|
Paul Horn RS100.0530.F2 TC92 The insert with a cutting width of 3 mm is suitable for tapping. |
|
Paul Horn RS100.0530.F2 TC93 Insert to butzenarmen parting with a cutting width of 3 mm and a corner radius of 0.2 mm, with geometry F and Abstechschräge 5 °, execution law. |
|
Paul Horn RS100.0530.F2 TF43 Insert for butzenarmen parting with a cutting width of 3 mm and a corner radius of 0.2 mm, with geometry F and Abstechschräge 5 °, execution law. |
|
Paul Horn RS100.0530.F2 TF45 Insert for butzenarmen parting with a cutting width of 3 mm and a corner radius of 0.2 mm, with geometry F and Abstechschräge 5 °, execution law. |
|
Paul Horn RS100.0530.F2 TF46 Insert for butzenarmen parting with a cutting width of 3 mm and a corner radius of 0.2 mm, with geometry F and Abstechschräge 5 °, execution law. |
|
Paul Horn RS100.0530.F2 TI22 Insert RS100.0530.F2 Ti22 to butzenarmen parting with a cutting width of 3 mm and a corner radius of 0.2 mm, with geometry F and Abstechschräge 5 °, execution law. |
|
Paul Horn RS100.0540.E2 TC93 Insert to butzenarmen parting with a cutting width of 4 mm and a corner radius of 0.2 mm, with geometry E and Abstechschräge 5 °, execution law. |
|
Paul Horn RS100.0540.E2 TF43 Insert for butzenarmen parting with a cutting width of 4 mm and a corner radius of 0.2 mm, with geometry E and Abstechschräge 5 °, execution law. |
|
Paul Horn RS100.0540.E2 TF45 Insert for butzenarmen parting with a cutting width of 4 mm and a corner radius of 0.2 mm, with geometry E and Abstechschräge 5 °, execution law. |
|
Paul Horn RS100.0540.E2 TF46 Insert for butzenarmen parting with a cutting width of 4 mm and a corner radius of 0.2 mm, with geometry E and Abstechschräge 5 °, execution law. |
|
Paul Horn RS100.0540.E2 TI22 Insert RS100.0540.E2 Ti22 to butzenarmen parting with a cutting width of 4 mm and a corner radius of 0.2 mm, with geometry E and Abstechschräge 5 °, execution law. |
|
Paul Horn RS100.0540.EN2 ALX3 The insert RS100.0540.EN2 AlX3 with a cutting width of 4 mm is suitable for tapping. |
|
Paul Horn RS100.0540.F2 TF43 Insert for butzenarmen parting with a cutting width of 4 mm and a corner radius of 0.2 mm, with geometry F and Abstechschräge 5 °, execution law. |
|
Paul Horn RS100.0540.F2 TF45 Insert for butzenarmen parting with a cutting width of 4 mm and a corner radius of 0.2 mm, with geometry F and Abstechschräge 5 °, execution law. |
|
Paul Horn RS100.1520.FY0 AS45 Insert for butzenarmen parting with a cutting width of 2 mm with geometry and FY Abstechschräge 15 °, execution law. |
|
Paul Horn RS100.1530.FY0 AS45 Insert for butzenarmen parting with a cutting width of 3 mm with geometry and FY Abstechschräge 15 °, execution law. |
|
Paul Horn RS108.0100.D1 TH35 Insert deep grooves for insertion from bore diameter 8 mm with 1 mm width, corner radius 0.1 mm and a maximum of 1 mm. |
|
Paul Horn RS108.0150.D1 TH35 Insert deep grooves for insertion from bore diameter 8 mm with 1.5 mm width, corner radius 0.1 mm and a maximum of 1 mm. |
|
Paul Horn RS108.0200.D2 TH35 Insert deep grooves for insertion from bore diameter 8 mm with 2 mm width, corner radius 0.2 mm and a maximum of 1 mm. |
|
Paul Horn RS108.1846.R2 TH35 Insert for internal turning and copying from bore diameter 7.8 mm, with a corner radius of 0.2 mm. |
|
Paul Horn RS108.1846.R4 TH35 Insert for internal turning and copying from bore diameter 7.8 mm, with a corner radius of 0.4 mm. |
|
Paul Horn RS10P.0100.1.D1 TH35 Insert for the cutting of grooves from bore diameter 9 mm 1 mm width, corner radius 0.1 mm and a maximum depth of 2 mm. |
|
Paul Horn RS10P.0150.1.D1 TH35 Insert for the cutting of grooves from bore diameter 9 mm 1.5 mm width, corner radius 0.1 mm and a maximum depth of 2 mm. |
|
Paul Horn RS10P.0150.2.D1 TH35 Insert deep for the cutting of grooves from bore diameter 10 mm 1.5 mm width, corner radius 0.1 mm and a maximum of 3 mm. |
|
Paul Horn RS10P.0200.1.D2 TH35 Insert for the cutting of grooves from bore diameter 9 mm 2 mm width, corner radius 0.2 mm and a maximum depth of 2 mm. |
|
Paul Horn RS10P.0200.2.D2 TH35 Insert for the cutting of grooves from bore diameter 10 mm 2 mm width, corner radius 0.2 mm and a maximum depth of 3 mm. |
|
Paul Horn RS10P.1854.R2 TH35 Insert for internal turning and copying from bore diameter 8.8 mm with a corner radius of 0.2 mm. |
|
Paul Horn RS10P.1854.R4 TH35 Insert for internal turning and copying from bore diameter 8.8 mm with a corner radius of 0.4 mm. |
|
Paul Horn RS111.0150.D1 TH35 Insert for the cutting of grooves to from bore diameter 11 mm with 1.5 mm width (nose radius 0.1 mm) and a maximum of 2.3 mm deep. |
|
Paul Horn RS111.0200.D2 TH35 Insert deep for the cutting of grooves to from bore diameter 11 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 2.3 mm. |
|
Paul Horn RS111.0250.D2 TH35 Insert for the cutting of grooves to from bore diameter 11 mm with width 2.5 mm (corner radius 0.2 mm) and a maximum of 2.3 mm deep. |
|
Paul Horn RS111.1867.R2 TH35 Insert for internal turning and copying from bore diameter 11 mm with a corner radius of 0.2 mm. |
|
Paul Horn RS111.1867.R4 TH35 Insert for internal turning and copying from bore diameter 11 mm with a corner radius of 0.4 mm. |
|
Paul Horn RS114.0200.1.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 16.5 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 6.5 mm deep. |
|
Paul Horn RS114.0200.D2 TF45 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn RS114.0200.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn RS114.0200.D2 TN35 Insert to Inneneinstechen of grooves from bore diameter 14 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn RS114.0250.1.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 16.5 mm with 2.5 mm width (nose radius 0.2 mm) and a maximum of 6.5 mm deep. |
|
Paul Horn RS114.0250.D2 TF45 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 2.5 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn RS114.0250.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 2.5 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn RS114.0250.D2 TN35 Insert to Inneneinstechen of grooves from bore diameter 14 mm with 2.5 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn RS114.0300.1.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 16.5 mm with 3 mm width (nose radius 0.2 mm) and a maximum of 6.5 mm deep. |
|
Paul Horn RS114.0300.D2 TF45 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 3 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn RS114.0300.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 14 mm with 3 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn RS114.0300.D2 TN35 Insert to Inneneinstechen of grooves from bore diameter 14 mm with 3 mm width (nose radius 0.2 mm) and a maximum of 4 mm deep. |
|
Paul Horn RS114.1890.R2 TH35 Insert for internal turning and copying from bore diameter 13.8 mm with a corner radius of 0.2 mm. |
|
Paul Horn RS114.1890.R4 TH35 Insert for internal turning and copying from bore diameter 13.8 mm with a corner radius of 0.4 mm. |
|
