Paul Horn L240.1010.01
Toolholder with shaft 10:00 mm width x height mm 10:00 for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range 0,5 - 1,7 mm, Mod
Paul Horn L240.1010.02
Toolholder with shaft 10:00 mm width x height mm 10:00 for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 1.7 to 2.7 m
Paul Horn L240.1212.01
Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range 0,5 - 1,7 mm, M
Paul Horn L240.1212.02
Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 1.7 to 2.7
Paul Horn L240.1212.03
Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 2.7 to 3.7
Paul Horn L240.1212.04
Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 3.7 to 5.3
Paul Horn L240.1616.01
Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range 0,5 - 1,7 mm, Mod
Paul Horn L240.1616.02
Tool holders with shank 16.00 mm wide x 16.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4.00 mm and an area of ​​tension from 1.7
Paul Horn L240.1616.03
Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 2.7 to 3.7 m
Paul Horn L240.1616.04
Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 3.7 to 5.3 m
Paul Horn L240.2020.01
Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range 0,5 - 1,7 mm, M
Paul Horn L240.2020.02
Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 1.7 to 2.7
Paul Horn L240.2020.03
Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 2.7 to 3.7
Paul Horn L240.2020.04
Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range from 3.7 to 5.3
Paul Horn L245.0020.02
Toolholder with shaft diameter 20 mm for corner undercutting interior with the smallest bore diameter 20 mm for the insertion of inserts Type 217 with a clamping range from 1.7 to 2.7 mm, Model Links.
Paul Horn L245.0020.03
Toolholder with shaft diameter 20 mm for corner undercutting interior with the smallest bore diameter 20 mm for the insertion of inserts Type 217 with a clamping range from 2.7 to 3.7 mm, Model Links.
Paul Horn L245.0032.02
Toolholder with shaft diameter 32 mm for corner undercutting interior with the smallest bore diameter 31 mm for the insertion of inserts Type 217 with a clamping range from 1.7 to 2.7 mm, Model Links.
Paul Horn L245.0032.03
Toolholder with shaft diameter 32 mm for corner undercutting interior with the smallest bore diameter 31 mm for the insertion of inserts Type 217 with a clamping range from 2.7 to 3.7 mm, Model Links.
Paul Horn L245.0032.04
Toolholder with shaft diameter 32 mm for corner undercutting interior with the smallest bore diameter 31 mm for the insertion of inserts Type 217 with a clamping range from 3.7 to 5.3 mm, Model Links.
Paul Horn L248.1212.01
Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 217 with a maximum penetration depth 4:00 mm and of clamping range 0,5 - 1,7 mm, M
Paul Horn L250.0025.01
Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and a by clam
Paul Horn L250.0025.02
Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L250.0025.03
Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L250.0025.04
Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L250.0032.01
Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and a by clam
Paul Horn L250.0032.02
Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L250.0032.03
Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L250.0032.04
Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L253.0025.01
Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and a by clam
Paul Horn L253.0025.02
Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L253.0025.03
Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L253.0025.04
Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L253.0032.01
Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and a by clam
Paul Horn L253.0032.02
Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L253.0032.03
Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L253.0032.04
Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L254.0025.02
Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L254.0032.01
Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and a by clam
Paul Horn L254.0032.02
Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L254.0032.03
Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L254.0032.04
Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L255.0025.01
Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and a by clam
Paul Horn L255.0025.02
Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L255.0025.03
Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25 mm for the insertion of inserts Type 217 with a maximum penetration depth 4.70 mm and an ar
Paul Horn L255.0025.04
Toolholder with shaft diameter 25.00 mm for internal grooving and turning with the smallest bore diameter 25 mm for the insertion of inserts Type 217 with a maximum penetration depth 4.70 mm and an ar
Paul Horn L255.0032.01
Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and a by clam
Paul Horn L255.0032.02
Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L255.0032.03
Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L255.0032.04
Toolholder with shaft diameter 32.00 mm for internal grooving and turning with the smallest bore diameter 32.00 mm for receiving inserts Type 217 with a maximum penetration depth 4.70 mm and an area o
Paul Horn L264.0150.P0 TI25
Indexable insert with a cutting width of 1.5 mm, Parisian cut and maximum cutting depth of 16 mm is suitable for grooving and turning of outer contours.
Paul Horn L264.0150.P0 TN35
Indexable insert with a cutting width of 1.5 mm, Parisian cut and maximum cutting depth of 16 mm is suitable for grooving and turning of outer contours.
