.010.070 TS3K Micro cutters Torus DSTM.4.250.010.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.250.020.030 TS3K Micro cutters Torus DSTM.4.250.020.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.250.020.050 TS3K Micro cutters Torus DSTM.4.250.020.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.250.020.070 TS3K Micro cutters Torus DSTM.4.250.020.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.250.050.030 TS3K Micro cutters Torus DSTM.4.250.050.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.250.050.050 TS3K Micro cutters Torus DSTM.4.250.050.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.250.050.070 TS3K Micro cutters Torus DSTM.4.250.050.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.300.000.030 TS3K Micro cutters Torus DSTM.4.300.000.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.300.000.050 TS3K Micro cutters Torus DSTM.4.300.000.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.300.000.070 TS3K Micro cutters Torus DSTM.4.300.000.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.300.010.030 TS3K Micro cutters Torus DSTM.4.300.010.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.300.010.050 TS3K Micro cutters Torus DSTM.4.300.010.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.300.010.070 TS3K Micro cutters Torus DSTM.4.300.010.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.300.020.030 TS3K Micro cutters Torus DSTM.4.300.020.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.300.020.050 TS3K Micro cutters Torus DSTM.4.300.020.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.300.020.070 TS3K Micro cutters Torus DSTM.4.300.020.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.300.050.030 TS3K Micro cutters Torus DSTM.4.300.050.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.300.050.050 TS3K Micro cutters Torus DSTM.4.300.050.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.300.050.070 TS3K Micro cutters Torus DSTM.4.300.050.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.300.100.030 TS3K Micro cutters Torus DSTM.4.300.100.030, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.300.100.050 TS3K Micro cutters Torus DSTM.4.300.100.050, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTM.4.300.100.070 TS3K Micro cutters Torus DSTM.4.300.100.070, 4-edged, 30 В° helix angle, center cutting |
|
Paul Horn DSTMA.010.003.030 MG3K Torus for the machining of aluminum, corner radius 0.03mm, 2 blades with a diameter of 0.1 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.010.003.050 MG3K Torus for the machining of aluminum, corner radius 0.03mm, 2 blades with a diameter of 0.1 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.010.003.070 MG3K Torus for the machining of aluminum, corner radius 0.03mm, 2 blades with a diameter of 0.1 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.020.005.030 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 0.2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.020.005.050 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 0.2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.020.005.070 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 0.2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.030.005.030 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.030.005.050 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.030.005.070 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.050.005.030 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 0.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.050.005.050 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 0.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.050.005.070 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 0.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.050.010.030 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.050.010.050 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.050.010.070 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.060.005.030 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 0.6 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.060.005.050 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 0.6 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.060.005.070 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 0.6 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.060.010.030 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.060.010.050 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.060.010.070 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.080.005.030 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 0.8 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.080.005.050 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 0.8 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.080.005.070 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 0.8 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.080.010.030 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.080.010.050 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.080.010.070 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.100.005.030 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 1 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.100.005.050 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 1 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.100.005.070 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 1 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.100.010.030 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.100.010.050 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.100.010.070 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.120.005.030 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 1.2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.120.005.050 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 1.2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.120.005.070 MG3K Torus for the machining of aluminum, corner radius 0.05mm, 2 blades with a diameter of 1.2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.120.010.030 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.120.010.050 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.120.010.070 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.150.010.030 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.150.010.050 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.150.010.070 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.150.020.030 MG3K Torus for the machining of aluminum, corner radius 0.2 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.150.020.050 MG3K Torus for the machining of aluminum, corner radius 0.2 