Paul Horn RS116.0200.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 16 mm with 2 mm width (nose radius 0.2 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn RS116.0250.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 16 mm with width 2.5 mm (corner radius 0.2 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn RS116.0300.D2 TH35 Insert for Inneneinstechen of grooves from bore diameter 16 mm with 3 mm width (nose radius 0.2 mm) and a maximum of 4.3 mm deep. |
|
Paul Horn RS116.1897.R2 TH35 Insert for internal turning and copying from bore diameter 15.5 mm with a corner radius of 0.2 mm. |
|
Paul Horn RS116.1897.R4 TH35 Insert for internal turning and copying from bore diameter 15.5 mm with a corner radius of 0.4 mm. |
|
Paul Horn RS117.300.00.A0.10 MD10 The insert with a cutting width of 3.5 mm is suitable for polish turning of internal and external contours. |
|
Paul Horn RS117.300.00.K0.10 MD10 The insert with a cutting width of 3.5 mm is suitable for polish turning of internal and external contours. |
|
Paul Horn RS117.300.00.M0.10 MD10 The insert with a cutting width of 3.5 mm is suitable for polish turning of internal and external contours. |
|
Paul Horn RS11P.0150.1.D1 TH35 The insert with a cutting width of 1.5 mm is suitable for penetration of inner contours with up to 2.5 mm deep. |
|
Paul Horn RS11P.0150.2.D1 TH35 The insert with a cutting width of 1.5 mm is suitable for penetration of inner contours with up to 3.5 mm deep. |
|
Paul Horn RS11P.0200.1.D2 TH35 The insert with a cutting width of 2 mm is suitable for penetration of inner contours with depths up to 2.5 mm. |
|
Paul Horn RS11P.0200.2.D2 TH35 The insert with a cutting width of 2 mm is suitable for penetration of inner contours with up to 3.5 mm deep. |
|
Paul Horn RS11P.0250.1.D2 TH35 The insert with a cutting width of 2.5 mm is suitable for penetration of inner contours with depths up to 2.5 mm. |
|
Paul Horn RS11P.0250.2.D2 TH35 The insert with a cutting width of 2.5 mm is suitable for penetration of inner contours with up to 3.5 mm deep. |
|
Paul Horn RS11P.1859.R2 TH35 The insert suitable for bore-turning and grooving of inner contours. |
|
Paul Horn RS11P.1859.R4 TH35 The insert suitable for bore-turning and grooving of inner contours. |
|
Paul Horn RS123.0420.C0 TF45 Insert for butzenarmen parting with a cutting width of 2 mm, with geometry C0 and Abstechschräge 4 °, execution law. |
|
Paul Horn RS123.0420.C0 TI25 The insert with a cutting width of 2 mm is suitable for tapping up to 25 mm depth. |
|
Paul Horn RS123.0420.C0 TN35 Indexable insert TiN coated |
|
Paul Horn RS123.0420.C1 TI25 The insert with a cutting width of 2 mm is suitable for tapping up to 25 mm depth. |
|
Paul Horn RS123.0430.C0 TI25 Insert to butzenarmen parting with a cutting width of 3 mm, with geometry C0 and Abstechschräge 4 °, execution law. |
|
Paul Horn RS123.0820.C0 TN35 Insert to butzenarmen parting with a cutting width of 2 mm, with geometry C0 and Abstechschräge 8 °, execution law. |
|
Paul Horn RS123.0820.C1 TI25 The insert with a cutting width of 2 mm is suitable for tapping up to 25 mm depth. |
|
Paul Horn RS123.0830.C1 TF45 The insert with a cutting width of 3 mm is suitable for tapping up to 25 mm depth. |
|
Paul Horn RS123.1520.C0 TF45 The insert with a cutting width of 2 mm is suitable for tapping up to 25 mm depth. |
|
Paul Horn RS123.1520.C0 TN35 The insert with a cutting width of 2 mm is suitable for tapping up to 25 mm depth. |
|
Paul Horn RS18P.0200.1.D2 TH35 The insert with a cutting width of 2 mm is suitable for grooving of the inner edges up to 6 mm depth. |
|
Paul Horn RS18P.0200.2.D2 TH35 The insert with a cutting width of 2 mm is suitable for grooving of the inner edges up to 8 mm depth. |
|
Paul Horn RS18P.0250.1.D2 TH35 The insert with a cutting width of 2.5 mm is suitable for grooving of the inner edges up to 6 mm depth. |
|
Paul Horn RS18P.0250.2.D2 TH35 The insert with a cutting width of 2.5 mm is suitable for grooving of the inner edges up to 8 mm depth. |
|
Paul Horn RS18P.0300.1.D2 TH35 The insert with a cutting width of 3 mm is suitable for grooving of the inner edges up to 6 mm depth. |
|
Paul Horn RS18P.0300.2.D2 TH35 The insert with a cutting width of 3 mm is suitable for grooving of the inner edges up to 8 mm depth. |
|
Paul Horn RS18P.1815.R2 TH35 The insert suitable for bore-turning and turning inside contours. |
|
Paul Horn RS18P.1815.R4 TH35 The insert suitable for bore-turning and turning inside contours. |
|
Paul Horn RS223.0420.C0 TF45 Indexable insert TiAlN coated |
|
Paul Horn RS223.0420.C0 TI25 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS223.0420.C0 TN35 Indexable insert to butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 11 mm, with geometry C and 4 ° Abstechschräge, execution law. |
|
Paul Horn RS223.0420.C1 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS223.0420.C1 TI25 Indexable insert to butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 11 mm, with geometry C and 4 ° Abstechschräge, execution law. |
|
Paul Horn RS223.0420.C1 TN35 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS223.0425.C0 TI25 Indexable insert to butzenarmen parting with a cutting width of 2.5 mm and a maximum insertion depth of 11 mm, with geometry C and 4 ° Abstechschräge, execution law. |
|
Paul Horn RS223.0425.C0 TN35 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS223.0425.C1 TI25 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS223.0430.C0 TN35 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 11 mm, with geometry C and 4 ° Abstechschräge, execution law. |
|
Paul Horn RS223.0430.C1 TI25 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS223.0430.C1 TN35 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS223.0820.C0 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS223.0820.C0 TI25 Indexable insert to butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 11 mm, with geometry C and 8 ° Abstechschräge, execution law. |
|
Paul Horn RS223.0820.C0 TN35 Indexable insert to butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 11 mm, with geometry C and 8 ° Abstechschräge, execution law. |
|
Paul Horn RS223.0820.C1 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS223.0820.C1 TI25 Indexable insert to butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 11 mm, with geometry C and 8 ° Abstechschräge, execution law. |
|
Paul Horn RS223.0820.C1 TN35 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS223.0825.C0 TF45 Indexable insert for butzenarmen parting with a cutting width of 2.5 mm and a maximum insertion depth of 11 mm, with geometry C and 8 ° Abstechschräge, execution law. |
|
Paul Horn RS223.0825.C0 TI25 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS223.0825.C0 TN35 Indexable insert to butzenarmen parting with a cutting width of 2.5 mm and a maximum insertion depth of 11 mm, with geometry C and 8 ° Abstechschräge, execution law. |
|
Paul Horn RS223.0825.C1 TF45 Indexable insert for butzenarmen parting with a cutting width of 2.5 mm and a maximum insertion depth of 11 mm, with geometry C and 8 ° Abstechschräge, execution law. |
|
Paul Horn RS223.0825.C1 TI25 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS223.0830.C0 TF45 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS223.0830.C0 TN35 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 11 mm, with geometry C and 8 ° Abstechschräge, execution law. |
|