Paul Horn L264.0200.P0 MG12
The indexable insert with a cutting width of 2 mm is suitable for grooving and turning of outer contours with up to 16 mm depth.
Paul Horn L264.0200.P0 TI25
Indexable insert with a cutting width of 2 mm, Parisian cut and maximum cutting depth of 16 mm is suitable for grooving and turning of outer contours.
Paul Horn L264.0200.P0 TN35
Indexable insert with a cutting width of 2 mm, Parisian cut and maximum cutting depth of 16 mm is suitable for grooving and turning of outer contours.
Paul Horn L264.0200.P2 TN35
The indexable insert with a cutting width of 2 mm is suitable for grooving and turning of outer contours with up to 16 mm depth.
Paul Horn L264.0250.P0 TN35
The indexable insert with a cutting width of 2.5 mm is suitable for grooving and turning of outer contours with up to 16 mm depth.
Paul Horn L264.0250.P2 TN35
The indexable insert with a cutting width of 2.5 mm is suitable for grooving and turning of outer contours with up to 16 mm depth.
Paul Horn L264.0300.P0 MG12
The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of outer contours with up to 16 mm depth.
Paul Horn L264.0300.P0 TI25
Indexable insert with a cutting width of 3 mm, Parisian cut and maximum cutting depth of 16 mm is suitable for grooving and turning of outer contours.
Paul Horn L264.0300.P0 TN35
Indexable insert with a cutting width of 3 mm, Parisian cut and maximum cutting depth of 16 mm is suitable for grooving and turning of outer contours.
Paul Horn L264.0300.P2 TN35
The indexable insert with a cutting width of 3 mm is suitable for grooving and turning of outer contours with up to 16 mm depth.
Paul Horn L264.0305.02 TF45
Indexable insert with a pitch of 0.5 mm and maximum cutting depth 0.31 mm is suitable for chasing of metric external threads.
Paul Horn L264.0306.02 TF45
Indexable insert with a pitch of 0.6 mm and maximum cutting depth 0.37 mm is suitable for chasing of metric external threads.
Paul Horn L264.0307.02 TF45
Indexable insert with a pitch of 0.7 mm and maximum cutting depth 0.43 mm is suitable for chasing of metric external threads.
Paul Horn L264.0407.02 TF45
Indexable insert with a pitch of 0.75 mm and maximum cutting depth of 0.46mm suitable for chasing of metric external threads.
Paul Horn L264.0408.02 TF45
Indexable insert with a pitch of 0.8 mm and maximum cutting depth 0.49 mm is suitable for chasing of metric external threads.
Paul Horn L264.0610.02 TF45
Indexable insert with a pitch of 1 mm and maximum cutting depth of 0.61 mm is suitable for chasing of metric external threads.
Paul Horn L264.0712.02 TF45
Indexable insert with a pitch of 1.25mm and a maximum cutting depth of 0.77 mm is suitable for chasing of metric external threads.
Paul Horn L264.0815.10 MG12
The indexable insert with a cutting width of 1.5 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.0815.10 TN35
The indexable insert with a cutting width of 1.5 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.0815.M0 MG12
The indexable insert with a cutting width of 1.5 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.0815.M0 TN35
The indexable insert with a cutting width of 1.5 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.0820.10 MG12
The indexable insert with a cutting width of 2 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.0820.10 TN35
The indexable insert with a cutting width of 2 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.0820.M0 MG12
The indexable insert with a cutting width of 2 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.0825.10 TN35
The indexable insert with a cutting width of 2.5 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.0825.M0 MG12
The indexable insert with a cutting width of 2.5 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.0830.M0 TN35
The indexable insert with a cutting width of 3 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.0915.02 TF45
Indexable insert with a pitch of 1.5 mm and maximum cutting depth of 0.92 mm is suitable for chasing of metric external threads.
Paul Horn L264.1515.10 MG12
The indexable insert with a cutting width of 1.5 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.1515.10 TN35
The indexable insert with a cutting width of 1.5 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.1515.M0 MG12
The indexable insert with a cutting width of 1.5 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.1515.M0 TN35
The indexable insert with a cutting width of 1.5 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.1520.10 MG12
The indexable insert with a cutting width of 2 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.1520.10 TN35
The indexable insert with a cutting width of 2 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.1520.M0 MG12
The indexable insert with a cutting width of 2 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.1520.M0 TN35
The indexable insert with a cutting width of 2 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.1525.M0 MG12
The indexable insert with a cutting width of 2.5 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.1530.10 TN35
The indexable insert with a cutting width of 3 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.1530.M0 MG12
The indexable insert with a cutting width of 3 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L264.1530.M0 TN35
The indexable insert with a cutting width of 3 mm is suitable for tapping external contours with up to 16 mm depth.
