|
Paul Horn R114.0200.02 TI25 Insert to Inneneinstechen of grooves from bore diameter 14 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn R114.0200.02 TN35 Insert to Inneneinstechen of grooves from bore diameter 14 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn R114.0200.1.02 TH35 Insert for Inneneinstechen of grooves from bore diameter 16.5 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 6.5 mm deep. |
|
Paul Horn R114.0200.1.02 TI25 Insert to Inneneinstechen of grooves from bore diameter 16.5 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 6.5 mm deep. |
|
Paul Horn R114.0200.1.02 TN35 Insert to Inneneinstechen of grooves from bore diameter 16.5 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 6.5 mm deep. |
|
Paul Horn R114.0205.01 TH35 Insert for chasing of metric internal thread (part profile) from bore diameter 14 mm with 0.5-0.75 mm pitch. |
|
Paul Horn R114.0205.01 TN35 Insert for chasing of metric internal thread (part profile) from bore diameter 14 mm with 0.5-0.75 mm pitch. |
|
Paul Horn R114.0250.00 MG12 Insert for Inneneinstechen of grooves from bore diameter 14 mm with width 2.5 mm (corner radius 0 mm) and a maximum of 4 mm deep. |
|
Paul Horn R114.0250.00 TH35 Insert for Inneneinstechen of grooves from bore diameter 14 mm with width 2.5 mm (corner radius 0 mm) and a maximum of 4 mm deep. |
|
Paul Horn R114.0250.00 TN35 Insert to Inneneinstechen of grooves from bore diameter 14 mm with width 2.5 mm (corner radius 0 mm) and a maximum of 4 mm deep. |
|
Paul Horn R114.0250.1.02 TH35 Insert for Inneneinstechen of grooves from bore diameter 16.5 mm with 2.5 mm width (nose radius 0.2 mm) and a maximum of 6.5 mm deep. |
|
Paul Horn R114.0250.1.02 TN35 Insert to Inneneinstechen of grooves from bore diameter 16.5 mm with 2.5 mm width (nose radius 0.2 mm) and a maximum of 6.5 mm deep. |
|
Paul Horn R114.0300.00 MG12 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 3 mm width (corner radius 0 mm) and a maximum of 4 mm deep. |
|
Paul Horn R114.0300.00 TH35 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 3 mm width (corner radius 0 mm) and a maximum of 4 mm deep. |
|
Paul Horn R114.0300.00 TN35 Insert to Inneneinstechen of grooves from bore diameter 14 mm with 3 mm width (corner radius 0 mm) and a maximum of 4 mm deep. |
|
Paul Horn R114.0300.1.02 TH35 Insert for Inneneinstechen of grooves from bore diameter 16.5 mm with 3 mm width (nose radius 0.2 mm) and a maximum of 6.5 mm deep. |
|
Paul Horn R114.0300.1.02 TN35 Insert to Inneneinstechen of grooves from bore diameter 16.5 mm with 3 mm width (nose radius 0.2 mm) and a maximum of 6.5 mm deep. |
|
Paul Horn R114.0510.01 TH35 Insert for chasing of metric internal thread (part profile) from bore diameter 14 mm with 1-1.25 mm lead. |
|
Paul Horn R114.0510.01 TN35 Insert for chasing of metric internal thread (part profile) from bore diameter 14 mm with 1-1.25 mm lead. |
|
Paul Horn R114.0510.02 TN35 Insert for chasing of metric internal thread (solid profile) from bore diameter 14 mm with 1 mm pitch. |
|
Paul Horn R114.0572.04.B CB10 Insert CBN equipped for hard internal turning and copying from bore diameter 12.5 mm with a corner radius of 0.4 mm. |
|
Paul Horn R114.0815.01 TH35 Insert for chasing of metric internal thread (part profile) from bore diameter 14 mm with 1.5-1.75 mm pitch. |
|
Paul Horn R114.0815.01 TN35 Insert for chasing of metric internal thread (part profile) from bore diameter 14 mm with 1.5-1.75 mm pitch. |
|
Paul Horn R114.0815.02 TN35 Insert for chasing of metric internal thread (solid profile) from bore diameter 14 mm with 1.5 mm pitch. |
|
Paul Horn R114.0815.45 MG12 Insert deep to preparting and chamfers from bore diameter 14 mm with 1.5 mm width and a maximum of 1.5 mm. |
|
Paul Horn R114.0815.45 TI25 Insert deep to preparting and chamfers from bore diameter 14 mm with 1.5 mm width and a maximum of 1.5 mm. |
|
Paul Horn R114.1020.01 TH35 Insert for chasing of metric internal thread (part profile) from bore diameter 14 mm with 2 mm pitch. |
|
Paul Horn R114.1020.01 TN35 Insert for chasing of metric internal thread (part profile) from bore diameter 14 mm with 2 mm pitch. |
|
Paul Horn R114.1020.02 TN35 Insert for chasing of metric internal thread (part profile) from bore diameter 14 mm with 2 mm pitch. |
|
Paul Horn R114.1205.00 TN35 Insert deep for axial grooving from outer groove diameter 12 mm with 0.5 mm width and a maximum of 1.0 mm. |
|
Paul Horn R114.1210.00 TN35 Insert deep for axial grooving from outer groove diameter 12 mm with 1 mm wide and a maximum of 1.5 mm. |
|
Paul Horn R114.1215.00 TN35 Insert deep for axial grooving from outer groove diameter 12 mm with 1.5 mm width and a maximum of 2.5 mm. |
|
Paul Horn R114.1220.00 TN35 Insert deep for axial grooving from outer groove diameter 12 mm with 2 mm wide and up to 3 mm. |
|
Paul Horn R114.1220.5.00 TN35 Insert deep for axial grooving from outer groove diameter 12 mm with 2 mm width and a maximum of 5 mm. |
|
Paul Horn R114.1220.5.10 TN35 Insert deep for axial grooving from outer groove diameter 12 mm with 2 mm width and a maximum of 5 mm. |
|
Paul Horn R114.1225.00 TN35 Insert deep for axial grooving from outer groove diameter 12 mm of width 2.5 mm and a maximum of 3 mm. |
|
Paul Horn R114.1225.5.00 TN35 Insert deep for axial grooving from outer groove diameter 12 mm of width 2.5 mm and 5 mm maximum. |
|
Paul Horn R114.1225.5.12 TN35 Insert deep for axial grooving from outer groove diameter 12 mm of width 2.5 mm and 5 mm maximum. |
|
Paul Horn R114.1230.00 TN35 Insert deep for axial grooving from outer groove diameter 12 mm with 3 mm wide and up to 3 mm. |
|
Paul Horn R114.1230.6.00 TN35 Insert deep for axial grooving from outer groove diameter 12 mm with 3 mm wide and a maximum of 6 mm. |
|
Paul Horn R114.1230.6.15 TN35 Insert deep for axial grooving from outer groove diameter 12 mm with 3 mm wide and a maximum of 6 mm. |
|
Paul Horn R114.1325.01 TH35 Insert for chasing of metric internal thread (part profile) from bore diameter 14 mm with 2.5 mm pitch. |
|
Paul Horn R114.1325.01 TN35 Insert for chasing of metric internal thread (part profile) from bore diameter 14 mm with 2.5 mm pitch. |
|
Paul Horn R114.1325.02 TN35 Insert for chasing of metric internal thread (solid profile) from bore diameter 14 mm with 2.5 mm pitch. |
|
Paul Horn R114.1410.00 MG12 Insert for axial grooving from outer groove diameter 14 mm with 1 mm width (corner radius 0 mm) and a maximum of 1.5 mm deep. |
|
Paul Horn R114.1410.00 TN35 Insert for axial grooving from outer groove diameter 14 mm with 1 mm width (corner radius 0 mm) and a maximum of 1.5 mm deep. |
|
Paul Horn R114.1410.05 TN35 Insert deep for axial grooving from outer groove diameter 14 mm with 1 mm width, full radius 0.5 mm and a maximum of 1.5 mm. |
|
Paul Horn R114.1415.00 TN35 Insert for axial grooving from outer groove diameter 14 mm with 1.5 mm width (nose radius 0.2 mm) and a maximum of 2.5 mm deep. |
|
Paul Horn R114.1416.08 TN35 Insert deep for axial grooving from outer groove diameter 14 mm with 1.6 mm width, full radius 0.8 mm and a maximum of 2.5 mm. |
|
Paul Horn R114.1420.00 TN35 Insert for axial grooving from outer groove diameter 14 mm with 2 mm width (nose radius 0.2 mm) and a maximum depth of 3 mm. |
|
Paul Horn R114.1420.10 TN35 Insert deep for axial grooving from outer groove diameter 14 mm with 2 mm width, full radius 1 mm and a maximum of 3 mm. |
|
Paul Horn R114.1420.5.00 TN35 Insert for axial grooving from outer groove diameter 14 mm with 2 mm width (nose radius 0.2 mm) and a maximum depth of 5 mm. |
|
Paul Horn R114.1425.00 TN35 Insert for axial grooving from outer groove diameter 14 mm with 2.5 mm width (nose radius 0.2 mm) and a maximum depth of 3 mm. |
|
Paul Horn R114.1425.12 TN35 Insert deep for axial grooving from outer groove diameter 14 mm of width 2.5 mm, full radius 1.25mm and a maximum of 3 mm. |
|
Paul Horn R114.1425.5.00 TN35 Insert for axial grooving from outer groove diameter 14 mm with 2.5 mm width (nose radius 0.2 mm) and a maximum depth of 5 mm. |
|
Paul Horn R114.1430.00 MG12 Insert for axial grooving from outer groove diameter 14 mm with 3 mm width (nose radius 0.2 mm) and a maximum depth of 3 mm. |
|
Paul Horn R114.1430.00 TN35 Insert for axial grooving from outer groove diameter 14 mm with 3 mm width (nose radius 0.2 mm) and a maximum depth of 3 mm. |
|
Paul Horn R114.1430.15 TN35 Insert deep for axial grooving from outer groove diameter 14 mm with 3 mm width, full radius of 1.5 mm and a maximum of 3 mm. |
|
Paul Horn R114.1430.6.00 TN35 Insert for axial grooving from outer groove diameter 14 mm with 3 mm width (nose radius 0.2 mm) and a maximum of 6 mm deep. |
|