Paul Horn RS223.0830.C1 TF45 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS223.0830.C1 TI25 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 11 mm, with geometry C and 8 ° Abstechschräge, execution law. |
|
Paul Horn RS223.0830.C1 TN35 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS223.1520.C0 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS223.1520.C0 TI25 Indexable insert for grooving and parting with a cutting width of 2 mm and a maximum insertion depth of 11 mm, with geometry C and 15 ° Abstechschräge, execution law. |
|
Paul Horn RS223.1520.C0 TN35 Indexable insert for grooving and parting with a cutting width of 2 mm and a maximum insertion depth of 11 mm, with geometry C and 15 ° Abstechschräge, execution law. |
|
Paul Horn RS223.1520.C1 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS223.1520.C1 TI25 Indexable insert for grooving and parting with a cutting width of 2 mm and a maximum insertion depth of 11 mm, with geometry C and 15 ° Abstechschräge, execution law. |
|
Paul Horn RS223.1520.C1 TN35 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 11 mm depth. |
|
Paul Horn RS224.0305.02 TF45 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.5 mm. |
|
Paul Horn RS224.0407.02 TF45 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.75 mm. |
|
Paul Horn RS224.0520.C0 TF45 Indexable insert for butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 18 mm, with geometry C and Abstechschräge 5 °, execution law. |
|
Paul Horn RS224.0520.C0 TN35 Indexable insert to butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 18 mm, with geometry C and Abstechschräge 5 °, execution law. |
|
Paul Horn RS224.0520.C1 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0520.E2 AS62 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0520.F2 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0520.F2 TF46 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0525.C0 TF45 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0525.C0 TI25 Indexable insert to butzenarmen parting with a cutting width of 2.5 mm and a maximum insertion depth of 18 mm, with geometry C and Abstechschräge 5 °, execution law. |
|
Paul Horn RS224.0525.C0 TN35 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0525.C1 TF45 Indexable insert for butzenarmen parting with a cutting width of 2.5 mm and a maximum insertion depth of 18 mm, with geometry C and Abstechschräge 5 °, execution law. |
|
Paul Horn RS224.0525.C1 TN35 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0525.E2 AS62 The indexable insert with a cutting width of 2.5 mm is suitable for tapping. |
|
Paul Horn RS224.0525.F2 TF43 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0525.F2 TF45 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0530.C0 TC92 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0530.C0 TF45 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0530.C0 TN35 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 18 mm, with geometry C and Abstechschräge 5 °, execution law. |
|
Paul Horn RS224.0530.C1 TF45 Indexable insert for butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 18 mm, with geometry C and Abstechschräge 5 °, execution law. |
|
Paul Horn RS224.0530.C1 TN35 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0530.E2 AS62 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0530.E2 TC92 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0530.E2 TC93 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0530.E2 TF43 Indexable insert for butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 18 mm, with geometry E and Abstechschräge 5 °, execution law. |
|
Paul Horn RS224.0530.E2 TF45 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0530.F2 TF43 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0530.F2 TF45 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0530.F2 TI22 Indexable insert RS224.0530.F2 Ti22 to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 18 mm, with geometry F and Abstechschräge 5 °, execution law. |
|
Paul Horn RS224.0610.02 TF45 The indexable insert full profile is suitable for threading metric threads with a pitch of 1 mm. |
|
Paul Horn RS224.0712.02 TF45 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.25mm. |
|
Paul Horn RS224.0820.C0 TF45 Indexable insert for butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 18 mm, with geometry C and 8 ° Abstechschräge, execution law. |
|
Paul Horn RS224.0820.C0 TN35 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0820.C1 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0825.C0 TF45 Indexable insert for butzenarmen parting with a cutting width of 2.5 mm and a maximum insertion depth of 18 mm, with geometry C and 8 ° Abstechschräge, execution law. |
|
Paul Horn RS224.0825.C0 TN35 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0825.C1 TF45 Indexable insert for butzenarmen parting with a cutting width of 2.5 mm and a maximum insertion depth of 18 mm, with geometry C and 8 ° Abstechschräge, execution law. |
|
Paul Horn RS224.0830.C0 TF45 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0830.C0 TN35 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0830.C1 TF45 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0830.C1 TN35 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.0915.02 TF45 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.5 mm. |
|
Paul Horn RS224.1017.02 TF45 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.75 mm. |
|
Paul Horn RS224.1220.02 TF45 The indexable insert full profile is suitable for threading metric threads with a pitch of 2 mm. |
|
Paul Horn RS224.1520.C0 TC92 Indexable insert to butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 18 mm, with geometry C and 15 ° Abstechschräge, execution law. |
|
Paul Horn RS224.1520.C0 TF45 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.1520.C0 TN35 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS224.1520.C1 TF45 Indexable insert for butzenarmen parting with a cutting width of 2 mm and a maximum insertion depth of 18 mm, with geometry C and 15 ° Abstechschräge, execution law. |
|
Paul Horn RS224.1520.C1 TN35 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 18 mm depth. |
|
Paul Horn RS229.0530.32 AS62 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn RS229.0530.32 TC92 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with 30 geometry and Abstechschräge 5 °, execution law. |
|
Paul Horn RS229.0530.32 TF45 Indexable insert for butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with 30 geometry and Abstechschräge 5 °, execution law. |
|
Paul Horn RS229.0530.32 TI25 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn RS229.0530.32 TN32 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with 30 geometry and Abstechschräge 5 °, execution law. |
|
Paul Horn RS229.0530.32 TN35 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn RS229.0530.C0 TF45 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn RS229.0530.C0 TI25 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn RS229.0530.C0 TN35 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with geometry C and Abstechschräge 5 °, execution law. |
|
Paul Horn RS229.0530.C1 TI25 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn RS229.0530.C1 TN35 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with geometry C and Abstechschräge 5 °, execution law. |