Paul Horn L309.1616.01
Toolholder with shank 16 mm width x 16 mm height for producing corner undercuts for receiving inserts Type 312 with a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L309.2020.02
Toolholder with shank 20 mm width x 20 mm height for producing corner undercuts for receiving inserts Type 312 with a clamping range from 1.9 to 2.9 mm, Model Links.
Paul Horn L309.2020.03
Toolholder with shank 20 mm width x 20 mm height for producing corner undercuts for receiving inserts Type 312 with a clamping range from 2.9 to 3.9 mm, Model Links.
Paul Horn L309.2020.04
Toolholder with shank 20 mm width x 20 mm height for producing corner undercuts for receiving inserts Type 312 with a clamping range from 3.9 to 5.3 mm, Model Links.
Paul Horn L309.2525.02
Toolholder with shank 25 mm width x 25 mm height for producing corner undercuts for receiving inserts Type 312 with a clamping range from 1.9 to 2.9 mm, Model Links.
Paul Horn L309.2525.03
Toolholder with shank 25 mm width x 25 mm height for producing corner undercuts for receiving inserts Type 312 with a clamping range from 2.9 to 3.9 mm, Model Links.
Paul Horn L309.2525.04
Toolholder with shank 25 mm width x 25 mm height for producing corner undercuts for receiving inserts Type 312 with a clamping range from 3.9 to 5.3 mm, Model Links.
Paul Horn L309.3232.02
Toolholder with shank 32 mm width x 32 mm height for producing corner undercuts for receiving inserts Type 312 with a clamping range from 1.9 to 2.9 mm, Model Links.
Paul Horn L309.3232.03
Toolholder with shank 32 mm width x 32 mm height for producing corner undercuts for receiving inserts Type 312 with a clamping range from 2.9 to 3.9 mm, Model Links.
Paul Horn L309.3232.04
Toolholder with shank 32 mm width x 32 mm height for producing corner undercuts for receiving inserts Type 312 with a clamping range from 3.9 to 5.3 mm, Model Links.
Paul Horn L312.0510.00 TF45
The indexable insert with a cutting width of 1 mm is suitable for tapping up to 6 mm depth.
Paul Horn L312.0512.00 TF45
The indexable insert with a cutting width of 1.2 mm is suitable for tapping up to 8 mm depth.
Paul Horn L312.0512.M0 K10
The indexable insert with a cutting width of 1.2 mm is suitable for tapping up to 8 mm depth.
Paul Horn L312.0512.M0 TF45
Indexable insert with a cutting width of 1.2 mm and maximum cutting depth of 8 mm is suitable by Abstechschräge of 5 ° to butzenarmen parting.
Paul Horn L312.0512.V1 TF45
The indexable insert with a cutting width of 1.2 mm is suitable for tapping up to 8 mm depth.
Paul Horn L312.0515.00 TF45
The indexable insert with a cutting width of 1.5 mm is suitable for tapping up to 8 mm depth.
Paul Horn L312.0515.M0 TF45
The indexable insert with a cutting width of 1.5 mm is suitable for tapping up to 8 mm depth.
Paul Horn L312.0515.V1 TF45
The indexable insert with a cutting width of 1.5 mm is suitable for tapping up to 8 mm depth.
Paul Horn L312.0518.00 P20
The indexable insert with a cutting width of 1.99 mm is suitable for tapping up to 5 mm depth.
Paul Horn L312.0518.00 TN32
The indexable insert with a cutting width of 1.99 mm is suitable for tapping up to 5 mm depth.
Paul Horn L312.0518.00 TN35
Indexable insert with a cutting width of 1.99 mm and maximum cutting depth of 5 mm is suitable by Abstechschräge of 5 ° to butzenarmen parting.
Paul Horn L312.0520.V2 TH35
The indexable insert with a cutting width of 2 mm is suitable for tapping up to 8 mm depth.
Paul Horn L312.0521.00 P20
The indexable insert with a cutting width of 2.29 mm is suitable for tapping up to 5 mm depth.