Paul Horn R114.1730.01 TN35 Insert R114.L114.1730.01 TN35 for chasing of metric ISO internal trapezoidal thread to DIN 103 from bore diameter 14 mm with 3 mm pitch. |
|
Paul Horn R114.1890.02 MG12 Insert for internal turning and copying from bore diameter 13.8 mm with a corner radius of 0.2 mm. |
|
Paul Horn R114.1890.02 TH35 Insert for internal turning and copying from bore diameter 13.8 mm with a corner radius of 0.2 mm. |
|
Paul Horn R114.1890.02 TN35 Insert for internal turning and copying from bore diameter 13.8 mm with a corner radius of 0.2 mm. |
|
Paul Horn R114.2240.01 TN35 Insert for chasing of metric ISO internal trapezoidal thread to DIN 103 from bore diameter 14 mm with 4 mm pitch. |
|
Paul Horn R114.2750.01 TN35 Insert for chasing of metric ISO internal trapezoidal thread to DIN 103 from bore diameter 14 mm with 5 mm pitch. |
|
Paul Horn R114.3090.02 TH35 Insert rear turning and copying from bore diameter 13.8 mm with a corner radius of 0.2 mm. |
|
Paul Horn R114.3090.02 TN35 Insert rear turning and copying from bore diameter 13.8 mm with a corner radius of 0.2 mm. |
|
Paul Horn R114.4710.02 TH35 Insert for internal turning and copying from bore diameter 16 mm with a corner radius of 0.2 mm. |
|
Paul Horn R114.4710.02 TN35 Insert for internal turning and copying from bore diameter 16 mm with a corner radius of 0.2 mm. |
|
Paul Horn R114.4787.02 TH35 Insert for internal turning and copying from bore diameter 13.8 mm with a corner radius of 0.2 mm. |
|
Paul Horn R114.4787.02 TN35 Insert for internal turning and copying from bore diameter 13.8 mm with a corner radius of 0.2 mm. |
|
Paul Horn R114.4787.04 TH35 Insert for internal turning and copying from bore diameter 13.8 mm with a corner radius of 0.4 mm. |
|
Paul Horn R114020002TH35 Insert to Inneneinstechen of grooves from bore diameter 14 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn R116.0009.18 MG12 Insert deep for the cutting of grooves from bore diameter 16 mm with 1.8 mm width, full radius of 0.9 mm and a maximum of 4.3 mm. |
|
Paul Horn R116.0009.18 TH35 Insert deep for the cutting of grooves from bore diameter 16 mm with 1.8 mm width, full radius of 0.9 mm and a maximum of 4.3 mm. |
|
Paul Horn R116.0009.18 TN35 Insert deep for the cutting of grooves from bore diameter 16 mm with 1.8 mm width, full radius of 0.9 mm and a maximum of 4.3 mm. |
|
Paul Horn R116.0011.22 MG12 Insert for cutting of grooves from bore diameter 16 mm with 2.2 mm width, full radius 1.1 mm and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0011.22 TH35 Insert deep for the cutting of grooves from bore diameter 16 mm with 2.2 mm width, full radius 1.1 mm and a maximum of 4.3 mm. |
|
Paul Horn R116.0011.22 TN35 Insert deep for the cutting of grooves from bore diameter 16 mm with 2.2 mm width, full radius 1.1 mm and a maximum of 4.3 mm. |
|
Paul Horn R116.0015.30 MG12 Insert deep for the cutting of grooves from bore diameter 16 mm with 3 mm width, full radius of 1.5 mm and a maximum of 4.3 mm. |
|
Paul Horn R116.0015.30 TH35 Insert deep for the cutting of grooves from bore diameter 16 mm with 3 mm width, full radius of 1.5 mm and a maximum of 4.3 mm. |
|
Paul Horn R116.0015.30 TN35 Insert deep for the cutting of grooves from bore diameter 16 mm with 3 mm width, full radius of 1.5 mm and a maximum of 4.3 mm. |
|
Paul Horn R116.0020.40 MG12 Insert for cutting of grooves from bore diameter 16 mm with 4 mm width, full radius 2 mm and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0020.40 TH35 Insert deep for the cutting of grooves from bore diameter 16 mm with 4 mm width, full radius 2 mm and a maximum of 4.3 mm. |
|
Paul Horn R116.0020.40 TN35 Insert deep for the cutting of grooves from bore diameter 16 mm with 4 mm width, full radius 2 mm and a maximum of 4.3 mm. |
|
Paul Horn R116.0070.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 16 mm with 0.74 mm width (nominal width 0.7 mm) and a maximum of 1.2 mm deep. |
|
Paul Horn R116.0080.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 16 mm with 0.84 mm width (nominal width 0.8 mm) and a maximum of 1.3 mm deep. |
|
Paul Horn R116.0090.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 16 mm with 0.94 mm width (nominal width 0.9 mm) and a maximum of 1.5 mm deep. |
|
Paul Horn R116.0110.00 MG12 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 16 mm with 1.19 width (nominal width 1.1 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0110.00 TH35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 16 mm with 1.19 width (nominal width 1.1 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0110.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 16 mm with 1.19 width (nominal width 1.1 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0130.00 MG12 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 16 mm 1.39 mm width (nominal width 1.3 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0130.00 TH35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 16 mm 1.39 mm width (nominal width 1.3 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0130.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 16 mm 1.39 mm width (nominal width 1.3 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0160.00 MG12 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 16 mm with 1.69 mm width (nominal width 1.6 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0160.00 TH35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 16 mm with 1.69 mm width (nominal width 1.6 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0160.00 TN35 Insert for producing Seegerringnuten DIN 471/472 from bore diameter 16 mm with 1.69 mm width (nominal width 1.6 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0200.00 MG12 Insert for Inneneinstechen of grooves from bore diameter 16 mm with 2 mm width (corner radius 0 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0200.00 TH35 Insert for Inneneinstechen of grooves from bore diameter 16 mm with 2 mm width (corner radius 0 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0200.00 TN35 Insert to Inneneinstechen of grooves from bore diameter 16 mm with 2 mm width (corner radius 0 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0200.02 TH35 Insert for Inneneinstechen of grooves from bore diameter 16 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0200.02 TN35 Insert to Inneneinstechen of grooves from bore diameter 16 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0250.00 MG12 Insert for Inneneinstechen of grooves from bore diameter 16 mm with width 2.5 mm (corner radius 0 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0250.00 TH35 Insert for Inneneinstechen of grooves from bore diameter 16 mm with width 2.5 mm (corner radius 0 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0250.00 TN35 Insert to Inneneinstechen of grooves from bore diameter 16 mm with width 2.5 mm (corner radius 0 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0300.00 MG12 Insert for Inneneinstechen of grooves from bore diameter 16 mm with 3 mm width (corner radius 0 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0300.00 TH35 Insert for Inneneinstechen of grooves from bore diameter 16 mm with 3 mm width (corner radius 0 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0300.00 TN35 Insert to Inneneinstechen of grooves from bore diameter 16 mm with 3 mm width (corner radius 0 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0350.00 MG12 Insert for Inneneinstechen of grooves from bore diameter 16 mm with 3.5 mm width (corner radius 0 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0350.00 TH35 Insert for Inneneinstechen of grooves from bore diameter 16 mm with 3.5 mm width (corner radius 0 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0350.00 TN35 Insert to Inneneinstechen of grooves from bore diameter 16 mm with 3.5 mm width (corner radius 0 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0400.00 MG12 Insert for Inneneinstechen of grooves from bore diameter 16 mm with 4 mm width (corner radius 0 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0400.00 TH35 Insert for Inneneinstechen of grooves from bore diameter 16 mm with 4 mm width (corner radius 0 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0400.00 TN35 Insert to Inneneinstechen of grooves from bore diameter 16 mm with 4 mm width (corner radius 0 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn R116.0510.01 TH35 Insert for chasing of metric internal thread (part profile) from bore diameter 16 mm with 1-1.25 mm lead. |
|
Paul Horn R116.0510.01 TN35 Insert for chasing of metric internal thread (part profile) from bore diameter 16 mm with 1-1.25 mm lead. |
|
Paul Horn R116.0510.02 TN35 Insert for chasing of metric internal thread (solid profile) from bore diameter 16 mm with 1 mm pitch. |
|