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.150.020.070 MG3K Torus for the machining of aluminum, corner radius 0.2 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.150.050.030 MG3K Torus for the machining of aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.150.050.050 MG3K Torus for the machining of aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.150.050.070 MG3K Torus for the machining of aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.200.010.030 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.200.010.050 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.200.010.070 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.200.020.030 MG3K Torus for the machining of aluminum, corner radius 0.2 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.200.020.050 MG3K Torus for the machining of aluminum, corner radius 0.2 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.200.020.070 MG3K Torus for the machining of aluminum, corner radius 0.2 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.200.050.030 MG3K Torus for the machining of aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.200.050.050 MG3K Torus for the machining of aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.200.050.070 MG3K Torus for the machining of aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.250.010.030 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.250.010.050 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.250.010.070 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.250.020.030 MG3K Torus for the machining of aluminum, corner radius 0.2 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.250.020.050 MG3K Torus for the machining of aluminum, corner radius 0.2 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.250.020.070 MG3K Torus for the machining of aluminum, corner radius 0.2 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.250.050.030 MG3K Torus for the machining of aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.250.050.050 MG3K Torus for the machining of aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.250.050.070 MG3K Torus for the machining of aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.300.010.030 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.300.010.050 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.300.010.070 MG3K Torus for the machining of aluminum, corner radius 0.1 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.300.020.030 MG3K Torus for the machining of aluminum, corner radius 0.2 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.300.020.050 MG3K Torus for the machining of aluminum, corner radius 0.2 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.300.020.070 MG3K Torus for the machining of aluminum, corner radius 0.2 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.300.050.030 MG3K Torus for the machining of aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.300.050.050 MG3K Torus for the machining of aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.300.050.070 MG3K Torus for the machining of aluminum, corner radius 0.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.300.100.030 MG3K Torus for the machining of aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.300.100.050 MG3K Torus for the machining of aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMA.300.100.070 MG3K Torus for the machining of aluminum, corner radius 1 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm, center cutting. |
|
Paul Horn DSTMH.010.000.015 TS3E End mills as micro cutters for hard machining, 2 blades with a diameter of 0.1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.010.000.030 TS3E End mills as micro cutters for hard machining, 2 blades with a diameter of 0.1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.020.000.015 TS3E End mills as micro cutters for hard machining, 2 blades with a diameter of 0.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.020.000.030 TS3E End mills as micro cutters for hard machining, 2 blades with a diameter of 0.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.020.000.050 TS3E End mills as micro cutters for hard machining, 2 blades with a diameter of 0.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.030.005.015 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.030.005.030 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.030.005.050 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.040.005.015 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.4 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.040.005.030 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.4 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.040.005.050 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.4 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.050.005.015 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.050.005.030 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.050.005.050 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.050.005.070 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.050.010.015 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.050.010.030 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.050.010.050 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.050.010.070 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 0.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.060.005.015 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.060.005.030 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.060.005.050 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.060.005.070 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.060.010.015 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.060.010.030 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.060.010.050 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.060.010.070 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 0.6 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.080.005.015 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.080.005.030 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.080.005.050 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.080.005.070 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.080.010.015 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.080.010.030 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.080.010.050 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.080.010.070 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 0.8 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.100.005.015 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.100.005.030 