Paul Horn L312.0521.00 TN32
Indexable insert with a cutting width of 2.29 mm and maximum cutting depth of 5 mm is suitable by Abstechschräge of 5 ° to butzenarmen parting.
Paul Horn L312.0521.00 TN35
Indexable insert with a cutting width of 2.29 mm and maximum cutting depth of 5 mm is suitable by Abstechschräge of 5 ° to butzenarmen parting.
Paul Horn L312.0522.00 TI25
The indexable insert with a cutting width of 2.29 mm is suitable for tapping up to 5 mm depth.
Paul Horn L312.0522.00 TN35
The indexable insert with a cutting width of 2.29 mm is suitable for tapping up to 5 mm depth.
Paul Horn L312.0614.00 TF45
The indexable insert with a cutting width of 1.44 mm is suitable for tapping up to 5 mm depth.
Paul Horn L312.0614.00 TI25
Indexable insert with a cutting width of 1.44 mm and maximum cutting depth of 5 mm is suitable by Abstechschräge of 6 ° to butzenarmen parting.
Paul Horn L312.0614.00 TN35
Indexable insert with a cutting width of 1.44 mm and maximum cutting depth of 5 mm is suitable by Abstechschräge of 6 ° to butzenarmen parting.
Paul Horn L312.0805.00 TF45
The indexable insert with a cutting width of 0.5 mm is suitable for tapping up to 1 mm depth.
Paul Horn L312.0808.00 TF45
The indexable insert with a cutting width of 0.8 mm is suitable for tapping up to 1.5 mm deep.
Paul Horn L312.1080.27 TN35
Indexable insert for producing thread undercuts to DIN 76 (short version) to match pitch 0.8 mm at maximum penetration depth of 0.65 mm.
Paul Horn L312.1125.27 TN35
Indexable insert for producing thread undercuts to DIN 76 (short version) to match pitch 1.25mm at maximum penetration depth of 1 mm.
Paul Horn L312.1150.37 TN35
Indexable insert for producing thread undercuts to DIN 76 (short version) to match pitch 1.5 mm at maximum penetration depth of 15.1 mm.
Paul Horn L312.1200.53 P20
The indexable insert is suitable for grooving of the inner and outer contours with up to 1.5 mm depth of thread with a pitch of 2 mm.
Paul Horn L312.1210.00 TF45
The indexable insert with a cutting width of 1 mm is suitable for tapping up to 8 mm depth.
Paul Horn L312.1210.00 TN35
The indexable insert with a cutting width of 1 mm is suitable for tapping up to 8 mm depth.
Paul Horn L312.1812.M0 K10
Indexable insert uncoated
Paul Horn L312.1812.V1 TF45
Indexable insert TiAlN coated
Paul Horn L312.2015.02 TN35
The indexable insert with a cutting width of 1.5 mm is suitable for grooving of the inner and outer contours with up to 2 mm depth.
Paul Horn L312.3020.02 TN35
The indexable insert with a cutting width of 2 mm is suitable for grooving of the inner and outer contours with up to 3 mm in depth.
Paul Horn L312.3030.02 TN35
The indexable insert with a cutting width of 3 mm is suitable for grooving of the inner and outer contours with up to 3 mm in depth.
Paul Horn L312.3031.33 P20
The indexable insert with a cutting width of 3.29 mm is suitable for grooving and turning of internal and external contours with up to 3.5 mm deep.
Paul Horn L312.3031.33 TC92
Indexable insert with `Paris Schliff\' for grooving and turning with 3:29 mm Width (corner radius 0 mm) and a maximum of 3.5 mm deep.
Paul Horn L312.3031.33 TN32
Indexable insert with `Paris Schliff\' for grooving and turning with 3:29 mm Width (corner radius 0 mm) and a maximum of 3.5 mm deep.
Paul Horn L312.3050.17 TN35
The indexable insert is suitable for grooving of the inner and outer contours with up to 0.4 mm depth of thread with a pitch of 0.5 mm.
Paul Horn L313.0130.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.41 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0150.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0150.01 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0160.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.71 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0185.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.96 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0200.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0215.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.25 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0215.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.25 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0215.00 TI25
Insert with a cutting width of 2.25 mm (nominal size Nw = 2.15 mm) and cutting circle diameter of 21.7 is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum gr
Paul Horn L313.0250.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0265.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.76 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0300.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0315.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 3.26 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0350.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 3.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0350.00 MG12
The insert with a cutting diameter of 21.7 mm and a cutting width of 3.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0350.00 TI25
Insert with a cutting width of 3.5 mm (corner radius 0.2 mm) and cutting circle diameter of 21.7 is suitable for producing grooves on the inner and outer contours with maximum groove depth of 4.5 mm.