Paul Horn R116.0582.04.B CB10 Insert CBN equipped for hard internal turning from bore diameter 14 mm with a corner radius of 0.4 mm. |
|
Paul Horn R116.0815.01 TH35 Insert for chasing of metric internal thread (part profile) from bore diameter 16 mm with 1.5-1.75 mm pitch. |
|
Paul Horn R116.0815.01 TN35 Insert for chasing of metric internal thread (part profile) from bore diameter 16 mm with 1.5-1.75 mm pitch. |
|
Paul Horn R116.0815.02 TN35 Insert for chasing of metric internal thread (solid profile) from bore diameter 16 mm with 1.5 mm pitch. |
|
Paul Horn R116.0815.45 MG12 Insert deep to preparting and chamfering from bore diameter 16 mm with 1.5 mm width and a maximum of 1.5 mm. |
|
Paul Horn R116.0815.45 TI25 Insert deep to preparting and chamfering from bore diameter 16 mm with 1.5 mm width and a maximum of 1.5 mm. |
|
Paul Horn R116.1020.01 TH35 Insert for chasing of metric internal thread (part profile) from bore diameter 16 mm with 2 mm pitch. |
|
Paul Horn R116.1020.01 TN35 Insert for chasing of metric internal thread (part profile) from bore diameter 16 mm with 2 mm pitch. |
|
Paul Horn R116.1020.02 TN35 Insert for chasing of metric internal thread (solid profile) from bore diameter 16 mm with 2 mm pitch. |
|
Paul Horn R116.1220.01 TN35 Insert for chasing of metric ISO internal trapezoidal thread to DIN 103 from bore diameter 16 mm with 2 mm pitch. |
|
Paul Horn R116.1325.01 TH35 Insert for chasing of metric internal thread (part profile) from bore diameter 16 mm with 2.5 mm pitch. |
|
Paul Horn R116.1325.01 TN35 Insert for chasing of metric internal thread (part profile) from bore diameter 16 mm with 2.5 mm pitch. |
|
Paul Horn R116.1325.02 TN35 Insert for chasing of metric internal thread (solid profile) from bore diameter 16 mm with 2.5 mm pitch. |
|
Paul Horn R116.1630.02 TN35 Insert for chasing of metric internal thread (solid profile) from bore diameter 16 mm with 3 mm pitch. |
|
Paul Horn R116.1730.01 TN35 Insert for chasing of metric ISO internal trapezoidal thread to DIN 103 from bore diameter 16 mm with 3 mm pitch. |
|
Paul Horn R116.1835.02 TN35 Insert for chasing of metric internal thread (solid profile) from bore diameter 16 mm with 3.5 mm pitch. |
|
Paul Horn R116.1897.02 TH35 Insert for internal turning and copying from bore diameter 15.5 mm with a corner radius of 0.2 mm. |
|
Paul Horn R116.1897.02 TN35 Insert for internal turning and copying from bore diameter 15.5 mm with a corner radius of 0.2 mm. |
|
Paul Horn R116.2140.02 TN35 Insert for chasing of metric internal thread (solid profile) from bore diameter 16 mm with 4 mm pitch. |
|
Paul Horn R116.2240.01 TN35 Insert for chasing of metric ISO internal trapezoidal thread to DIN 103 from bore diameter 16 mm with 4 mm pitch. |
|
Paul Horn R116.2750.01 TN35 Insert for chasing of metric ISO internal trapezoidal thread to DIN 103 from bore diameter 16 mm with 5 mm pitch. |
|
Paul Horn R116.3560.01 TI25 Insert for chasing of metric ISO internal trapezoidal thread to DIN 103 from bore diameter 16 mm with 6 mm pitch. |
|
Paul Horn R116.4702.02 TH35 Insert for internal turning and copying from bore diameter 16 mm with a corner radius of 0.2 mm. |
|
Paul Horn R116.4702.02 TN35 Insert for internal turning and copying from bore diameter 16 mm with a corner radius of 0.2 mm. |
|
Paul Horn R116.4702.04 TH35 Insert for internal turning and copying from bore diameter 16 mm with a corner radius of 0.4 mm. |
|
Paul Horn R116.5511.02 TN35 Insert to Strehlen of Whitworth pipe thread (solid profile) from bore diameter 16 mm with 11 threads / inch pitch. |
|
Paul Horn R116.5514.02 TN35 Insert to Strehlen of Whitworth pipe thread (solid profile) from bore diameter 16 mm with 14 transition / inch pitch. |
|
Paul Horn R11P.0100.1.00 TH35 The insert with a cutting width of 1 mm is suitable for penetration of inner contours with up to 2.5 mm deep. |
|
Paul Horn R11P.0100.2.00 TH35 The insert with a cutting width of 1 mm is suitable for penetration of inner contours with up to 3.5 mm deep. |
|
Paul Horn R11P.0150.1.00 TH35 The insert with a cutting width of 1.5 mm is suitable for penetration of inner contours with up to 2.5 mm deep. |
|
Paul Horn R11P.0150.2.00 TH35 The insert with a cutting width of 1.5 mm is suitable for penetration of inner contours with up to 3.5 mm deep. |
|
Paul Horn R11P.0200.1.02 TH35 The insert with a cutting width of 2 mm is suitable for penetration of inner contours with depths up to 2.5 mm. |
|
Paul Horn R11P.0200.2.02 TH35 The insert with a cutting width of 2 mm is suitable for penetration of inner contours with up to 3.5 mm deep. |
|
Paul Horn R11P.0250.1.02 TH35 The insert with a cutting width of 2.5 mm is suitable for penetration of inner contours with depths up to 2.5 mm. |
|
Paul Horn R11P.0300.1.02 TH35 The insert with a cutting width of 3 mm is suitable for penetration of inner contours with depths up to 2.5 mm. |
|
Paul Horn R11P.1865.1.02 TH35 The insert suitable for bore-turning and grooving of inner contours with depths up to 2.5 mm. |
|
Paul Horn R125.0608.00 Quick clamp holder for installation purposes for receiving inserts type 111 from bore diameter 20.00 mm, version right. |
|
Paul Horn R145.1012.00 Quick clamp holder for installation purposes for receiving inserts type 116 from bore diameter 32.00 mm, version right. |
|
Paul Horn R18P.0009.1.18 TH35 The insert with a cutting width of 1.8 mm is suitable for grooving of the inner edges up to 6 mm depth. |
|
Paul Horn R18P.0011.1.22 TH35 The insert with a cutting width of 2.2 mm is suitable for grooving of the inner edges up to 6 mm depth. |
|
Paul Horn R18P.0015.1.30 TH35 The insert with a cutting width of 3 mm is suitable for grooving of the inner edges up to 6 mm depth. |
|
Paul Horn R210.1616.03 Tool holders with shank 16.00 mm wide x 16.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11.00 mm and of clamping range 3.0 - 4.0 mm, v |
|
Paul Horn R210.2020.02 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range 2.5 - 3.0 mm, |
|
Paul Horn R210.2020.03 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range 3.0 - 4.0 mm, |
|
Paul Horn R210.2020.04 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range 3.0 - 4.0 mm, |
|
Paul Horn R210.2020.05 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range from 5.1 to 6. |
|
Paul Horn R210.2020.07 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range from 6.1 to 8. |
|
Paul Horn R210.2020.08 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range from 7.6 to 8. |
|
Paul Horn R210.2020.09 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and a clamping range of 0 mm, versio |
|
Paul Horn R210.2525.02 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range 2.5 - 3.0 mm, v |
|
Paul Horn R210.2525.03 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range 3.0 - 4.0 mm, v |
|
Paul Horn R210.2525.04 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range 4,0 - 5,0 mm, v |
|
Paul Horn R210.2525.05 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range from 5.1 to 6.0 |
|
Paul Horn R210.2525.07 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range from 6.1 to 8.0 |
|
Paul Horn R210.2525.08 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range from 7.6 to 8.0 |
|
Paul Horn R210.2525.09 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and a clamping range of 0 mm, version |
|
Paul Horn R210.2525.K3 Basic holder with shaft 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range 3.0 - 4.0 mm, v |
|
Paul Horn R210.2525.K4 Basic holder with shaft 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range 4,0 - 5,0 mm, v |
|
Paul Horn R210.3225.03 Tool holders with shank 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range 3.0 - 4.0 mm, v |
|
Paul Horn R210.3225.04 Tool holders with shank 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range 4,0 - 5,0 mm, v |
|
Paul Horn R210.3225.05 Tool holders with shank 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range from 5.1 to 6.0 |
|
Paul Horn R210.3225.07 Tool holders with shank 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range from 6.1 to 8.0 |
|
Paul Horn R211.2020.02 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts type 231 with a maximum penetration depth 11:00 mm and of clamping range 2.5 - 3.0 mm, |
|
Paul Horn R211.2020.03 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts type 231 with a maximum penetration depth 11:00 mm and of clamping range 3.0 - 4.0 mm, |
|
Paul Horn R211.2020.04 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts type 231 with a maximum penetration depth 11:00 mm and of clamping range 4,0 - 5,0 mm, |
|
Paul Horn R211.2020.05 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts type 231 with a maximum penetration depth 11:00 mm and of clamping range from 5.0 to 6. |