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.100.005.050 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.100.005.070 TS3E End mills as micro cutters for hard machining with corner radius 0.05mm, 2 blades with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.100.010.015 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.100.010.030 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.100.010.050 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.100.010.070 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 1 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.120.010.015 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.120.010.030 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.120.010.050 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.120.010.070 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 1.2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.150.010.015 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.150.010.030 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.150.010.050 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.150.010.070 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.150.020.015 TS3E End mills as micro cutters for hard machining with corner radius 0.2 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.150.020.030 TS3E End mills as micro cutters for hard machining with corner radius 0.2 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.150.020.050 TS3E End mills as micro cutters for hard machining with corner radius 0.2 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.150.020.070 TS3E End mills as micro cutters for hard machining with corner radius 0.2 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.150.050.015 TS3E End mills as micro cutters for hard machining with corner radius 0.5 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.150.050.030 TS3E End mills as micro cutters for hard machining with corner radius 0.5 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.150.050.050 TS3E End mills as micro cutters for hard machining with corner radius 0.5 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.150.050.070 TS3E End mills as micro cutters for hard machining with corner radius 0.5 mm, 2 cutting edges with a diameter of 1.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.200.010.015 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.200.010.030 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.200.010.050 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.200.010.070 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.200.020.015 TS3E End mills as micro cutters for hard machining with corner radius 0.2 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.200.020.030 TS3E End mills as micro cutters for hard machining with corner radius 0.2 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.200.020.050 TS3E End mills as micro cutters for hard machining with corner radius 0.2 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.200.020.070 TS3E End mills as micro cutters for hard machining with corner radius 0.2 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.200.050.015 TS3E End mills as micro cutters for hard machining with corner radius 0.5 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.200.050.030 TS3E End mills as micro cutters for hard machining with corner radius 0.5 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.200.050.050 TS3E End mills as micro cutters for hard machining with corner radius 0.5 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.200.050.070 TS3E End mills as micro cutters for hard machining with corner radius 0.5 mm, 2 cutting edges with a diameter of 2 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.250.010.015 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.250.010.030 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.250.010.050 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.250.010.070 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.250.020.015 TS3E End mills as micro cutters for hard machining with corner radius 0.2 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.250.020.030 TS3E End mills as micro cutters for hard machining with corner radius 0.2 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.250.020.050 TS3E End mills as micro cutters for hard machining with corner radius 0.2 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.250.020.070 TS3E End mills as micro cutters for hard machining with corner radius 0.2 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.250.050.015 TS3E End mills as micro cutters for hard machining with corner radius 0.5 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.250.050.030 TS3E End mills as micro cutters for hard machining with corner radius 0.5 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.250.050.050 TS3E End mills as micro cutters for hard machining with corner radius 0.5 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.250.050.070 TS3E End mills as micro cutters for hard machining with corner radius 0.5 mm, 2 cutting edges with a diameter of 2.5 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.300.010.015 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.300.010.030 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.300.010.050 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.300.010.070 TS3E End mills as micro cutters for hard machining with corner radius 0.1 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.300.020.015 TS3E End mills as micro cutters for hard machining with corner radius 0.2 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.300.020.030 TS3E End mills as micro cutters for hard machining with corner radius 0.2 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.300.020.050 TS3E End mills as micro cutters for hard machining with corner radius 0.2 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.300.020.070 TS3E End mills as micro cutters for hard machining with corner radius 0.2 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.300.050.015 TS3E End mills as micro cutters for hard machining with corner radius 0.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.300.050.030 TS3E End mills as micro cutters for hard machining with corner radius 0.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.300.050.050 TS3E End mills as micro cutters for hard machining with corner radius 0.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.300.050.070 TS3E End mills as micro cutters for hard machining with corner radius 0.5 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.300.100.015 TS3E End mills as micro cutters for hard machining with corner radius 1 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.300.100.030 TS3E End mills as micro cutters for hard machining with corner radius 1 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.300.100.050 TS3E End mills as micro cutters for hard machining with corner radius 1 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSTMH.300.100.070 TS3E End mills as micro cutters for hard machining with corner radius 1 mm, 2 cutting edges with a diameter of 3 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSUD.4.08.15.44.08 HD05 End mills CVD-D equipped for processing z. B. Kohlefaserwerstoffen, 4-edged, with a diameter of 8 mm and a shaft diameter of 8 mm, pulling and pushing. |