Paul Horn L313.0400.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 4 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0415.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 4.26 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0500.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0515.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 5.26 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L313.0600.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 6 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn L314.0054.00 AS45
Indexable insert with a cutting width of 5.4 mm (corner radius 0.2 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.0054.00 TI25
Indexable insert with a cutting width of 5.4 mm (corner radius 0.2 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.0054.00 TN35
Indexable insert with a cutting width of 5.4 mm (corner radius 0.2 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.0130.00 AS45
Indexable insert with a cutting width of 1.41 mm (nominal size Nw = 1.3 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0130.00 TN35
Indexable insert with a cutting width of 1.41 mm (nominal size Nw = 1.3 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0160.00 AS45
Indexable insert with a cutting width of 1.71 mm (nominal size Nw = 1.6 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0160.00 TN35
Indexable insert with a cutting width of 1.71 mm (nominal size Nw = 1.6 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0185.00 AS45
Indexable insert with a cutting width of 1.96 mm (nominal size Nw = 1.85 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0185.00 TN35
Indexable insert with a cutting width of 1.96 mm (nominal size Nw = 1.85 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0215.00 AS45
Indexable insert with a cutting width of 26.2 mm (nominal size Nw = 2.15 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0215.00 TN35
Indexable insert with a cutting width of 26.2 mm (nominal size Nw = 2.15 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0265.00 AS45
Indexable insert with a cutting width of 2.76 mm (nominal size Nw = 2.65 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0265.00 TN35
Indexable insert with a cutting width of 2.76 mm (nominal size Nw = 2.65 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0315.00 AS45
Indexable insert with a cutting width of 26.3 mm (nominal size Nw = 3.15 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0315.00 TN35
Indexable insert with a cutting width of 26.3 mm (nominal size Nw = 3.15 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0315.40 TN35
Indexable insert with a cutting width of 26.3 mm (nominal size Nw = 3.15 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0320.20 AS45
Indexable insert with a cutting width of 6 mm (nominal size Nw = 0 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 63.5 mm.
Paul Horn L314.0415.00 AS45
Indexable insert with a cutting width of 26.4 mm (nominal size Nw = 15.4 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0415.00 TN35
Indexable insert with a cutting width of 26.4 mm (nominal size Nw = 15.4 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0430.20 AS45
Indexable insert with a cutting width of 4.3 mm (corner radius 2 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.0430.20 TI25
Indexable insert with a cutting width of 4.3 mm (corner radius 2 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.0430.25 AS45
Indexable insert with a cutting width of 4.3 mm (corner radius 2.5 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.0430.25 TI25
Indexable insert with a cutting width of 4.3 mm (corner radius 2.5 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.0515.00 AS45
Indexable insert with a cutting width of 5.26 mm (nominal size Nw = 5.15 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0515.00 TN35
Indexable insert with a cutting width of 5.26 mm (nominal size Nw = 15.5 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0515.40 TN35
Indexable insert with a cutting width of 5.26 mm (nominal size Nw = 15.5 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L314.0540.20 AS45
Indexable insert with a cutting width of 5:43 mm (corner radius 2 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.0540.20 TI25
Indexable insert with a cutting width of 5:43 mm (corner radius 2 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.0540.25 AS45
Indexable insert with a cutting width of 5:44 mm (corner radius 2.5 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.0540.25 TI25
Indexable insert with a cutting width of 5:44 mm (corner radius 2.5 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.0540.40 AS45
Indexable insert with a cutting width of EUR 5.47 mm (corner radius 4 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.0540.40 TI25
Indexable insert with a cutting width of EUR 5.47 mm (corner radius 4 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.1307.54 AS45
Indexable insert with a cutting width of 1.41 mm (nominal size Nw = 1.3 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum groo