|
Paul Horn R211.2020.07 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts type 231 with a maximum penetration depth 11:00 mm and of clamping range from 6.5 to 8. |
|
Paul Horn R211.2020.09 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts type 231 with a maximum penetration depth 11:00 mm and of clamping range from 8.5 to 10 |
|
Paul Horn R211.2525.02 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts type 231 with a maximum penetration depth 11:00 mm and a clamping range of 0 mm, version |
|
Paul Horn R211.2525.03 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts type 231 with a maximum penetration depth 11:00 mm and of clamping range 3.0 - 4.0 mm, v |
|
Paul Horn R211.2525.04 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts type 231 with a maximum penetration depth 11:00 mm and of clamping range 4,0 - 5,0 mm, v |
|
Paul Horn R211.2525.05 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts type 231 with a maximum penetration depth 11:00 mm and of clamping range from 5.0 to 6.5 |
|
Paul Horn R211.2525.07 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts type 231 with a maximum penetration depth 11:00 mm and of clamping range from 6.5 to 8.5 |
|
Paul Horn R211.2525.09 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts type 231 with a maximum penetration depth 11:00 mm and of clamping range from 8.5 to 10. |
|
Paul Horn R211.3232.04 Tool holders with shank 32.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts type 231 with a maximum penetration depth 11:00 mm and of clamping range 4,0 - 5,0 mm, v |
|
Paul Horn R213.0025.03 Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 38.00 mm for receiving inserts Type 229 with a maximum penetration depth 7:50 mm and of clampi |
|
Paul Horn R213.0025.04 Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 38.00 mm for receiving inserts Type 229 with a maximum penetration depth 7:50 mm and of clampi |
|
Paul Horn R213.0032.0.03 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 46.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R213.0032.0.03IK Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 46.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R213.0032.0.04 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 46.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R213.0032.0.04IK Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 46.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R213.0032.0.05 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 46.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R213.0032.03 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 38.00 mm for receiving inserts Type 229 with a maximum penetration depth 7:50 mm and of clampi |
|
Paul Horn R213.0032.03IK Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 38.00 mm for receiving inserts Type 229 with a maximum penetration depth 7:50 mm and of clampi |
|
Paul Horn R213.0032.04 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 38.00 mm for receiving inserts Type 229 with a maximum penetration depth 7:50 mm and of clampi |
|
Paul Horn R213.0032.05 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 46.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R213.0040.0.03 Toolholder with shaft diameter 40.00 mm for internal grooving and turning with the smallest bore diameter 54.00 mm for receiving inserts Type 229 with a maximum penetration depth 11.50 mm and of clamp |
|
Paul Horn R213.0040.0.04 Toolholder with shaft diameter 40.00 mm for internal grooving and turning with the smallest bore diameter 54.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R213.0040.0.04IK Toolholder with shaft diameter 40.00 mm for internal grooving and turning with the smallest bore diameter 54.00 mm for receiving inserts Type 229 with a maximum penetration depth 11.50 mm and of clamp |
|
Paul Horn R213.0040.0.05 Toolholder with shaft diameter 40.00 mm for internal grooving and turning with the smallest bore diameter 54.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R213.0040.0.05IK Toolholder with shaft diameter 40.00 mm for internal grooving and turning with the smallest bore diameter 54.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R213.0040.03 Toolholder with shaft diameter 40.00 mm for internal grooving and turning with the smallest bore diameter 50.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R213.0040.03IK Toolholder with shaft diameter 40.00 mm for internal grooving and turning with the smallest bore diameter 50.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R213.0040.04 Toolholder with shaft diameter 40.00 mm for internal grooving and turning with the smallest bore diameter 50.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R213.0040.05 Toolholder with shaft diameter 40.00 mm for internal grooving and turning with the smallest bore diameter 50.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R213.0040.07 Toolholder with shaft diameter 40.00 mm for internal grooving and turning with the smallest bore diameter 50.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R213.0040.09 Toolholder with shaft diameter 40.00 mm for internal grooving and turning with the smallest bore diameter 50.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R213.0050.03 Toolholder with shaft diameter 50.00 mm for internal grooving and turning with the smallest bore diameter 60.00 mm for receiving inserts Type 229 with a maximum penetration depth 15:00 mm and of clamp |
|
Paul Horn R213.0050.04 Toolholder with shaft diameter 50.00 mm for internal grooving and turning with the smallest bore diameter 60.00 mm for receiving inserts Type 229 with a maximum penetration depth 15:00 mm and of clamp |
|
Paul Horn R213.0050.05 Toolholder with shaft diameter 50.00 mm for internal grooving and turning with the smallest bore diameter 60.00 mm for receiving inserts Type 229 with a maximum penetration depth 15:00 mm and of clamp |
|
Paul Horn R213.0050.07 Toolholder with shaft diameter 50.00 mm for internal grooving and turning with the smallest bore diameter 60.00 mm for receiving inserts Type 229 with a maximum penetration depth 15:00 mm and of clamp |
|
Paul Horn R214.0032.03 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 38.00 mm for receiving inserts Type 229 with a maximum penetration depth 7:50 mm and of clampi |
|
Paul Horn R214.0032.04 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 38.00 mm for receiving inserts Type 229 with a maximum penetration depth 7.50 mm and an area o |
|
Paul Horn R214.0032.05 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 46.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R214.0040.03 Toolholder with shaft diameter 40.00 mm for internal grooving and turning with the smallest bore diameter 50.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R214.0040.04 Toolholder with shaft diameter 40.00 mm for internal grooving and turning with the smallest bore diameter 50.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R214.0040.05 Toolholder with shaft diameter 40.00 mm for internal grooving and turning with the smallest bore diameter 50.00 mm for receiving inserts Type 229 with a maximum penetration depth 11.50 mm and of clamp |
|
Paul Horn R214.0040.07 Toolholder with shaft diameter 40.00 mm for internal grooving and turning with the smallest bore diameter 50.00 mm for receiving inserts Type 229 with a maximum penetration depth 11:50 mm and of clamp |
|
Paul Horn R214.0050.03 Toolholder with shaft diameter 50.00 mm for internal grooving and turning with the smallest bore diameter 60.00 mm for receiving inserts Type 229 with a maximum penetration depth 15:00 mm and of clamp |
|
Paul Horn R214.0050.04 Toolholder with shaft diameter 50.00 mm for internal grooving and turning with the smallest bore diameter 60.00 mm for receiving inserts Type 229 with a maximum penetration depth 15:00 mm and of clamp |
|
Paul Horn R214.0050.05 Toolholder with shaft diameter 50.00 mm for internal grooving and turning with the smallest bore diameter 60.00 mm for receiving inserts Type 229 with a maximum penetration depth 15:00 mm and of clamp |
|
Paul Horn R214.0050.09 Toolholder with shaft diameter 50.00 mm for internal grooving and turning with the smallest bore diameter 60.00 mm for receiving inserts Type 229 with a maximum penetration depth 15:00 mm and of clamp |
|
Paul Horn R217.1060.27 P20 The indexable insert is suitable for grooving of the inner and outer contours with up to 0.55mm depth of thread with a pitch of 0.6 mm. |
|
Paul Horn R217.1100.37 P20 The indexable insert is suitable for grooving of the inner and outer contours with up to 0.9 mm depth for thread having a pitch of 1 mm. |
|