|
Paul Horn DSUD.4.08.20.33.08 HD05 End mills CVD-D equipped for processing z. B. Kohlefaserwerstoffen, 4-edged, with a diameter of 8 mm and a shaft diameter of 8 mm, pulling and pushing. |
|
Paul Horn DSUD.4.08.24.22.08 HD05 End mills CVD-D equipped for processing z. B. Kohlefaserwerstoffen, 4-edged, with a diameter of 8 mm and a shaft diameter of 8 mm, pulling and pushing. |
|
Paul Horn DSUD.4.10.15.44.10 HD05 End mills CVD-D equipped for processing z. B. Kohlefaserwerstoffen, 4-edged, with a diameter of 10 mm and a shaft diameter of 10 mm, drawing and sliding. |
|
Paul Horn DSUD.4.10.20.33.10 HD05 End mills CVD-D equipped for processing z. B. Kohlefaserwerstoffen, 4-edged, with a diameter of 10 mm and a shaft diameter of 10 mm, drawing and sliding. |
|
Paul Horn DSUD.4.10.24.22.10 HD05 End mills CVD-D equipped for processing z. B. Kohlefaserwerstoffen, 4-edged, with a diameter of 10 mm and a shaft diameter of 10 mm, drawing and sliding. |
|
Paul Horn DSUD.4.12.15.44.12 HD05 End mills CVD-D equipped for processing z. B. Kohlefaserwerstoffen, 4-edged, with a diameter of 12 mm and a shaft diameter of 12 mm, drawing and sliding. |
|
Paul Horn DSUD.4.12.20.44.12 HD05 End mills CVD-D equipped for processing z. B. Kohlefaserwerstoffen, 4-edged, with a diameter of 12 mm and a shaft diameter of 12 mm, drawing and sliding. |
|
Paul Horn DSUD.4.12.24.33.12 HD05 End mills CVD-D equipped for processing z. B. Kohlefaserwerstoffen, 4-edged, with a diameter of 12 mm and a shaft diameter of 12 mm, drawing and sliding. |
|
Paul Horn DSUD.4.16.15.44.16 HD05 End mills CVD-D equipped for processing z. B. Kohlefaserwerstoffen, 4-edged, with a diameter of 16 mm and a shaft diameter of 16 mm, drawing and sliding. |
|
Paul Horn DSUD.4.16.20.44.16 HD05 End mills CVD-D equipped for processing z. B. Kohlefaserwerstoffen, 4-edged, with a diameter of 16 mm and a shaft diameter of 16 mm, drawing and sliding. |
|
Paul Horn DSUD.4.16.24.44.16 HD05 End mills CVD-D equipped for processing z. B. Kohlefaserwerstoffen, 4-edged, with a diameter of 16 mm and a shaft diameter of 16 mm, drawing and sliding. |
|
Paul Horn DSVG.X.04.0.59.04 CD5K End mills as Roughing for machining graphite, 4-edged, with a diameter of 4 mm and a shaft diameter of 4 mm. |
|
Paul Horn DSVG.X.06.0.77.06 CD5K End mills as Roughing for machining graphite, 6-edged with a diameter of 6 mm and a shaft diameter of 6 mm. |
|
Paul Horn DSVG.X.08.0.77.08 CD5K End mills as Roughing for machining graphite, 8-edged with a diameter of 8 mm and a shaft diameter of 8 mm. |
|
Paul Horn DSVG.X.10.0.77.10 CD5K End mills as Roughing for machining graphite, 10 flutes with a diameter of 10 mm and a shaft diameter of 10 mm. |
|
Paul Horn DSVG.X.12.0.88.12 CD5K End mills as Roughing for machining graphite, 12 flutes with a diameter of 12 mm and a shaft diameter of 12 mm. |
|
Paul Horn DSW15K Interchangeable Blade for Allen screws, suitable for torque screwdrivers D041VL, D14ZBK, D15VL and D28VL |
|
Paul Horn DSW20K Interchangeable Blade for Allen screws, suitable for torque screwdrivers D041VL, D14ZBK, D15VL and D28VL |
|
Paul Horn DSW25K Interchangeable Blade for Allen screws, suitable for torque screwdrivers D041VL, D14ZBK, D15VL and D28VL |
|
Paul Horn DSW30K Interchangeable Blade for Allen screws, suitable for torque screwdrivers D041VL, D14ZBK, D15VL and D28VL |
|
Paul Horn DSW40K Interchangeable Blade for Allen screws, suitable for torque screwdrivers D041VL, D14ZBK, D15VL and D28VL |
|
Paul Horn DT10PK Interchangeable blade for Torx PLUSВ® screws, suitable for torque screwdrivers D041VL, D14ZBK, D15VL and D28VL |
|
Paul Horn DT15PK Interchangeable blade for Torx PLUSВ® screws, suitable for torque screwdrivers D041VL, D14ZBK, D15VL and D28VL |
|
Paul Horn DT15PQ Interchangeable blade for Torx PlusВ® screws DT20PQ, suitable for the torque screwdriver D515QL |
|
Paul Horn DT20PK Interchangeable blade for Torx PLUSВ® screws, suitable for torque screwdrivers D041VL, D14ZBK, D15VL and D28VL |
|
Paul Horn DT20PQ Interchangeable blade for Torx PlusВ® screws, suitable for the torque screwdriver D515QL |
|
Paul Horn DT25PK Interchangeable blade for Torx PLUSВ® screws, suitable for torque screwdrivers D041VL, D14ZBK, D15VL and D28VL |
|
Paul Horn DT25PQ Interchangeable blade for Torx PlusВ® screws, suitable for the torque screwdriver D515QL |
|
Paul Horn DT30PQ Interchangeable blade for Torx PlusВ® screws, suitable for the torque screwdriver D515QL |
|
Paul Horn DT6PK Interchangeable blade for Torx PLUSВ® screws, suitable for torque screwdrivers D041VL, D14ZBK, D15VL and D28VL |
|
Paul Horn DT7PK Interchangeable blade for Torx PLUSВ® screws, suitable for torque screwdrivers D041VL, D14ZBK, D15VL and D28VL |
|
Paul Horn DT8PK Interchangeable blade for Torx PLUSВ® screws, suitable for torque screwdrivers D041VL, D14ZBK, D15VL and D28VL |
|
Paul Horn DT9PK Interchangeable blade for Torx PLUSВ® screws, suitable for torque screwdrivers D041VL, D14ZBK, D15VL and D28VL |
|
Paul Horn DTM.CX09.040.A16.04 Cutterhead as arbor suitable for milling arbor 16 mm, are 4 cutting with a cutting diameter of 40 mm in the axial runout in the range of 0.1 mm to Erziehlung optimum surfaces adjustable. |
|
Paul Horn DTM.CX09.050.A22.05 Cutterhead as arbor suitable for milling arbor 22 mm, which are 5 cut in a cutting diameter of 50 mm in the axial runout in the range of 0.1 mm to Erziehlung optimum surfaces adjustable. |
|
Paul Horn DTM.CX09.063.A22.06 Cutterhead as arbor suitable for milling arbor 22 mm, which are 6 cutting with a cutting diameter of 63 mm in the axial runout in the range of 0.1 mm to Erziehlung optimum surfaces adjustable. |
|
Paul Horn DTM.CX09.080.A27.06 Cutterhead as arbor suitable for milling arbor 27 mm, which are 6 cutting with a cutting diameter of 80 mm in the axial runout in the range of 0.1 mm to Erziehlung optimum surfaces adjustable. |
|