|
Paul Horn RS229.0540.32 AS62 The indexable insert with a cutting width of 4 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn RS229.0540.32 TF45 Indexable insert for butzenarmen parting with a cutting width of 4 mm and a maximum insertion depth of 25 mm, with 30 geometry and Abstechschräge 5 °, execution law. |
|
Paul Horn RS229.0540.32 TI25 The indexable insert with a cutting width of 4 mm is suitable for tapping inner and outer contours with up to 25 mm depth. |
|
Paul Horn RS229.0540.32 TN32 Indexable insert to butzenarmen parting with a cutting width of 4 mm and a maximum insertion depth of 25 mm, with 30 geometry and Abstechschräge 5 °, execution law. |
|
Paul Horn RS229.0540.C0 TI25 Indexable insert to butzenarmen parting with a cutting width of 4 mm and a maximum insertion depth of 25 mm, with geometry C and Abstechschräge 5 °, execution law. |
|
Paul Horn RS229.0540.C0 TN35 The indexable insert with a cutting width of 4 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn RS229.0540.C1 TC92 Indexable insert multi-layer coated |
|
Paul Horn RS229.0540.C1 TI25 Indexable insert to butzenarmen parting with a cutting width of 4 mm and a maximum insertion depth of 25 mm, with geometry C and Abstechschräge 5 °, execution law. |
|
Paul Horn RS229.0540.C1 TN35 The indexable insert with a cutting width of 4 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn RS229.0830.C0 TC92 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn RS229.0830.C0 TF45 Indexable insert for butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with geometry C and 8 ° Abstechschräge, execution law. |
|
Paul Horn RS229.0830.C0 TI25 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with geometry C and 8 ° Abstechschräge, execution law. |
|
Paul Horn RS229.0830.C0 TN35 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn RS229.0830.C1 TF45 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn RS229.0830.C1 TI25 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 25 mm, with geometry C and 8 ° Abstechschräge, execution law. |
|
Paul Horn RS229.0830.C1 TN35 The indexable insert with a cutting width of 3 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn RS229.0840.C0 TC92 The indexable insert with a cutting width of 4 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn RS229.0840.C0 TI25 Indexable insert to butzenarmen parting with a cutting width of 4 mm and a maximum insertion depth of 25 mm, with geometry C and 8 ° Abstechschräge, execution law. |
|
Paul Horn RS229.0840.C0 TN35 Indexable insert to butzenarmen parting with a cutting width of 4 mm and a maximum insertion depth of 25 mm, with geometry C and 8 ° Abstechschräge, execution law. |
|
Paul Horn RS229.0840.C1 TC92 Indexable insert to butzenarmen parting with a cutting width of 4 mm and a maximum insertion depth of 25 mm, with geometry C and 8 ° Abstechschräge, execution law. |
|
Paul Horn RS229.0840.C1 TN35 The indexable insert with a cutting width of 4 mm is suitable for parting with up to 25 mm depth. |
|
Paul Horn RS274.0005.01.SF AC25 Indexable insert for Einstechen- and turning with a cutting width of 0.5 mm and maximum piercing depth of 1 mm, Ој-Finisch, execution law. |
|
Paul Horn RS274.0010.02.SF AC25 Indexable insert for Einstechen- and turning with a cutting width of 1.0 mm and maximum piercing depth of 2.0 mm, Ој-Finisch, execution law. |
|
Paul Horn RS274.0012.02.SF AC25 Indexable insert for Einstechen- and turning with a cutting width of 1.2 mm and maximum piercing depth of 2.0 mm, Ој-Finisch, execution law. |
|
Paul Horn RS274.0015.03.SF AC25 Indexable insert for Einstechen- and turning with a cutting width of 1.5 mm and maximum piercing depth of 3.0 mm, Ој-Finisch, execution law. |
|
Paul Horn RS274.0020.03.SF AC25 Indexable insert for Einstechen- and turning with a cutting width of 2 mm and maximum piercing depth of 3 mm, Ој-Finisch, execution law. |
|
Paul Horn RS274.0035.04.20 TH35 The indexable insert suitable for longitudinal turning of outer contours. |
|
Paul Horn RS274.0035.04.20.E TH35 The indexable insert suitable for longitudinal turning of outer contours. |
|
Paul Horn RS274.0050.01.10 TH35 The indexable insert with a cutting width of 0.5 mm is suitable for parting and grooving of outer contours with up to 1.5 mm deep. |
|
Paul Horn RS274.0050.01.10.E TH35 The indexable insert with a cutting width of 0.5 mm is suitable for parting and grooving of outer contours with up to 1.5 mm deep. |
|
Paul Horn RS274.0050.01.20 TH35 The indexable insert with a cutting width of 0.5 mm is suitable for parting and grooving of outer contours with up to 1.5 mm deep. |
|
Paul Horn RS274.0050.01.20.E TH35 The indexable insert with a cutting width of 0.5 mm is suitable for parting and grooving of outer contours with up to 1.5 mm deep. |
|
Paul Horn RS274.0050.01.M0 TH35 The indexable insert with a cutting width of 0.5 mm is suitable for parting and grooving of outer contours with up to 1.5 mm deep. |
|
Paul Horn RS274.0050.01.M0.E TH35 The indexable insert with a cutting width of 0.5 mm is suitable for parting and grooving of outer contours with up to 1.5 mm deep. |
|
Paul Horn RS274.0050.P0 AN25 The indexable insert with a cutting width of 0.5 mm is suitable for grooving and turning of outer contours with up to 1 mm depth. |
|
Paul Horn RS274.0055.04.20 TH35 The indexable insert suitable for longitudinal turning of outer contours. |
|
Paul Horn RS274.0055.04.20.E TH35 The indexable insert suitable for longitudinal turning of outer contours. |
|
Paul Horn RS274.0055.24.20 TH35 The indexable insert suitable for longitudinal turning of outer contours. |
|
Paul Horn RS274.0060.04.10 TH35 The indexable insert suitable for reverse rotation of outer contours. |
|
Paul Horn RS274.0060.04.10.E TH35 The indexable insert suitable for reverse rotation of outer contours. |
|
Paul Horn RS274.0070.02.10 TH35 The indexable insert with a cutting width of 0.7 mm is suitable for parting and grooving of outer contours with up to 2 mm depth. |
|
Paul Horn RS274.0070.02.10.E TH35 The indexable insert with a cutting width of 0.7 mm is suitable for parting and grooving of outer contours with up to 2 mm depth. |
|
Paul Horn RS274.0070.02.20 TH35 The indexable insert with a cutting width of 0.7 mm is suitable for parting and grooving of outer contours with up to 2 mm depth. |
|
Paul Horn RS274.0070.02.20.E TH35 The indexable insert with a cutting width of 0.7 mm is suitable for parting and grooving of outer contours with up to 2 mm depth. |
|
Paul Horn RS274.0070.02.M0 TH35 The indexable insert with a cutting width of 0.7 mm is suitable for parting and grooving of outer contours with up to 2 mm depth. |
|
Paul Horn RS274.0070.02.M0.E TH35 The indexable insert with a cutting width of 0.7 mm is suitable for parting and grooving of outer contours with up to 2 mm depth. |
|