Paul Horn R217.1125.53 P20 The indexable insert is suitable for grooving of the inner and outer contours with up to 1:05 mm depth of thread with a pitch of 1.25mm. |
|
Paul Horn R217.1150.53 P20 The indexable insert is suitable for grooving of the inner and outer contours with up to 1.2 mm depth of thread with a pitch of 1.5 mm. |
|
Paul Horn R218.1616.0.03.IK Toolholder with shank 16 mm width x 16 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 18 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R218.1616.03 Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 3.0 - 4.0 mm, ve |
|
Paul Horn R218.1616.03.IK Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 3.0 - 4.0 mm, ve |
|
Paul Horn R218.1616.2.03.IK Toolholder with shank 16 mm width x 16 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 18 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R218.1616.2.04.IK Toolholder with shank 16 mm width x 16 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 18 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R218.1616.2.05.IK Toolholder with shank 16 mm width x 16 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 18 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R218.2020.0.03.IK Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 18 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R218.2020.0.04.IK Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 18 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R218.2020.0.05.IK Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 18 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R218.2020.02 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 2.5 - 3.0 mm, |
|
Paul Horn R218.2020.02.IK Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 2.5 - 3.0 mm, |
|
Paul Horn R218.2020.03 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 3.0 - 4.0 mm, |
|
Paul Horn R218.2020.03.IK Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 3.0 - 4.0 mm, |
|
Paul Horn R218.2020.04 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 4,0 - 5,0 mm, |
|
Paul Horn R218.2020.05 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range from 5.1 to 6. |
|
Paul Horn R218.2020.07 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range from 6.1 to 8. |
|
Paul Horn R218.2020.09 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range from 8.1 to 10 |
|
Paul Horn R218.2020.2.03.IK Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 18 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R218.2020.2.04.IK Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 18 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R218.2020.2.05.IK Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 18 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R218.2525.0.03.IK Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 18 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R218.2525.0.04.IK Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 18 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R218.2525.0.05.IK Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 18 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R218.2525.02 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 2.5 - 3.0 mm, v |
|
Paul Horn R218.2525.02.IK Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 2.5 - 3.0 mm, v |
|
Paul Horn R218.2525.03 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 3.0 - 4.0 mm, v |
|
Paul Horn R218.2525.03.IK Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 3.0 - 4.0 mm, v |
|
Paul Horn R218.2525.04 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 4,0 - 5,0 mm, v |
|
Paul Horn R218.2525.05 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range from 5.1 to 6.0 |
|
Paul Horn R218.2525.07 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range from 6.1 to 8.0 |
|
Paul Horn R218.2525.08 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range from 7.6 to 8.0 |
|
Paul Horn R218.2525.09 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range from 8.1 to 10. |
|
Paul Horn R218.2525.2.03.IK Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 18 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R218.2525.2.04.IK Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 18 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R218.2525.2.05.IK Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 18 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R218.2525.K3 Basic holder with shaft 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 3.0 - 4.0 mm, v |
|
Paul Horn R218.2525.K4 Basic holder with shaft 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 4,0 - 5,0 mm, v |
|
Paul Horn R218.2525.K5 Basic holder with shaft 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range from 5.1 to 6.0 |
|
Paul Horn R218.3225.03 Tool holders with shank 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 3.0 - 4.0 mm, v |
|
Paul Horn R218.3225.03.IK Tool holders with shank 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 3.0 - 4.0 mm, v |
|
Paul Horn R218.3225.04 Tool holders with shank 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18.00 mm and of clamping range 4,0 - 5,0 mm, v |
|
Paul Horn R218.3225.05 Tool holders with shank 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range from 5.1 to 6.0 |
|
Paul Horn R218.3225.07 Tool holders with shank 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range from 6.1 to 8.0 |
|
Paul Horn R218.3225.09 Tool holders with shank 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range from 8.1 to 10. |
|
Paul Horn R218.3225.K3 Basic holder with shaft 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 3.0 - 4.0 mm, v |
|
Paul Horn R218.3225.K4 Basic holder with shaft 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 18:00 mm and of clamping range 4,0 - 5,0 mm, v |
|
Paul Horn R218.5.7 Clamping element, Spare part z. B. for tool holder of the indexable insert system 229 |
|
Paul Horn R218.5.7.32 Clamping element, Spare part z. B. for short clamping holder type R257.2222.07 |
|
Paul Horn R218.9 Clamping element, Spare part z. B. for tool holder type R218 ... .09, R218 ... .K9 |
|
Paul Horn R218.9.32 Clamping element, Spare part z. B. for short clamping holder type R257.2222.09 |
|
Paul Horn R219.2020.03 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range 3.0 - 4.0 mm, |
|
Paul Horn R219.2020.04 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range 4,0 - 5,0 mm, |
|
Paul Horn R219.2020.05 Tool holders with shank 20.00 mm wide x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 15.00 mm and of clamping range from 5.1 to 6.0 |
|
Paul Horn R219.2020.07 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 15:00 mm and of clamping range from 6.1 to 8. |
|
Paul Horn R219.2525.03 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range 3.0 - 4.0 mm, v |
|
Paul Horn R219.2525.04 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 11:00 mm and of clamping range 4,0 - 5,0 mm, v |
|
Paul Horn R219.2525.05 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 15:00 mm and of clamping range 5.1 - 6.0 mm, v |
|
Paul Horn R219.2525.07 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 15:00 mm and of clamping range from 6.1 to 8.0 |
|
Paul Horn R220.00C3.K1 Basic holder for cassette type 220 |
|
Paul Horn R220.00C3.K1.IK Basic holder for cassette type 220 |
|
Paul Horn R220.00C3.K2 Basic holder for cassette type 220 |
|
Paul Horn R220.00C3.K2.IK Basic holder for cassette type 220 |
|
Paul Horn R220.00C4.K1 Basic holder for cassette type 220 |
|
Paul Horn R220.00C4.K1.IK Basic holder for cassette type 220 |
|
Paul Horn R220.00C4.K10.IK Basic holder R220.00C4.K1.IK for cassette type 220 |
|
Paul Horn R220.00C4.K2 Basic holder for cassette type 220 |
|
Paul Horn R220.00C4.K2.IK Basic holder for cassette type 220 |
|
Paul Horn R220.00C4.K20.IK Basic holder for cassette type 220 |
|
Paul Horn R220.00C5.K1 Basic holder for cassette type 220 |
|
Paul Horn R220.00C5.K1.IK Basic holder for cassette type 220 |
|
Paul Horn R220.00C5.K10.IK Basic holder for cassette type 220 |
|
Paul Horn R220.00C5.K2 Basic holder for cassette type 220 |
|
Paul Horn R220.00C5.K2.IK Basic holder for cassette type 220 |
|
Paul Horn R220.00C5.K20.IK Basic holder for cassette type 220 |
|
Paul Horn R220.00C6.K1 Basic holder for cassette type 220 |
|
Paul Horn R220.00C6.K1.IK Basic holder for cassette type 220 |
|
Paul Horn R220.00C6.K2 Basic holder for cassette type 220 |
|
Paul Horn R220.00C6.K2.IK Basic holder for cassette type 220 |
|
Paul Horn R220.00C8.K1.IK Basic holder for cassette type 220 |
|
Paul Horn R220.00C8.K2.IK Basic holder for cassette type 220 |
|
Paul Horn R220.1616.K1 Basic holder for cassette type 220 with stem 16.00mm width x 16.00mm height, execution law. |
|
Paul Horn R220.1616.K2 Basic holder for cassette type 220 with stem 16.00mm width x 16.00mm height, execution law. |