Paul Horn DTM.CX09.100.A32.07 Cutterhead as arbor suitable for milling arbor 32 mm, which are 7 cutting with a cutting diameter of 100 mm in the axial runout in the range of 0.1 mm to Erziehlung optimum surfaces adjustable. |
|
Paul Horn DTM.CX09.125.A40.08 Cutterhead as arbor suitable for milling arbor 40 mm, which are 8 cutting with a cutting diameter of 125 mm in the axial runout in the range of 0.1 mm to Erziehlung optimum surfaces adjustable. |
|
Paul Horn DTS.CX09.11.H0 PD75 Insert DTS.CX09.11.H0 Pd75 stocked as wiper insert with PCD for machining eg., Aluminum, corner radius 0.4 mm, suitable for knife head DTM .... |
|
Paul Horn DTS.CX09.33.H0 HD08 Insert stocked as wiper insert with CVD-D for processing z. B. Aluminium, corner radius 0.4 mm, suitable for knife head DTM .... |
|
Paul Horn DTS.CX09.66.H0 HD08 Insert stocked as wiper insert with CVD-D for processing z. B. Aluminium, 0.45x45 Eckfase В°, matching cutterhead DTM .... |
|
Paul Horn Einstellwerkzeug ED 28 VL Torque adjustment tool ED28VL match the setting for Torque screwdrivers D28VL |
|
Paul Horn Einstellwerkzeug ED 515 QL Torque adjusting ED 515 QL to match the setting for Torque screwdrivers D515QL |
|
Paul Horn ER11.6499 Locknut fit chuck for clamping cutter shank M306.ER, M308.ER and M311.ER |
|
Paul Horn ER16.6499 Locknut fit chuck for clamping cutter shank M306.ER, M308.ER and M311.ER |
|
Paul Horn ER20.6499 Locknut fit chuck for clamping cutter shank M306.ER, M308.ER and M311.ER |
|
Paul Horn ER25.6499 Locknut fit chuck for clamping cutter shank M306.ER, M308.ER and M311.ER |
|
Paul Horn ER32.6499 Locknut fit chuck for clamping cutter shank M306.ER, M308.ER and M311.ER |
|
Paul Horn Exzenterbolzen eccentric 020.1208.4783 |
|
Paul Horn F050.G87297.02 Fine boring head |
|
Paul Horn F050.K4988.01 Fine boring head |
|
Paul Horn G010060 Basic holder Graf machines specifically for Citizen, Shaft diameter 25.40 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G010100 Basic holder Graf machines specifically for Citizen, Shaft diameter 25.40 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G016021 Basic holder Graf machines specifically for Star, shaft diameter 16.00mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G016040 Basic holder Graf machines specifically for Traub / Manurhin, shaft diameter 16.00mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G020030 Basic holder Graf machines specifically for Citizen, Shaft diameter 20.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G020040 Basic holder Graf machines specifically for Hanwha, Shaft diameter 20.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G020100 Basic holder Graf machinery specific to Tornos, Shaft diameter 20.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G020150 Basic holder Graf machines specifically for Manurhin / Tornos, Shaft diameter 20.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G022023 Basic holder Graf machines specifically for Star, Shaft diameter 22.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G022025SR16/20R Basic holder Graf G022025SR16 / 20R machines specifically for Star, Shaft diameter 22.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G022030 Basic holder Graf machines specifically for Star, Shaft diameter 22.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G022030SR32 Basic holder Graf machines specifically for Star, Shaft diameter 22.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G022070 Basic holder Graf machines specifically for Star, Shaft diameter 22.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G025060 Basic holder Graf machines specifically for Hanwha, Shaft diameter 25.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G025070 Basic holder Graf machines specifically for Manurhin / Tornos, Shaft diameter 25.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G025100 Basic holder Graf machines specifically for Manurhin / Tornos, Shaft diameter 25.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G025160 Basic holder Graf machines specifically for Manurhin / Tornos, Shaft diameter 25.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G028006 Basic holder Graf machines specifically for Hanwha, Shaft diameter 28.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G028080 Basic holder Graf machines specifically for Traub, Shaft diameter 28.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G030045 Basic holder Graf machines specifically for Maier, Shaft diameter 30.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G033040 Basic holder Graf machines specifically for Hanwha, Shaft diameter 33.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G034020 Basic holder Graf machines specifically for Maier, Shaft diameter 34.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G034040 Basic holder Graf machines specifically for Citizen, shank diameter 5.19 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G034044 Basic holder Graf machines specifically for Maier / Hanwha, Shaft diameter 34.00 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G034050 Basic holder Graf machines specifically for Citizen, shank diameter 5.19 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn G034120 Basic holder Graf machines specifically for Citizen, shank diameter 5.19 mm, fits to adjustable holder Graf Type N and Horn type BKT ... ... |
|
Paul Horn GZ79.1065.16 Double collet holder with internal coolant supply, clamping shank diameter 25.40 mm, collet size ER16. |
|
Paul Horn GZ79.2065.16 Double collet holder with internal coolant supply, clamping shank diameter 20.00 mm, collet size ER16. |
|
Paul Horn GZ79.22100.16 Double collet holder with internal coolant supply, clamping shank diameter 22.00 mm, collet size ER16. |
|
Paul Horn GZ79.2262.16 Double collet holder with internal coolant supply, clamping shank diameter 22.00 mm, collet size ER16. |
|
Paul Horn GZ79.2580.16 Double collet holder with internal coolant supply, clamping shank diameter 25.00 mm, collet size ER16. |
|
Paul Horn GZ79.3470.16 Double collet holder with internal coolant supply, clamping shank diameter 1.19 mm, collet size ER16. |
|
Paul Horn H100.2601.01 Toolholder for parting with cutting plate S100 to diameter 50.00 mm, height 26.00 mm, self-locking, with 2 board seats size 01, width mm 1:50. |
|
Paul Horn H100.2602.02 Toolholder for parting with cutting plate S100 to diameter 75.00 mm, height 26.00 mm, self-locking, with 2 board seats size 02, width 1.90 mm. |
|
Paul Horn H100.2603.01 Toolholder for parting with cutting plate S100 to diameter 42.00 mm, height 26.00 mm, self-locking, with 2 board seats size 01, width mm 1:50. |
|
Paul Horn H100.2603.03 Toolholder for parting with cutting plate S100 to diameter 75.00 mm, height 26.00 mm, self-locking, with 2 board seats size 03, width 30.2 mm. |