Paul Horn RS274.0080.03.10 TH35 The indexable insert with a cutting width of 0.8 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0080.03.10.E TH35 The indexable insert with a cutting width of 0.8 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0080.03.20 TH35 The indexable insert with a cutting width of 0.8 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0080.03.20.E TH35 The indexable insert with a cutting width of 0.8 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0080.03.M0 TH35 The indexable insert with a cutting width of 0.8 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0080.03.M0.E TH35 The indexable insert with a cutting width of 0.8 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0100.03.10 TH35 The indexable insert with a cutting width of 1 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0100.03.10.E TH35 The indexable insert with a cutting width of 1 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0100.03.20 TH35 The indexable insert with a cutting width of 1 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0100.03.20.E TH35 The indexable insert with a cutting width of 1 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0100.03.M0 TH35 The indexable insert with a cutting width of 1 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0100.P0 AN25 The indexable insert with a cutting width of 1 mm is suitable for grooving and turning of outer contours with up to 2 mm depth. |
|
Paul Horn RS274.0102.01 TH35 The indexable insert with part profile is suitable for threading metric threads with a pitch of 0.25 mm. |
|
Paul Horn RS274.0102.01.E TH35 The indexable insert with part profile is suitable for threading metric threads with a pitch of 0.25 mm. |
|
Paul Horn RS274.0120.03.10 TH35 The indexable insert with a cutting width of 1.2 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0120.03.10.E TH35 The indexable insert with a cutting width of 1.2 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0120.03.20.E TH35 The indexable insert with a cutting width of 1.2 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0120.03.M0 TH35 The indexable insert with a cutting width of 1.2 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0120.03.M0.E TH35 The indexable insert with a cutting width of 1.2 mm is suitable for parting and grooving of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0147.04.SF AC25 Indexable insert |
|
Paul Horn RS274.0150.04.10 TH35 The indexable insert with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn RS274.0150.04.10.E TH35 The indexable insert with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn RS274.0150.04.20 The indexable insert TH35 with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn RS274.0150.04.20.E TH35 The indexable insert with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn RS274.0150.04.M0 The indexable insert TH35 with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn RS274.0150.04.M0.E TH35 The indexable insert with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn RS274.0150.06.10 TH35 The indexable insert with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn RS274.0150.06.10.E TH35 The indexable insert with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn RS274.0150.06.20 The indexable insert TH35 with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn RS274.0150.06.20.E TH35 The indexable insert with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn RS274.0150.06.M0 The indexable insert TH35 with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn RS274.0150.06.M0.E TH35 The indexable insert with a cutting width of 1.5 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn RS274.0150.P0 TH35 The indexable insert with a cutting width of 1.5 mm is suitable for grooving and turning of outer contours with up to 2:25 mm depth. |
|
Paul Horn RS274.0150.P0.E TH35 The indexable insert with a cutting width of 1.5 mm is suitable for grooving and turning of outer contours with up to 2:25 mm depth. |
|
Paul Horn RS274.0160.03.SF AC25 Indexable insert |
|
Paul Horn RS274.0160.03.SF MG12 Indexable insert |
|
Paul Horn RS274.0200.04.10 TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn RS274.0200.04.10.E TH35 The indexable insert with a cutting width of 2 mm is suitable for longitudinal turning of outer contours with up to 4 mm depth. |
|
Paul Horn RS274.0200.04.20 TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn RS274.0200.04.20.E TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn RS274.0200.04.M0 TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn RS274.0200.04.M0.E TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 4 mm depth. |
|
Paul Horn RS274.0200.06.10 TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn RS274.0200.06.10.E TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn RS274.0200.06.20 TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn RS274.0200.06.20.E TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn RS274.0200.06.M0 TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn RS274.0200.06.M0.E TH35 The indexable insert with a cutting width of 2 mm is suitable for parting and grooving of outer contours with up to 6 mm depth. |
|
Paul Horn RS274.0200.P0 TH35 The indexable insert with a cutting width of 2 mm is suitable for grooving and turning of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0200.P0.E TH35 The indexable insert with a cutting width of 2 mm is suitable for longitudinal turning of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0203.01 TH35 The indexable insert with part profile is suitable for threading metric threads with a pitch of 0.35mm. |
|
Paul Horn RS274.0203.01.E TH35 The indexable insert with part profile is suitable for threading metric threads with a pitch of 0.35mm. |
|
Paul Horn RS274.0204.01 TH35 The indexable insert with part profile is suitable for threading metric threads with a pitch of 0.4 mm. |
|
Paul Horn RS274.0204.01.E TH35 The indexable insert with part profile is suitable for threading metric threads with a pitch of 0.4 mm. |
|
Paul Horn RS274.0205.01.10 TH35 The indexable insert with a cutting width of 0.5 mm is suitable for grooving and turning of outer contours with up to 1.5 mm deep. |
|
Paul Horn RS274.0205.01.10.E TH35 The indexable insert with a cutting width of 0.5 mm is suitable for grooving and turning of outer contours with up to 1.5 mm deep. |
|
Paul Horn RS274.0247.04.SF AC25 Indexable insert |
|
Paul Horn RS274.0250.P0 TH35 The indexable insert with a cutting width of 2.5 mm is suitable for grooving and turning of outer contours with up to 3.75 mm depth. |
|
Paul Horn RS274.0250.P0.E TH35 The indexable insert with a cutting width of 2.5 mm is suitable for longitudinal turning of outer contours with up to 3.75 mm depth. |
|
Paul Horn RS274.0255.04.20 TH35 The indexable insert with a cutting width of 0.2 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn RS274.0255.04.20.E TH35 The indexable insert RS274.0255.04.20 TH35 with a cutting width of 0.2 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn RS274.0255.24.20 TH35 The indexable insert with a cutting width of 0.2 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn RS274.0300.P0 TH35 The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of outer contours with up to 4.5 mm deep. |
|
Paul Horn RS274.0300.P0.E TH35 The indexable insert with a cutting width of 3 mm is suitable for longitudinal turning of outer contours with up to 4.5 mm deep. |
|
Paul Horn RS274.0305.02 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.5 mm. |
|