|
Paul Horn R220.2020.2.K1.IK Basic holder for cassette type 220 with shaft 20.00 mm Width x 20.00 mm height, execution law. |
|
Paul Horn R220.2020.2.K2.IK Basic holder for cassette type 220 with shaft 20.00 mm Width x 20.00 mm height, execution law. |
|
Paul Horn R220.2020.K2 Basic holder for cassette type 220 with shaft 20.00 mm Width x 20.00 mm height, execution law. |
|
Paul Horn R220.2525.2.K1.IK Basic holder for cassette type 220 with shank 25 mm width x 25 mm height, execution law. |
|
Paul Horn R220.2525.2.K2.IK Basic holder for cassette type 220 with shank 25 mm width x 25 mm height, execution law. |
|
Paul Horn R220.2525.K2 Basic holder for cassette type 220 with shaft 25.00 mm wide x 25.00 mm height, execution law. |
|
Paul Horn R220.2535.60.K1 Body type |
|
Paul Horn R220.3225.K1 Basic holder for cassette type 220 with shank 0 mm wide x 32.00 mm height, execution law. |
|
Paul Horn R220.3225.K2 Basic holder for cassette type 220 with shank 0 mm wide x 32.00 mm height, execution law. |
|
Paul Horn R220.3232.K2 Basic holder for cassette type 220 with shank 0 mm wide x 32.00 mm height, execution law. |
|
Paul Horn R220.TS40.K1 Basic holder for cassette type 220 |
|
Paul Horn R220.TS40.K2 Basic holder for cassette type 220 |
|
Paul Horn R220.TS50.K1 Basic holder for cassette type 220 |
|
Paul Horn R220.TS50.K2 Basic holder for cassette type 220 |
|
Paul Horn R220.TS63.K1 Basic holder for cassette type 220 |
|
Paul Horn R221.2020.04 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning (axial grooving from outer groove diameter 40.00 mm) for receiving inserts type 231 with a maximum penetratio |
|
Paul Horn R221.2020.05 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning (axial grooving from outer groove diameter 40.00 mm) for receiving inserts type 231 with a maximum penetratio |
|
Paul Horn R221.2020.07 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning (axial grooving from outer groove diameter 40.00 mm) for receiving inserts type 231 with a maximum penetratio |
|
Paul Horn R221.2020.09 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning (axial grooving from outer groove diameter 40.00 mm) for receiving inserts type 231 with a maximum penetratio |
|
Paul Horn R221.2525.04 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning (axial grooving from outer groove diameter 40.00 mm) for receiving inserts type 231 with a maximum penetration |
|
Paul Horn R221.2525.05 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning (axial grooving from outer groove diameter 40.00 mm) for receiving inserts type 231 with a maximum penetration |
|
Paul Horn R221.2525.07 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning (axial grooving from outer groove diameter 40.00 mm) for receiving inserts type 231 with a maximum penetration |
|
Paul Horn R221.2525.09 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning (axial grooving from outer groove diameter 40.00 mm) for receiving inserts type 231 with a maximum penetration |
|
Paul Horn R225.2525.04 Toolholder with shank 25 mm width x 25 mm height for the outside corner undercutting for receiving inserts type 229 at a cutting width of 3.0 to 5.0 mm, version right. |
|
Paul Horn R225.2525.05 Toolholder with shank 25 mm width x 25 mm height for the outside corner undercutting for receiving inserts type 229 at a cutting width of 5.1 to 6.0 mm, version right. |
|
Paul Horn R226.1616.03 Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and of clamping range 3.0 - 4.0 mm, ve |
|
Paul Horn R226.1616.04 Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and of clamping range 4,0 - 5,0 mm, ve |
|
Paul Horn R226.2020.0.03.IK Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 25 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R226.2020.0.04.IK Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 25 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R226.2020.0.05.IK Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 25 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R226.2020.03 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and of clamping range 3.0 - 4.0 mm, |
|
Paul Horn R226.2020.04 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and of clamping range 4,0 - 5,0 mm, |
|
Paul Horn R226.2020.05 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and of clamping range from 5.1 to 6. |
|
Paul Horn R226.2020.2.03.IK Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 25 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R226.2020.2.04.IK Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 25 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R226.2020.2.05.IK Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 25 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R226.2525.0.03.IK Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 25 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R226.2525.0.04.IK Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 25 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R226.2525.0.05.IK Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 25 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R226.2525.03 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and of clamping range 3.0 - 4.0 mm, v |
|
Paul Horn R226.2525.04 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and of clamping range 4,0 - 5,0 mm, v |
|
Paul Horn R226.2525.05 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and of clamping range from 5.1 to 6.0 |
|
Paul Horn R226.2525.07 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and of clamping range from 6.1 to 8.0 |
|
Paul Horn R226.2525.08 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and of clamping range from 7.6 to 8.0 |
|
Paul Horn R226.2525.09 Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and of clamping range from 8.1 to 10. |
|
Paul Horn R226.2525.2.03.IK Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 25 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R226.2525.2.04.IK Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 25 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R226.2525.2.05.IK Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 229 with a maximum cutting depth of 25 mm and an area of ​​tension 0 mm, version right |
|
Paul Horn R226.2608.03 Toolholder as Abstechschwert with shank 8:00 mm wide x 26.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and an area of ​​t |
|
Paul Horn R226.2608.04 Toolholder as Abstechschwert with shank 8:00 mm wide x 26.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and an area of ​​t |
|
Paul Horn R226.3208.03 Toolholder as Abstechschwert with shank 8:00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and an area of ​​t |
|
Paul Horn R226.3208.04 Toolholder as Abstechschwert with shank 8:00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and an area of ​​t |
|
Paul Horn R226.3225.03 Tool holders with shank 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and of clamping range 3.0 - 4.0 mm, v |
|
Paul Horn R226.3225.04 Tool holders with shank 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and of clamping range 4,0 - 5,0 mm, v |
|
Paul Horn R226.3225.05 Tool holders with shank 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and of clamping range from 5.1 to 6.0 |
|
Paul Horn R226.3225.07 Tool holders with shank 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and of clamping range from 6.1 to 8.0 |
|
Paul Horn R226.3225.08 Tool holders with shank 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and of clamping range from 7.6 to 8.0 |
|
Paul Horn R226.3225.09 Tool holders with shank 25.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 25.00 mm and of clamping range from 8.1 to 10. |
|
Paul Horn R226.F.2525.06.IK Toolholder with shank 25 mm wide x 25.00 mm height for external grooving and turning, for receiving inserts Type 229 with a maximum penetration depth of 21.5 mm, version right. |
|
Paul Horn R226.F.2525.08.IK Toolholder with shank 25 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 21.5 mm and an area of ​​tension 0 mm, version |
|
Paul Horn R226.F.2532.08 Toolholder with shank 32 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 229 with a maximum penetration depth 21.5 mm and an area of ​​tension 0 mm, version |
|
Paul Horn R228.2020.04 Toolholder with shank 20 mm width x 20 mm height for external grooving and turning (axial grooving from outer groove diameter 40 mm) for receiving inserts type 231 with a maximum penetration depth of |
|
Paul Horn R228.2020.05 Toolholder with shank 20 mm width x 20 mm height for external grooving and turning (axial grooving from outer groove diameter 40 mm) for receiving inserts type 231 with a maximum penetration depth of |