Paul Horn L314.1308.54 AS45
Indexable insert with a cutting width of 1.41 mm (nominal size Nw = 1.3 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum groo
Paul Horn L314.1609.54 AS45
Indexable insert with a cutting width of 1.71 mm (nominal size Nw = 1.6 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum groo
Paul Horn L314.1609.54 TN35
Indexable insert with a cutting width of 1.71 mm (nominal size Nw = 1.6 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum groo
Paul Horn L314.1610.54 AS45
Indexable insert with a cutting width of 1.71 mm (nominal size Nw = 1.6 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum groo
Paul Horn L314.1610.54 TN35
Indexable insert with a cutting width of 1.71 mm (nominal size Nw = 1.6 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum groo
Paul Horn L314.1812.54 AS45
Indexable insert with a cutting width of 1.96 mm (nominal size Nw = 1.85 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum gro
Paul Horn L314.1812.54 TN35
Indexable insert with a cutting width of 1.96 mm (nominal size Nw = 1.85 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum gro
Paul Horn L314.2115.54 AS45
Indexable insert with a cutting width of 26.2 mm (nominal size Nw = 2.15 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum gro
Paul Horn L314.2115.54 TN35
Indexable insert with a cutting width of 26.2 mm (nominal size Nw = 2.15 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum gro
Paul Horn L314.2616.54 AS45
Indexable insert with a cutting width of 2.76 mm (nominal size Nw = 2.65 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum gro
Paul Horn L314.2616.54 TN35
Indexable insert with a cutting width of 2.76 mm (nominal size Nw = 2.65 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum gro
Paul Horn L314.2617.54 AS45
Indexable insert with a cutting width of 2.76 mm (nominal size Nw = 2.65 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum gro
Paul Horn L314.2617.54 TN35
Indexable insert with a cutting width of 2.76 mm (nominal size Nw = 2.65 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum gro
Paul Horn L314.3118.54 AS45
Indexable insert with a cutting width of 26.3 mm (nominal size Nw = 3.15 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum gro
Paul Horn L314.3118.54 TN35
Indexable insert with a cutting width of 26.3 mm (nominal size Nw = 3.15 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum gro
Paul Horn L314.4120.54 AS45
Indexable insert with a cutting width of 26.4 mm (nominal size Nw = 15.4 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum gro
Paul Horn L314.4125.54 AS45
Indexable insert with a cutting width of 26.4 mm (nominal size Nw = 15.4 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum gro
Paul Horn L314.5130.61 AS45
Indexable insert with a cutting width of 5.26 mm (nominal size Nw = 15.5 mm) is suitable for producing Seegerringnuten DIN 471/472 with NutauГџenkantenfase to inner and outer contours with maximum gro
Paul Horn L314.6032.00 AS45
Indexable insert with a cutting width of 3.2 mm (corner radius 0.2 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.6032.00 TI25
Indexable insert with a cutting width of 3.2 mm (corner radius 0.2 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.6032.00 TN35
Indexable insert with a cutting width of 3.2 mm (corner radius 0.2 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.8043.00 AS45
Indexable insert with a cutting width of 4.3 mm (corner radius 0.2 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.8043.00 TI25
Indexable insert with a cutting width of 4.3 mm (corner radius 0.2 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.8043.00 TN35
Indexable insert with a cutting width of 4.3 mm (corner radius 0.2 mm) is suitable for producing grooves on the inner and outer contours.
Paul Horn L314.AT30.HM
Balancing ring, plate dummy to fill empty plate seats (weight compensation) for Mehrkantfrässystem 381
Paul Horn L314.MK50.20 AS45
Indexable insert with a cutting width of 5 mm (corner radius 0.15mm) is suitable for the manufacture of outer polygons (Polygon, polygonal milling) in lathes.
Paul Horn L314.MK50.20 TI25
Indexable insert with a cutting width of 5 mm (corner radius 0.15mm) is suitable for the manufacture of outer polygons (Polygon, polygonal milling) in lathes.
Paul Horn L314.MK50.20.L TI25
Indexable insert with a cutting width of 5.4 mm (corner radius 0.6 mm) is suitable for the manufacture of outer polygons (Polygon, polygonal milling) in lathes.
Paul Horn L314.MK50.20L AS45
Indexable insert with a cutting width of 5.4 mm (corner radius 0.6 mm) is suitable for the manufacture of outer polygons (Polygon, polygonal milling) in lathes.
Paul Horn L314.MK50.5.20 TI25
Indexable insert with a cutting width of 5 mm (corner radius 0.15mm) is suitable for the manufacture of outer polygons (Polygon, polygonal milling) in lathes.
Paul Horn L314.MK70.M0 AS45
Indexable insert with a cutting width of 7 mm (corner radius 0.15mm) is suitable for the manufacture of outer polygons (Polygon, polygonal milling) in lathes.