|
Paul Horn H100.2604.04 Toolholder for parting with cutting plate S100 to diameter 80.00 mm, height 26.00 mm, self-locking, with 2 board seats size 04, width 10.3 mm. |
|
Paul Horn H100.3201.01 Toolholder for parting with cutting plate S100 to diameter 50.00 mm, height 32.00 mm, self-locking, with 2 board seats size 01, width mm 1:50. |
|
Paul Horn H100.3202.02 Toolholder for parting with cutting plate S100 to diameter 100.00 mm, height 32.00 mm, self-locking, with 2 board seats size 02, width 1.90 mm. |
|
Paul Horn H100.3203.01 Toolholder for parting with cutting plate S100 to diameter 50.00 mm, height 32.00 mm, self-locking, with 2 board seats size 01, width mm 1:50. |
|
Paul Horn H100.3203.02 Toolholder for parting with cutting plate S100 to diameter 50.00 mm, height 32.00 mm, self-locking, with 2 board seats size 02, width 1.90 mm. |
|
Paul Horn H100.3203.03 Toolholder for parting with cutting plate S100 to diameter 100.00 mm, height 32.00 mm, self-locking, with 2 board seats size 03, width 30.2 mm. |
|
Paul Horn H100.3204.04 Toolholder for parting with cutting plate S100 to diameter 110.00 mm, height 32.00 mm, self-locking, with 2 board seats size 04, width 10.3 mm. |
|
Paul Horn H100.3205.05 Toolholder for parting with cutting plate S100 to diameter 110.00 mm, height 32.00 mm, self-locking, with 2 board seats size 05, width 3.90 mm. |
|
Paul Horn H11 43 01 054 Basic recording URMA for direct recording of Einbauhalter BKT105.U90K.01 and BKT356.U90K.05, with terminal SK40 / B. |
|
Paul Horn H11 43 03 052 Basic recording URMA for direct recording of Einbauhalter BKT105.U90K.01 and BKT356.U90K.05, with terminal SK40 / B. |
|
Paul Horn H117.1010.02.10 Toolholder with a shaft height h = 10 mm and b = 10 mm shank width is suitable for receiving profilierbarer insert S117.0010.02.00. |
|
Paul Horn H117.1010.10 Toolholder with a shaft height h = 10 mm and b = 10 mm shank width is suitable for receiving profilierbarer insert S117.0010.00. |
|
Paul Horn H117.1212.02.10 Toolholder with a shaft height h = 12 mm and shank width b = 12 mm is suitable for receiving profilierbarer insert S117.0010.02.00. |
|
Paul Horn H117.1212.02.12 Toolholder with a shaft height h = 12 mm and shank width b = 12 mm is suitable for receiving profilierbarer insert S117.0012.02.00. |
|
Paul Horn H117.1212.10 Toolholder with a shaft height h = 12 mm and shank width b = 12 mm is suitable for receiving profilierbarer insert S117.0010.00. |
|
Paul Horn H117.1212.12 Toolholder with a shaft height h = 12 mm and shank width b = 12 mm is suitable for receiving profilierbarer insert S117.0012.00. |
|
Paul Horn H117.1414.12 Toolholder with a shaft height h = 14 mm and b = 14 mm shank width is suitable for receiving profilierbarer insert S117.0012.00. |
|
Paul Horn H117.1414.16 Toolholder with a shaft height h = 14 mm and b = 14 mm shank width is suitable for receiving profilierbarer insert S117.0014 / 16:00. |
|
Paul Horn H117.1612.12 Toolholder with a shaft height h = 16 mm and shank width b = 12 mm is suitable for receiving profilierbarer insert S117.0012.00. |
|
Paul Horn H117.1616.02.10 Toolholder with a shaft height h = 16 mm and shank width b = 16 mm is suitable for receiving profilierbarer insert S117.0010.02.00. |
|
Paul Horn H117.1616.02.12 Toolholder with a shaft height h = 16 mm and shank width b = 16 mm is suitable for receiving profilierbarer insert S117.0012.02.00. |
|
Paul Horn H117.1616.02.16 Toolholder with a shaft height h = 16 mm and shank width b = 16 mm is suitable for receiving profilierbarer insert S117.0016.02.00. |
|
Paul Horn H117.1616.02.20 Toolholder with a shaft height h = 16 mm and shank width b = 16 mm is suitable for receiving profilierbarer insert S117.0020.02.00. |
|
Paul Horn H117.1616.10 Toolholder with a shaft height h = 16 mm and shank width b = 16 mm is suitable for receiving profilierbarer insert S117.0010.00. |
|
Paul Horn H117.1616.12 Toolholder with a shaft height h = 16 mm and shank width b = 16 mm is suitable for receiving profilierbarer insert S117.0012.00. |
|
Paul Horn H117.1616.16 Toolholder with a shaft height h = 16 mm and shank width b = 16 mm is suitable for receiving profilierbarer insert S117.0014 / 16:00. |
|
Paul Horn H117.1616.20 Toolholder with a shaft height h = 16 mm and shank width b = 16 mm is suitable for receiving profilierbarer insert S117.0018 / 20:00. |
|
Paul Horn H117.2020.02.12 Toolholder with a shaft height h = 20 mm and b = 20 mm shank width is suitable for receiving profilierbarer insert S117.0012.02.00. |
|
Paul Horn H117.2020.02.16 Toolholder with a shaft height h = 20 mm and b = 20 mm shank width is suitable for receiving profilierbarer insert S117.0016.02.00. |
|
Paul Horn H117.2020.02.20 Toolholder with a shaft height h = 20 mm and b = 20 mm shank width is suitable for receiving profilierbarer insert S117.0020.02.00. |
|
Paul Horn H117.2020.02.26 Toolholder with a shaft height h = 20 mm and b = 20 mm shank width is suitable for receiving profilierbarer insert S117.0026.02.00. |
|
Paul Horn H117.2020.12 Toolholder with a shaft height h = 20 mm and b = 20 mm shank width is suitable for receiving profilierbarer insert S117.0012.00. |
|
Paul Horn H117.2020.16 Toolholder with a shaft height h = 20 mm and b = 20 mm shank width is suitable for receiving profilierbarer insert S117.0014 / 16:00. |
|
Paul Horn H117.2020.20 Toolholder with a shaft height h = 20 mm and b = 20 mm shank width is suitable for receiving profilierbarer insert S117.0018 / 20:00. |
|
Paul Horn H117.2020.26 Toolholder with a shaft height h = 20 mm and b = 20 mm shank width is suitable for receiving profilierbarer insert S117.0026.00. |
|
Paul Horn H117.2020.32 Toolholder with a shaft height h = 20 mm and b = 20 mm shank width is suitable for receiving profilierbarer insert S117.0032.00. |
|
Paul Horn H117.2525.02.20 Toolholder with a shaft height h = 25 mm and shank width b = 25 mm is suitable for receiving profilierbarer insert S117.0020.02.00. |
|
Paul Horn H117.2525.02.26 Toolholder with a shaft height h = 25 mm and shank width b = 25 mm is suitable for receiving profilierbarer insert S117.0026.02.00. |
|
Paul Horn H117.2525.16 Toolholder with a shaft height h = 25 mm and shank width b = 25 mm is suitable for receiving profilierbarer insert S117.0014 / 16.00. |
|
Paul Horn H117.2525.20 Toolholder with a shaft height h = 25 mm and shank width b = 25 mm is suitable for receiving profilierbarer insert S117.0018 / 20:00. |
|
Paul Horn H117.2525.26 Toolholder with a shaft height h = 25 mm and shank width b = 25 mm is suitable for receiving profilierbarer insert S117.0026.00. |
|