|
Paul Horn R228.2020.07 Toolholder with shank 20 mm width x 20 mm height for external grooving and turning (axial grooving from outer groove diameter 40 mm) for receiving inserts type 231 with a maximum penetration depth of |
|
Paul Horn R228.2020.09 Toolholder with shank 20 mm width x 20 mm height for external grooving and turning (axial grooving from outer groove diameter 40 mm) for receiving inserts type 231 with a maximum penetration depth of |
|
Paul Horn R228.2525.04 Toolholder with shank 25 mm width x 25 mm height for external grooving and turning (axial grooving from outer groove diameter 40 mm) for receiving inserts type 231 with a maximum penetration depth of |
|
Paul Horn R228.2525.05 Toolholder with shank 25 mm width x 25 mm height for external grooving and turning (axial grooving from outer groove diameter 40 mm) for receiving inserts type 231 with a maximum penetration depth of |
|
Paul Horn R228.2525.09 Toolholder with shank 25 mm width x 25 mm height for external grooving and turning (axial grooving from outer groove diameter 40 mm) for receiving inserts type 231 with a maximum penetration depth of |
|
Paul Horn R229.0610.01 TN35 The indexable insert with part profile is suitable for threading metric external threads with a pitch of 1 mm. |
|
Paul Horn R229.0610.02 TN35 The indexable insert full profile is suitable for threading metric external threads with a pitch of 1 mm. |
|
Paul Horn R229.0712.01 TN35 The indexable insert with part profile is suitable for threading metric external threads with a pitch of 1.25mm. |
|
Paul Horn R229.0712.02 TN35 The indexable insert full profile is suitable for threading metric external threads with a pitch of 1.25mm. |
|
Paul Horn R229.0915.01 TN35 The indexable insert with part profile is suitable for threading metric external threads with a pitch of 1.5 mm. |
|
Paul Horn R229.0915.02 TN35 The indexable insert full profile is suitable for threading metric external threads with a pitch of 1.5 mm. |
|
Paul Horn R229.1017.01 TN35 The indexable insert with part profile is suitable for threading metric external threads with a pitch of 1.75 mm. |
|
Paul Horn R229.1017.02 TN35 The indexable insert full profile is suitable for threading metric external threads with a pitch of 1.75 mm. |
|
Paul Horn R229.1220.01 TN35 The indexable insert with part profile is suitable for threading metric external threads with a pitch of 2 mm. |
|
Paul Horn R229.1220.02 TN35 The indexable insert full profile is suitable for threading metric external threads with a pitch of 2 mm. |
|
Paul Horn R229.1525.01 TN35 The indexable insert with part profile is suitable for threading metric external threads with a pitch of 2.5 mm. |
|
Paul Horn R229.1525.02 TN35 The indexable insert full profile is suitable for threading metric external threads with a pitch of 2.5 mm. |
|
Paul Horn R229.3040.HA50.12 AS65 The insert with a cutting width of 3 mm is suitable for grooving up to 4 mm depth. |
|
Paul Horn R229.4040.HA50.12 AS65 The insert with a cutting width of 4 mm is suitable for grooving up to 4 mm depth. |
|
Paul Horn R229.5300.31 AS62 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn R229.5300.31 MG12 Indexable insert suitable by Abstechschräge of 5 ° to butzenarmen parting, the cutting width is 3 mm with a possible groove depth up to 25 mm, version right. |
|
Paul Horn R229.5300.31 TC92 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn R229.5300.31 TI25 Indexable insert suitable by Abstechschräge of 5 ° to butzenarmen parting, the cutting width is 3 mm with a possible groove depth up to 25 mm, version right. |
|
Paul Horn R229.5300.31 TN32 Indexable insert is suitable by the Abstechschräge of 5 ° to butzenarmen parting, the cutting width is 3 mm with a possible groove depth up to 25 mm, version right. |
|
Paul Horn R229.5300.31 TN35 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn R230.0020.01 Toolholder with shaft diameter 20.00 mm for internal grooving and turning with the smallest bore diameter 20.00 mm for receiving inserts Type 217 with a maximum penetration depth of 3.00mm and a clamp |
|
Paul Horn R230.0020.02 Toolholder with shaft diameter 20.00 mm for internal grooving and turning with the smallest bore diameter 20.00 mm for receiving inserts Type 217 with a maximum penetration depth of 3.00mm and a clamp |
|
Paul Horn R230.0020.03 Toolholder with shaft diameter 20.00 mm for internal grooving and turning with the smallest bore diameter 20.00 mm for receiving inserts Type 217 with a maximum penetration depth of 3.00mm and a clamp |
|
Paul Horn R230.0020.04 Toolholder with shaft diameter 20.00 mm for internal grooving and turning with the smallest bore diameter 20.00 mm for receiving inserts Type 217 with a maximum penetration depth of 3.00mm and a clamp |
|
Paul Horn R231.0250.10 P20 Indexable insert with a cutting width w = 2.50 mm and maximum cutting depth of tmax = 11.00 mm is suitable for penetration of inner and outer contours. |
|
Paul Horn R231.0300.10 P20 The indexable insert with a cutting width of 3 mm is suitable for grooving of the inner and outer contours with up to 11 mm depth. |
|
Paul Horn R231.4030.32 TN35 The indexable insert with a cutting width of 3 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth. |
|
Paul Horn R231.4040.32 TN35 The indexable insert with a cutting width of 4 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth. |
|
Paul Horn R231.4050.34 TN35 The indexable insert with a cutting width of 5 mm is suitable for grooving of the inner and outer contours with up to 8 mm depth. |
|
Paul Horn R232.1212.02 Quick clamp holder for installation purposes for receiving inserts Type 217, clamping range from 1.7 to 2.7 mm, from bore diameter 40.00 mm, version right. |
|
Paul Horn R232.1212.03 Quick clamp holder for installation purposes for receiving inserts Type 217, clamping range from 2.7 to 3.7 mm, from bore diameter 40.00 mm, version right. |
|
Paul Horn R232.1212.04 Quick clamp holder for installation purposes for receiving inserts Type 217, clamping range from 3.7 to 5.3 mm, from bore diameter 40.00 mm, version right. |
|
Paul Horn R233.0020.01 Toolholder with shaft diameter 20.00 mm for internal grooving and turning with the smallest bore diameter 20.00 mm for receiving inserts Type 217 with a maximum penetration depth of 3.00mm and a clamp |
|
Paul Horn R233.0020.02 Toolholder with shaft diameter 20.00 mm for internal grooving and turning with the smallest bore diameter 20.00 mm for receiving inserts Type 217 with a maximum penetration depth 3.00 mm and an area o |
|
Paul Horn R233.0020.03 Toolholder with shaft diameter 20.00 mm for internal grooving and turning with the smallest bore diameter 20.00 mm for receiving inserts Type 217 with a maximum penetration depth of 3.00mm and a clamp |
|
Paul Horn R233.0020.04 Toolholder with shaft diameter 20.00 mm for internal grooving and turning with the smallest bore diameter 20.00 mm for receiving inserts Type 217 with a maximum penetration depth of 3.00mm and a clamp |
|
Paul Horn R234.0020.03 Toolholder with shaft diameter 20.00 mm for internal grooving and turning with the smallest bore diameter 20.00 mm for receiving inserts Type 217 with a maximum penetration depth of 3.00mm and a clamp |
|
Paul Horn R235.0020.01 Toolholder with shaft diameter 20.00 mm for internal grooving and turning with the smallest bore diameter 20.00 mm for receiving inserts Type 217 with a maximum penetration depth of 3.00mm and a clamp |
|
Paul Horn R235.0020.02 Toolholder with shaft diameter 20.00 mm for internal grooving and turning with the smallest bore diameter 20.00 mm for receiving inserts Type 217 with a maximum penetration depth of 3.00mm and a clamp |
|
Paul Horn R235.0020.03 Toolholder with shaft diameter 20.00 mm for internal grooving and turning with the smallest bore diameter 20 mm for the insertion of inserts Type 217 with a maximum penetration depth of 3.00mm and a c |
|
Paul Horn R235.0020.04 Toolholder with shaft diameter 20.00 mm for internal grooving and turning with the smallest bore diameter 20 mm for the insertion of inserts Type 217 with a maximum penetration depth of 3.00mm and a c |
|
Paul Horn R240.1010.01 Toolholder with shaft 10:00 mm width x height mm 10:00 for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range 0,5 - 1,7 mm, ver |
|
Paul Horn R240.1010.02 Toolholder with shaft 10:00 mm width x height mm 10:00 for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 1.7 to 2.7 m |
|
Paul Horn R240.1010.03 Toolholder with shaft 10:00 mm width x height mm 10:00 for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 2.7 to 3.7 m |
|
Paul Horn R240.1010.04 Toolholder with shaft 10:00 mm width x height mm 10:00 for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 3.7 to 5.3 m |