Paul Horn RS274.0305.02.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.5 mm. |
|
Paul Horn RS274.0305.03 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.5 mm. |
|
Paul Horn RS274.0305.03.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.5 mm. |
|
Paul Horn RS274.0306.02 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.6 mm. |
|
Paul Horn RS274.0306.02.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.6 mm. |
|
Paul Horn RS274.0306.03 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.6 mm. |
|
Paul Horn RS274.0306.03.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.6 mm. |
|
Paul Horn RS274.0307.02 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.7 mm. |
|
Paul Horn RS274.0307.02.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.7 mm. |
|
Paul Horn RS274.0307.03 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.7 mm. |
|
Paul Horn RS274.0307.03.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.7 mm. |
|
Paul Horn RS274.0407.02 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.75 mm. |
|
Paul Horn RS274.0407.02.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.75 mm. |
|
Paul Horn RS274.0407.03 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.75 mm. |
|
Paul Horn RS274.0407.03.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.75 mm. |
|
Paul Horn RS274.0408.02 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.8 mm. |
|
Paul Horn RS274.0408.02.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.8 mm. |
|
Paul Horn RS274.0408.03 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.8 mm. |
|
Paul Horn RS274.0408.03.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 0.8 mm. |
|
Paul Horn RS274.0460.04.10 TH35 The indexable insert with a cutting width of 0.4 mm is suitable for reverse rotation of outer contours. |
|
Paul Horn RS274.0460.04.10.E TH35 The indexable insert with a cutting width of 0.4 mm is suitable for reverse rotation of outer contours. |
|
Paul Horn RS274.0460.04.M0 K10 Indexable insert |
|
Paul Horn RS274.0460.04.M0.E K10 Indexable insert |
|
Paul Horn RS274.0510.03.10 TH35 The indexable insert RS274.0510.03.10 TH35 with a cutting width of 1 mm is suitable for grooving and turning of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0510.03.10.E TH35 The indexable insert RS274.0510.03.10.E TH35 with a cutting width of 1 mm is suitable for grooving and turning of outer contours with up to 3 mm in depth. |
|
Paul Horn RS274.0535.06.20 TH35 The indexable insert with a cutting width of 0.5 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn RS274.0535.06.20.E TH35 The indexable insert with a cutting width of 0.5 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn RS274.0547.04.SF AC25 Indexable insert |
|
Paul Horn RS274.0555.06.20 TH35 The indexable insert with a cutting width of 0.5 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn RS274.0555.06.20.E TH35 The indexable insert with a cutting width of 0.5 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn RS274.0555.26.20 TH35 The indexable insert with a cutting width of 0.5 mm is suitable for longitudinal turning of outer contours. |
|
Paul Horn RS274.0560.06.11 TH35 The indexable insert with a cutting width of 0.5 mm is suitable for reverse rotation of outer contours. |
|
Paul Horn RS274.0560.06.11.E TH35 The indexable insert with a cutting width of 0.5 mm is suitable for reverse rotation of outer contours. |
|
Paul Horn RS274.0610.02 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1 mm. |
|
Paul Horn RS274.0610.02.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1 mm. |
|
Paul Horn RS274.0610.03 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1 mm. |
|
Paul Horn RS274.0610.03.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1 mm. |
|
Paul Horn RS274.0712.02 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.25mm. |
|
Paul Horn RS274.0712.02.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.25mm. |
|
Paul Horn RS274.0712.03 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.25mm. |
|
Paul Horn RS274.0915.02 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.5 mm. |
|
Paul Horn RS274.0915.02.E TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.5 mm. |
|
Paul Horn RS274.0915.03 TH35 The indexable insert full profile is suitable for threading metric threads with a pitch of 1.5 mm. |
|
Paul Horn RS274.1020.04.10 TH35 The indexable insert RS274.1020.04.10 TH35 with a cutting width of 2 mm is suitable for grooving and turning of outer contours with up to 4 mm depth. |
|
Paul Horn RS274.1020.04.10.E TH35 The indexable insert RS274.1020.04.10.E TH35 with a cutting width of 2 mm is suitable for grooving and turning of outer contours with up to 4 mm depth. |
|
Paul Horn RS274.1508.03.10 TH35 The indexable insert with a cutting width of 0.80 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn RS274.1508.03.10.E TH35 The indexable insert with a cutting width of 0.80 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn RS274.1508.03.10L TH35 The indexable insert with a cutting width of 0.80 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn RS274.1508.03.1L.E TH35 The indexable insert with a cutting width of 0.80 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn RS274.1508.03.M0 TH35 The indexable insert with a cutting width of 0.80 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn RS274.1508.03.M0.E TH35 The indexable insert with a cutting width of 0.80 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn RS274.1508.03.M0L TH35 The indexable insert with a cutting width of 0.80 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn RS274.1508.03.ML.E TH35 The indexable insert with a cutting width of 0.80 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn RS274.1510.03.10 TH35 The indexable insert with a cutting width of 1.00 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn RS274.1510.03.10.E TH35 The indexable insert with a cutting width of 1.00 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn RS274.1510.03.10L TH35 The indexable insert with a cutting width of 1.00 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn RS274.1510.03.1L.E TH35 The indexable insert with a cutting width of 1.00 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn RS274.1510.03.M0 TH35 The indexable insert with a cutting width of 1.00 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn RS274.1510.03.M0.E TH35 The indexable insert with a cutting width of 1.00 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn RS274.1510.03.M0L TH35 The indexable insert with a cutting width of 1.00 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn RS274.1510.03.ML.E TH35 The indexable insert with a cutting width of 1.00 mm is suitable for tapping up to 3.00mm deep. |
|