Paul Horn H117.2525.32 Toolholder with a shaft height h = 25 mm and shank width b = 25 mm is suitable for receiving profilierbarer insert S117.0032.00. |
|
Paul Horn H117.2525.45 Toolholder with a shaft height h = 25 mm and shank width b = 25 mm is suitable for receiving profilierbarer insert S117.0045.00. |
|
Paul Horn H117.3232.45 Toolholder with a shaft height h = 32 mm and b = 32 mm shank width is suitable for receiving profilierbarer insert S117.0045.00. |
|
Paul Horn H117.AW20.12 Toolholder after clamping system AWN with a clamping height h = 36 mm and cutting width b = 20 mm is suitable for receiving profilierbarer insert S117.0012.00. |
|
Paul Horn H117.AW28.10 Toolholder after clamping system AWN with a clamping height h = 36 mm and cutting width b = 28 mm is suitable for receiving profilierbarer insert S117.0010.00. |
|
Paul Horn H117.AW28.16 Toolholder after clamping system AWN with a clamping height h = 36 mm and cutting width b = 28 mm is suitable for receiving profilierbarer insert S117.0014 / 16:00. |
|
Paul Horn H117.AW28.20 Toolholder after clamping system AWN with a clamping height h = 36 mm and cutting width b = 28 mm is suitable for receiving profilierbarer insert S117.0018 / 20:00. |
|
Paul Horn H117.AW28.26 Toolholder after clamping system AWN with a clamping height h = 36 mm and cutting width b = 28 mm is suitable for receiving profilierbarer insert S117.0026.00. |
|
Paul Horn H117.AW28.32 Toolholder after clamping system AWN with a clamping height h = 36 mm and cutting width b = 28 mm is suitable for receiving profilierbarer insert S117.0032.00. |
|
Paul Horn H117.AW40.45 Tool holders type |
|
Paul Horn H117.MD10.00.5.10 Toolholder with a shaft height h = 10 mm and b = 10 mm shank width is suitable for receiving stocked with monocrystalline diamond cutting disc on request for polish turning. |
|
Paul Horn H224.2602.02 Toolholder as Abstechschwert, maximum digging depth is 18.00 mm, self-locking, with a clamping range from 2.4 to 2.8 mm, sword height is 26.00 mm. |
|
Paul Horn H224.2603.03 Toolholder as Abstechschwert, maximum digging depth is 18.00 mm, self-locking, with a clamping range from 2.8 to 3.7 mm, sword height is 26.00 mm. |
|
Paul Horn H224.3203.03 Toolholder as Abstechschwert, maximum digging depth is 18.00 mm, self-locking, with a clamping range from 2.8 to 3.7 mm, sword height is 32.00 mm. |
|
Paul Horn H956.0104.01 Recording match the height-adjustable lancing system 956 for multi-spindle SchГјtte SF26 / 32/42 / 51st |
|
Paul Horn H956.0201.01 Recording match the height-adjustable lancing system 956 for multi-spindle Index MS16 / 22nd |
|
Paul Horn H956.0202.01 Recording match the height-adjustable lancing system 956 for multi-spindle Index MS32 / 40th |
|
Paul Horn H956.0203.01 Recording match the height-adjustable lancing system 956 for multi-spindle Index MS52 / 67 standards. |
|
Paul Horn H956.0301.01 Recording match the height-adjustable lancing system 956 for multi-spindle Gildemeister MSL42 / 60th |
|
Paul Horn HCC.0050.05.01.20 MG12 The blade with a cutting width of 0.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0050.05.01.20 TH35 The blade with a cutting width of 0.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0050.05.01.20 TN35 The blade with a cutting width of 0.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0100.12.05.20 MG12 The blade with a cutting width of 1 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0100.12.05.20 TH35 The blade with a cutting width of 1 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0100.12.05.20 TN35 The blade with a cutting width of 1 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0100.17.12.20 MG12 The blade with a cutting width of 1 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0100.17.12.20 TH35 The blade with a cutting width of 1 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0100.17.12.20 TN35 The blade with a cutting width of 1 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0130.17.12.20 MG12 The blade with a cutting width of 1.3 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0130.17.12.20 TH35 The blade with a cutting width of 1.3 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0130.17.12.20 TN35 The blade with a cutting width of 1.3 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0150.17.12.20 MG12 The blade with a cutting width of 1.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0150.17.12.20 TH35 The blade with a cutting width of 1.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0150.17.12.20 TN35 The blade with a cutting width of 1.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0150.17.12.A0 MG12 The blade with a cutting width of 1.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0150.17.12.A0 TH35 The blade with a cutting width of 1.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0150.17.12.A0 TN35 The blade with a cutting width of 1.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0160.12.10.20 MG12 The blade with a cutting width of 1.6 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0160.12.10.20 TH35 The blade with a cutting width of 1.6 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0160.12.10.20 TN35 The blade with a cutting width of 1.6 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0160.12.10.A0 MG12 The blade with a cutting width of 1.6 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0160.12.10.A0 TH35 The blade with a cutting width of 1.6 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0160.12.10.A0 TN35 The blade with a cutting width of 1.6 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0160.17.12.20 MG12 The blade with a cutting width of 1.6 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0160.17.12.20 TH35 The blade with a cutting width of 1.6 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0160.17.12.20 TN35 The blade with a cutting width of 1.6 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0160.17.12.A0 MG12 The blade with a cutting width of 1.6 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0160.17.12.A0 TH35 The blade with a cutting width of 1.6 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0160.17.12.A0 TN35 The blade with a cutting width of 1.6 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0200.12.10.20 MG12 The blade with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0200.12.10.20 TH35 The blade with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0200.12.10.20 TN35 The blade with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0200.12.10.A0 MG12 The blade with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0200.12.10.A0 TH35 The blade with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0200.12.10.A0 TN35 The blade with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0200.17.12.20 MG12 The blade with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0200.17.12.20 TH35 The blade with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0200.17.12.20 TN35 The blade with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0200.17.12.A0 MG12 The blade with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0200.17.12.A0 TH35 The blade with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0200.17.12.A0 TN35 The blade with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0250.12.10.20 MG12 The blade with a cutting width of 2.