Paul Horn L314.MK70.M0 TI25
Indexable insert with a cutting width of 7 mm (corner radius 0.15mm) is suitable for the manufacture of outer polygons (Polygon, polygonal milling) in lathes.
Paul Horn L314.MK70.M0 TN35
Indexable insert with a cutting width of 7 mm (corner radius 0.15mm) is suitable for the manufacture of outer polygons (Polygon, polygonal milling) in lathes.
Paul Horn L315.0050.32.00 TN32
The indexable insert with a cutting width of 0.57 mm is suitable for grooving of the inner and outer contours with up to 0.7 mm deep.
Paul Horn L315.0060.32.00 TN32
The indexable insert with a cutting width of 0.67 mm is suitable for grooving of the inner and outer contours with up to 0.8 mm deep.
Paul Horn L315.0070.32.00 TN32
The indexable insert with a cutting width of 0.77 mm is suitable for grooving of the inner and outer contours with up to 1.1 mm deep.
Paul Horn L315.0080.32.00 TN32
The indexable insert with a cutting width of 0.87 mm is suitable for grooving of the inner and outer contours with up to 1.2 mm deep.
Paul Horn L315.0090.32.00 TN32
The indexable insert with a cutting width of 0.97 mm is suitable for grooving of the inner and outer contours with up to 1.4 mm deep.
Paul Horn L315.0100.05 AS45
Indexable insert with a cutting width of 1 mm (nominal size Nw = 0 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 2.5 mm.
Paul Horn L315.0100.32.00 TN32
The indexable insert with a cutting width of 1.07 mm is suitable for grooving of the inner and outer contours with up to 1.6 mm deep.
Paul Horn L315.0110.00 AS42
Indexable insert with a cutting width of 24.1 mm (nominal size Nw = 1.1 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 2 mm.
Paul Horn L315.0110.00 AS46
Indexable insert with a cutting width of 24.1 mm (nominal size Nw = 1.1 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 2 mm.
Paul Horn L315.0110.00 TF45
Indexable insert with a cutting width of 24.1 mm (nominal size Nw = 1.1 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 2 mm.
Paul Horn L315.0110.00 TN35
The indexable insert with a cutting width of 1.24 mm is suitable for grooving of the inner and outer contours with up to 2 mm depth.
Paul Horn L315.0130.00 AS42
Indexable insert with a cutting width of 1.44 mm (nominal size Nw = 1.3 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 2 mm.
Paul Horn L315.0130.00 AS46
Indexable insert with a cutting width of 1.44 mm (nominal size Nw = 1.3 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 2 mm.
Paul Horn L315.0130.00 TF45
Indexable insert with a cutting width of 1.44 mm (nominal size Nw = 1.3 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 2 mm.
Paul Horn L315.0130.00 TN35
The indexable insert with a cutting width of 1.44 mm is suitable for grooving of the inner and outer contours with up to 2 mm depth.
Paul Horn L315.0150.07 AS45
Indexable insert with a cutting width of 1.5 mm with radius 0.75 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0160.00 AS42
Indexable insert with a cutting width of 1.74 mm (nominal size Nw = 1.6 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 3 mm.
Paul Horn L315.0160.00 AS46
Indexable insert with a cutting width of 1.74 mm (nominal size Nw = 1.6 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 3 mm.
Paul Horn L315.0160.00 TF45
Indexable insert with a cutting width of 1.74 mm (nominal size Nw = 1.6 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 3 mm.
Paul Horn L315.0160.00 TN35
The indexable insert with a cutting width of 1.74 mm is suitable for grooving of the inner and outer contours with up to 3 mm in depth.
Paul Horn L315.0160.08 AS45
Indexable insert with a cutting width of 1.6 mm with radius 0.8 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0180.09 AS45
Indexable insert with a cutting width of 1.8 mm with radius of 0.9 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0185.00 AS42
Indexable insert with a cutting width of 1.99 mm (nominal size Nw = 1.85 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 3 mm.
Paul Horn L315.0185.00 AS46
Indexable insert with a cutting width of 1.99 mm (nominal size Nw = 1.85 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 3 mm.
Paul Horn L315.0185.00 TF45
Indexable insert with a cutting width of 1.99 mm (nominal size Nw = 1.85 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 3 mm.