Paul Horn RS274.1510.05.M0L TH35 The indexable insert with a cutting width of 1 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn RS274.1515.04.10 TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn RS274.1515.04.10.E TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn RS274.1515.04.10L TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn RS274.1515.04.1L.E TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn RS274.1515.04.20 TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn RS274.1515.04.20.E TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn RS274.1515.04.20L TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn RS274.1515.04.2L.E TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn RS274.1515.04.M0 TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn RS274.1515.04.M0.E TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn RS274.1515.04.M0L TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn RS274.1515.04.ML.E TH35 The indexable insert with a cutting width of 1.50 mm is suitable for tapping up to 4:00 mm depth. |
|
Paul Horn RS274.1515.06.M0L TH35 The indexable insert with a cutting width of 1.5 mm is suitable for tapping up to 6 mm depth. |
|
Paul Horn RS274.1520.06.10 TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn RS274.1520.06.10.E TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn RS274.1520.06.10L TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn RS274.1520.06.1L.E TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn RS274.1520.06.20 TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn RS274.1520.06.20.E TH35 The indexable insert with a cutting width of 2.0 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn RS274.1520.06.20L TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn RS274.1520.06.2L.E TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn RS274.1520.06.M0 TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn RS274.1520.06.M0.E TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn RS274.1520.06.M0L TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn RS274.1520.06.ML.E TH35 The indexable insert with a cutting width of 2.00 mm is suitable for tapping up to 6:00 mm depth. |
|
Paul Horn RS274.2047.03.SF AC25 Indexable insert |
|
Paul Horn RS274.2047.03.SF MG12 Indexable insert |
|
Paul Horn RS274.2508.04.SF AC25 Indexable insert |
|
Paul Horn RS274.2508.04.SF MG12 Indexable insert |
|
Paul Horn RS274.2509.04.SF AC25 Indexable insert |
|
Paul Horn RS274.2510.04.SF AC25 Indexable insert |
|
Paul Horn RS274.2510.06.SF AC25 Indexable insert |
|
Paul Horn RS274.2512.06.SF AC25 Indexable insert |
|
Paul Horn RS274.2515.06.SF AC25 Indexable insert |
|
Paul Horn RS274.4508.04.SF AC25 Indexable insert |
|
Paul Horn RS274.4509.04.SF AC25 Indexable insert |
|
Paul Horn RS274.4509.04.SF MG12 Indexable insert |
|
Paul Horn RS274.4510.06.SF AC25 Indexable insert |
|
Paul Horn RS274.4512.06.SF AC25 Indexable insert |
|
Paul Horn RS274.6015.02.SF AC25 Indexable insert |
|
Paul Horn RS274.7010.02.SF AC25 Indexable insert |
|
Paul Horn RS275.0110.00 AS45 The indexable insert with a cutting width of 1.2 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn RS275.0110.40 TA45 The indexable insert with a cutting width of 1.2 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn RS275.0130.00 AS45 The indexable insert with a cutting width of 1.4 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn RS275.0130.40 TA45 The indexable insert with a cutting width of 1.4 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn RS275.0160.00 AS45 The indexable insert with a cutting width of 1.7 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn RS275.0160.40 TA45 The indexable insert with a cutting width of 1.7 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn RS275.0185.00 AS45 The indexable insert with a cutting width of 1.95 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn RS275.0185.40 TA45 The indexable insert with a cutting width of 1.95 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn RS275.0215.00 AS45 The indexable insert with a cutting width of 2.25 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn RS275.0215.40 TA45 The indexable insert with a cutting width of 2.25 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn RS275.0265.00 AS45 The indexable insert with a cutting width of 2.75 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn RS275.0265.40 TA45 The indexable insert with a cutting width of 2.75 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn RS275.0315.00 AS45 The indexable insert with a cutting width of 3.25 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn RS275.0315.40 TA45 The indexable insert with a cutting width of 3.25 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm. |
|
Paul Horn RS275.1105.41 AS45 The indexable insert with a cutting width of 1.2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 0.5 mm deep. |
|
Paul Horn RS275.1308.41 AS45 The indexable insert with a cutting width of 1.4 mm is suitable for Nutzirkularfräsen of inner and outer contours of up to 0.85 mm depth. |
|
Paul Horn RS275.1535.01 TF45 The indexable insert RS275.1535.01 TA45 with a cutting diameter of 31.00 mm is suitable for Nutzirkularfräsen of inner and outer contours with a slope 1.50 mm. |
|
Paul Horn RS275.1610.51 AS45 The indexable insert RS275.1610.41 AS45 with a cutting width of 1.7 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 1 mm depth. |
|
Paul Horn RS275.1812.41 AS45 The indexable insert with a cutting width of 1.95 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 1.25mm deep. |
|
Paul Horn RS275.2115.41 AS45 The indexable insert with a cutting width of 2.25 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 1.5 mm deep. |
|
Paul Horn RS275.2617.41 AS45 The indexable insert with a cutting width of 2.75 mm is suitable for Nutzirkularfräsen of inner and outer contours of up to 1.75 mm depth. |
|
Paul Horn RS275.3118.41 AS45 The indexable insert with a cutting width of 3.25 mm is suitable for Nutzirkularfräsen of inner and outer contours of up to 1.75 mm depth. |
|
Paul Horn RS275.AT41.HM Balancing ring, plate dummy to fill empty plate seats (weight compensation) for Mehrkantfrässystem M275 |
|
Paul Horn RS275.MK13.M0 AS45 Indexable insert |
|
Paul Horn RS275.MK13.M0 TI25 The indexable insert with a cutting width of 4 mm is suitable for multi-sided machining of inner and outer contours. |
|
Paul Horn RS275.PL40.62 TA45 The indexable insert TA45 is suitable for milling of internal and external contours with up to 3.7 mm deep. |
|
Paul Horn RS275.PL43.52 AS45 The indexable insert AS45 is suitable for milling of internal and external contours with up to 4 mm depth. |
|