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0250.12.10.20 TH35 The blade with a cutting width of 2.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0250.12.10.20 TN35 The blade with a cutting width of 2.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0250.12.10.A0 MG12 The blade with a cutting width of 2.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0250.12.10.A0 TH35 The blade with a cutting width of 2.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0250.12.10.A0 TN35 The blade with a cutting width of 2.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0250.17.12.20 MG12 The blade with a cutting width of 2.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0250.17.12.20 TH35 The blade with a cutting width of 2.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0250.17.12.20 TN35 The blade with a cutting width of 2.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0250.17.12.A0 MG12 The blade with a cutting width of 2.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0250.17.12.A0 TH35 The blade with a cutting width of 2.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0250.17.12.A0 TN35 The blade with a cutting width of 2.5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0300.12.10.20 MG12 The blade with a cutting width of 3 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0300.12.10.20 TH35 The blade with a cutting width of 3 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0300.12.10.20 TN35 The blade with a cutting width of 3 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0300.12.10.A0 MG12 The blade with a cutting width of 3 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0300.12.10.A0 TH35 The blade with a cutting width of 3 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0300.12.10.A0 TN35 The blade with a cutting width of 3 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0300.17.12.20 MG12 The blade with a cutting width of 3 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0300.17.12.20 TH35 The blade with a cutting width of 3 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0300.17.12.20 TN35 The blade with a cutting width of 3 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0300.17.12.A0 MG12 The blade with a cutting width of 3 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0300.17.12.A0 TH35 The blade with a cutting width of 3 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0300.17.12.A0 TN35 The blade with a cutting width of 3 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0320.22.17.20 MG12 The blade with a cutting width of 3.2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0320.22.17.20 TH35 The blade with a cutting width of 3.2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0320.22.17.20 TN35 The blade with a cutting width of 3.2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0320.28.20.20 MG12 The blade with a cutting width of 3.2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0320.28.20.20 TH35 The blade with a cutting width of 3.2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0320.28.20.20 TN35 The blade with a cutting width of 3.2 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0400.17.12.20 MG12 The blade with a cutting width of 4 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0400.17.12.20 TH35 The blade with a cutting width of 4 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0400.17.12.20 TN35 The blade with a cutting width of 4 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0400.17.12.A0 MG12 The blade with a cutting width of 4 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0400.17.12.A0 TH35 The blade with a cutting width of 4 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0400.17.12.A0 TN35 The blade with a cutting width of 4 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0400.22.17.20 MG12 The blade with a cutting width of 4 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0400.22.17.20 TH35 The blade with a cutting width of 4 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0400.22.17.20 TN35 The blade with a cutting width of 4 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0400.28.20.20 MG12 The blade with a cutting width of 4 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0400.28.20.20 TH35 The blade with a cutting width of 4 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0400.28.20.20 TN35 The blade with a cutting width of 4 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0480.22.17.20 MG12 The blade with a cutting width of 4.8 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0480.22.17.20 TH35 The blade with a cutting width of 4.8 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0480.22.17.20 TN35 The blade with a cutting width of 4.8 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0500.17.12.20 MG12 The blade with a cutting width of 5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0500.17.12.20 TH35 The blade with a cutting width of 5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0500.17.12.20 TN35 The blade with a cutting width of 5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0500.17.12.A0 MG12 The blade with a cutting width of 5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0500.17.12.A0 TH35 The blade with a cutting width of 5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0500.17.12.A0 TN35 The blade with a cutting width of 5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0500.28.20.20 MG12 The blade with a cutting width of 5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0500.28.20.20 TH35 The blade with a cutting width of 5 mm is suitable for parting and grooving. |
|
Paul Horn HCC.0500.28.20.20 TN35 The blade with a cutting width of 5 mm is suitable for parting and grooving. |
|
Paul Horn HDC.HSKA050.06.070 System Recording as hydraulic expansion chuck with HSK A 50, clamping diameter 6 mm. |
|
Paul Horn HDC.HSKA050.08.070 System Recording as hydraulic expansion chuck with HSK A 50, clamping diameter 8 mm. |