|
Paul Horn R240.1212.01 Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range 0,5 - 1,7 mm, v |
|
Paul Horn R240.1212.02 Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 1.7 to 2.7 |
|
Paul Horn R240.1212.03 Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 2.7 to 3.7 |
|
Paul Horn R240.1212.04 Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 3.7 to 5.3 |
|
Paul Horn R240.1414.04 Tool holders with shank 14.00 mm Width x 14.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 3.7 to 5.3 |
|
Paul Horn R240.1616.01 Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range 0,5 - 1,7 mm, ver |
|
Paul Horn R240.1616.02 Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 1.7 to 2.7 m |
|
Paul Horn R240.1616.03 Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 2.7 to 3.7 m |
|
Paul Horn R240.1616.04 Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 3.7 to 5.3 m |
|
Paul Horn R240.2020.01 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range 0,5 - 1,7 mm, v |
|
Paul Horn R240.2020.02 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 1.7 to 2.7 |
|
Paul Horn R240.2020.03 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 2.7 to 3.7 |
|
Paul Horn R240.2020.04 Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 3.7 to 5.3 |
|
Paul Horn R245.0020.02 Toolholder with shaft diameter 20 mm for corner undercutting interior with the smallest bore diameter 20 mm for the insertion of inserts Type 217 with a clamping range from 1.7 to 2.7 mm, version righ |
|
Paul Horn R245.0020.03 Toolholder with shaft diameter 20 mm for corner undercutting interior with the smallest bore diameter 20 mm for the insertion of inserts Type 217 with a clamping range from 2.7 to 3.7 mm, version righ |
|
Paul Horn R245.0020.04 Toolholder with shaft diameter 20 mm for corner undercutting interior with the smallest bore diameter 20 mm for the insertion of inserts Type 217 with a clamping range from 3.7 to 5.3 mm, version righ |
|
Paul Horn R245.0032.02 Toolholder with shaft diameter 32 mm for corner undercutting interior with the smallest bore diameter 31 mm for the insertion of inserts Type 217 with a clamping range from 1.7 to 2.7 mm, version righ |
|
Paul Horn R245.0032.03 Toolholder with shaft diameter 32 mm for corner undercutting interior with the smallest bore diameter 31 mm for the insertion of inserts Type 217 with a clamping range from 2.7 to 3.7 mm, version righ |
|
Paul Horn R245.0032.04 Toolholder with shaft diameter 32 mm for corner undercutting interior with the smallest bore diameter 31 mm for the insertion of inserts Type 217 with a clamping range from 3.7 to 5.3 mm, version righ |
|
Paul Horn R248.1212.01 Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range 0,5 - 1,7 mm, v |
|
Paul Horn R248.1212.02 Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 1.7 to 2.7 |
|
Paul Horn R250.0025.01 Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and a by clam |
|
Paul Horn R250.0025.02 Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R250.0025.03 Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R250.0025.04 Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R250.0032.01 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and a by clam |
|
Paul Horn R250.0032.02 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R250.0032.03 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R250.0032.04 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R253.0025.01 Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and a by clam |
|
Paul Horn R253.0025.02 Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R253.0025.03 Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R253.0025.04 Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R253.0032.01 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and a by clam |
|
Paul Horn R253.0032.02 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R253.0032.03 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R253.0032.04 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R254.0025.01 Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and a by clam |
|
Paul Horn R254.0025.02 Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R254.0025.03 Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R254.0032.01 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and a by clam |
|
Paul Horn R254.0032.03 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R254.0032.04 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R255.0025.01 Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and a by clam |
|
Paul Horn R255.0025.02 Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R255.0025.03 Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25 mm for the insertion of inserts Type 217 with a maximum penetration depth 4.70 mm and an ar |
|
Paul Horn R255.0025.04 Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25 mm for the insertion of inserts Type 217 with a maximum penetration depth 4.70 mm and an ar |
|
Paul Horn R255.0032.01 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and a by clam |
|
Paul Horn R255.0032.02 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R255.0032.03 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R255.0032.04 Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o |
|
Paul Horn R257.2222.05 Quick clamp holder for installation purposes for receiving inserts Type 229, clamping range from 5.1 to 6.0 mm, from bore diameter 80.00 mm, version right. |
|
Paul Horn R264.0150.P0 TI25 Indexable insert with a cutting width of 1.5 mm, Parisian cut and maximum cutting depth of 16 mm is suitable for grooving and turning of outer contours. |
|
Paul Horn R264.0150.P0 TN35 Indexable insert with a cutting width of 1.5 mm, Parisian cut and maximum cutting depth of 16 mm is suitable for grooving and turning of outer contours. |
|
Paul Horn R264.0200.P0 MG12 The indexable insert with a cutting width of 2 mm is suitable for grooving and turning of outer contours with up to 16 mm depth. |
|
Paul Horn R264.0200.P0 TI25 The indexable insert with a cutting width of 2 mm is suitable for grooving and turning of outer contours with up to 16 mm depth. |
|
Paul Horn R264.0200.P0 TN35 Indexable insert with a cutting width of 2 mm, Parisian cut and maximum cutting depth of 16 mm is suitable for grooving and turning of outer contours. |
|
Paul Horn R264.0200.P2 TN35 The indexable insert with a cutting width of 2 mm is suitable for grooving and turning of outer contours with up to 16 mm depth. |
|
Paul Horn R264.0250.P0 MG12 The indexable insert with a cutting width of 2.5 mm is suitable for grooving and turning of outer contours with up to 16 mm depth. |
|
Paul Horn R264.0250.P0 TI25 Indexable insert with a cutting width of 2.5 mm, Parisian cut and maximum cutting depth of 16 mm is suitable for grooving and turning of outer contours. |
|
Paul Horn R264.0250.P0 TN35 Indexable insert with a cutting width of 2.5 mm, Parisian cut and maximum cutting depth of 16 mm is suitable for grooving and turning of outer contours. |
|
Paul Horn R264.0250.P2 TN35 The indexable insert with a cutting width of 2.5 mm is suitable for grooving and turning of outer contours with up to 16 mm depth. |
|
Paul Horn R264.0300.P0 MG12 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of outer contours with up to 16 mm depth. |
|
Paul Horn R264.0300.P0 TI25 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of outer contours with up to 16 mm depth. |
|
Paul Horn R264.0300.P0 TN35 Indexable insert with a cutting width of 3 mm, Parisian cut and maximum cutting depth of 16 mm is suitable for grooving and turning of outer contours. |
|
Paul Horn R264.0300.P2 TN35 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of outer contours with up to 16 mm depth. |
|
Paul Horn R264.0305.02 TF45 Indexable insert with a pitch of 0.5 mm and maximum cutting depth 0.31 mm is suitable for chasing of metric external threads. |
|
Paul Horn R264.0306.02 TF45 Indexable insert with a pitch of 0.6 mm and maximum cutting depth 0.37 mm is suitable for chasing of metric external threads. |
|
Paul Horn R264.0307.02 TF45 Indexable insert with a pitch of 0.7 mm and maximum cutting depth 0.43 mm is suitable for chasing of metric external threads. |
|
Paul Horn R264.0407.02 TF45 Indexable insert with a pitch of 0.75 mm and maximum cutting depth of 0.46mm suitable for chasing of metric external threads. |
|
Paul Horn R264.0408.02 TF45 Indexable insert with a pitch of 0.8 mm and maximum cutting depth 0.49 mm is suitable for chasing of metric external threads. |
|
Paul Horn R264.0610.02 TF45 Indexable insert with a pitch of 1 mm and maximum cutting depth of 0.61 mm is suitable for chasing of metric external threads. |