Paul Horn RS279.3972.325.1 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.325.2 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.325.3 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.325.4 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.325.5 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.325.6 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.325.7 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.325.8 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.350.1L AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.350.1R AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.350.2L AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.350.2R AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.350.3 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.350.4 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.350.5 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.350.6 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.350.7 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.350.8 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.375.1L AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.375.1R AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.375.2L AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.375.3L AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.375.3R AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.375.4R AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.375.5 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.375.6 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.375.7 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.375.8 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.400.1L AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.400.1R AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.400.2L AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.400.2R AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.400.3L AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.400.3R AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.400.4L AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.400.4R AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.400.5L AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.400.5R AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.400.6L AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.400.6R AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.400.7 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS279.3972.400.8 AS45 The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute |
|
Paul Horn RS310.3017.00 AS45 The indexable insert with a cutting width of 3 mm is suitable for separating milling up to 50 mm depth. |
|
Paul Horn RS310.3118.00 AS45 The indexable insert with a cutting width of 3,175 mm is suitable for separating milling up to 50 mm depth. |
|
Paul Horn RS310.4023.00 AS45 The indexable insert with a cutting width of 4 mm is suitable for separating milling up to 50 mm depth. |
|
Paul Horn RS310.4023.00 TF45 The indexable insert with a cutting width of 4 mm is suitable for separating milling up to 50 mm depth. |
|
Paul Horn RS310.4023.00 TN35 The indexable insert with a cutting width of 4 mm is suitable for separating milling up to 50 mm depth. |
|
Paul Horn RS310.5028.00 AS45 The indexable insert with a cutting width of 5 mm is suitable for separating milling up to 50 mm depth. |
|
Paul Horn RS310.5028.00 TF45 The indexable insert with a cutting width of 5 mm is suitable for separating milling up to 50 mm depth. |
|
Paul Horn RS310.5028.00 TN35 Indexable insert for separating milling with a cutting width of 2.8 mm, corner radius 0.2 mm and a groove width of 5 mm, to a suitable milling body type M310, execution law. |
|
Paul Horn RS312.0520.C2 TF46 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn RS312.0520.C2 TI25 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn RS312.0520.F2 TF46 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn RS312.0520.F2 TI25 The indexable insert with a cutting width of 2 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn RS312.0525.C2 TF46 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn RS312.0525.C2 TI25 Indexable insert to butzenarmen parting with a cutting width of 2.5 mm and a maximum insertion depth of 5 mm, with geometry C and Abstechschräge 5 °, execution law. |
|
Paul Horn RS312.0525.F2 TF46 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn RS312.0525.F2 TI25 The indexable insert with a cutting width of 2.5 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn RS312.0530.C2 TF46 The indexable insert with a cutting width of 3 mm is suitable for tapping up to 5 mm depth. |
|
Paul Horn RS312.0530.C2 TI25 Indexable insert to butzenarmen parting with a cutting width of 3 mm and a maximum insertion depth of 5 mm, with geometry C and Abstechschräge 5 °, execution law. |
|
Paul Horn RS316.0150.FY1 TI25 The indexable insert with a cutting width of 1.5 mm is suitable for penetration of outer contours with up to 8 mm depth. |
|
Paul Horn RS316.0200.52 Indexable insert for grooving and turning at a cutting width of 2 mm, corner radius 0.2 mm and maximum piercing depth of 8 mm, suitable clamp holder H316, execution law. |
|
Paul Horn RS316.0200.EN2 AS6G The indexable insert with a cutting width of 2 mm is suitable for penetration of outer contours with up to 8 mm depth. |
|
Paul Horn RS316.0200.FY2 TI25 The indexable insert with a cutting width of 2 mm is suitable for penetration of outer contours with up to 8 mm depth. |
|
Paul Horn RS316.0250.52 Indexable insert for grooving and turning at a cutting width of 2.5 mm, corner radius 0.2 mm and maximum piercing depth of 8 mm, suitable clamp holder H316, execution law. |
|
Paul Horn RS316.0250.EN2 AS6G The indexable insert with a cutting width of 2.5 mm is suitable for penetration of outer contours with up to 8 mm depth. |
|
Paul Horn RS316.0250.FY2 TI25 The indexable insert with a cutting width of 2.5 mm is suitable for penetration of outer contours with up to 8 mm depth. |
|
Paul Horn RS316.0300.52 Indexable insert for grooving and turning at a cutting width of 3 mm, corner radius 0.2 mm and maximum piercing depth of 8 mm, suitable clamp holder H316, execution law. |
|
Paul Horn RS316.0300.EN2 AS6G The indexable insert with a cutting width of 3 mm is suitable for penetration of outer contours with up to 8 mm depth. |
|
Paul Horn RS316.0300.FY2 TI25 The indexable insert with a cutting width of 3 mm is suitable for penetration of outer contours with up to 8 mm depth. |
|
Paul Horn S.DM10 Socket wrench size 9 for assembly and disassembly of the interchangeable heads system DM10 |
|
Paul Horn S.DM12 Socket wrench size 9 for assembly and disassembly of the interchangeable heads system DM12 |
|
Paul Horn S100.0200.3V2 AS45 The insert with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn S100.0200.3V2 HP65 The insert with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn S100.0200.E2 ALX3 Insert S100.0200.E2 AlX3 for grooving and parting with a cutting width of 2 mm and 0.2 mm corner radius, with geometry E, suitable for clamping holder. B. H100. |
|
Paul Horn S100.0200.E2 TC92 The insert with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn S100.0200.E2 TC93 Insert for grooving and parting with a cutting width of 2 mm and 0.2 mm corner radius, with geometry E, suitable for clamping holder. B. H100. |
|
Paul Horn S100.0200.E2 TF43 Insert for grooving and parting with a cutting width of 2 mm and 0.2 mm corner radius, with geometry E, suitable for clamping holder. B. H100. |
|
Paul Horn S100.0200.E2 TF45 The insert with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn S100.0200.E2 TF46 Insert for grooving and parting with a cutting width of 2 mm and 0.2 mm corner radius, with geometry E, suitable for clamping holder. B. H100. |
|
Paul Horn S100.0200.E2 TI22 The insert S100.0200.E2 Ti22 with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn S100.0200.EN2 ALX3 The insert S100.0200.EN2 AlX3 with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn S100.0200.EN2 AS6G The insert with a cutting width of 2 mm is suitable for parting and grooving. |
|
Paul Horn S100.0200.F2 TC92 The insert with a cutting width of 2 mm is suitable for parting and grooving. |