Paul Horn L315.0185.00 TN35
The indexable insert with a cutting width of 1.99 mm is suitable for grooving of the inner and outer contours with up to 3 mm in depth.
Paul Horn L315.0200.02 AS42
Indexable insert with a cutting width of 2 mm with corner radius 0.2 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 3 mm.
Paul Horn L315.0200.02 AS46
Indexable insert with a cutting width of 2 mm with corner radius 0.2 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 3 mm.
Paul Horn L315.0200.02 TN35
The indexable insert with a cutting width of 2 mm is good for copying inner and outer contours with up to 3 mm in depth.
Paul Horn L315.0200.04 AS42
Indexable insert with a cutting width of 2 mm with corner radius 0.4 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 3 mm.
Paul Horn L315.0200.04 AS46
Indexable insert with a cutting width of 2 mm with corner radius 0.4 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 3 mm.
Paul Horn L315.0200.04 TN35
The indexable insert with a cutting width of 2 mm is good for copying inner and outer contours with up to 3 mm in depth.
Paul Horn L315.0200.10 AS45
Indexable insert with a cutting width of 2 mm with radius 1 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0215.00 AS42
Indexable insert with a cutting width of 2.29 mm (nominal size Nw = 2.15 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 4 mm.
Paul Horn L315.0215.00 AS46
Indexable insert with a cutting width of 2.29 mm (nominal size Nw = 2.15 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 4 mm.
Paul Horn L315.0215.00 TF45
Indexable insert with a cutting width of 2.29 mm (nominal size Nw = 2.15 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 4 mm.
Paul Horn L315.0215.00 TN35
The indexable insert with a cutting width of 2.29 mm is suitable for grooving of the inner and outer contours with up to 4 mm depth.
Paul Horn L315.0220.11 AS45
Indexable insert with a cutting width of 2.2 mm with radius 1.1 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0250.12 AS45
Indexable insert with a cutting width of 2.5 mm with full radius 1.25mm suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0265.00 AS42
Indexable insert with a cutting width of 2.79 mm (nominal size Nw = 2.65 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 4 mm.
Paul Horn L315.0265.00 AS46
Indexable insert with a cutting width of 2.79 mm (nominal size Nw = 2.65 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 4 mm.
Paul Horn L315.0265.00 TF45
Indexable insert with a cutting width of 2.79 mm (nominal size Nw = 2.65 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 4 mm.
Paul Horn L315.0265.00 TN35
The indexable insert with a cutting width of 2.79 mm is suitable for grooving of the inner and outer contours with up to 4 mm depth.
Paul Horn L315.0280.14 AS45
Indexable insert with a cutting width of 2.8 mm with radius of 1.4 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0300.02 AS42
Indexable insert with a cutting width of 3 mm with corner radius 0.2 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 4 mm.
Paul Horn L315.0300.02 AS46
Indexable insert with a cutting width of 3 mm with corner radius 0.2 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 4 mm.
Paul Horn L315.0300.02 TC92
Indexable insert multi-layer coated
Paul Horn L315.0300.02 TN35
The indexable insert with a cutting width of 3 mm is suitable for grooving and copying inner and outer contours up to 4 mm depth.
Paul Horn L315.0300.04 AS42
Indexable insert with a cutting width of 3 mm with corner radius 0.4 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 4 mm.
Paul Horn L315.0300.04 AS46
Indexable insert with a cutting width of 3 mm with corner radius 0.4 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 4 mm.
Paul Horn L315.0300.04 TN35
The indexable insert with a cutting width of 3 mm is suitable for grooving and copying inner and outer contours up to 4 mm depth.
Paul Horn L315.0300.15 AS45
Indexable insert with a cutting width of 3 mm with radius 1.5 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0315.00 AS42
Indexable insert with a cutting width of 3.29 mm (nominal size Nw = 3.15 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0315.00 AS46
Indexable insert with a cutting width of 3.29 mm (nominal size Nw = 3.15 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0315.00 TF45
Indexable insert with a cutting width of 3.29 mm (nominal size Nw = 3.15 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0315.00 TN35
The indexable insert with a cutting width of 3.29 mm is suitable for grooving of the inner and outer contours up to 5 mm depth.
Paul Horn L315.0360.18 AS45
Indexable insert with a cutting width of 3.6 mm with radius of 1.8 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0400.02 AS42
Indexable insert with a cutting width of 4 mm with corner radius 0.2 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0400.02 AS45
Indexable insert TiAlN nano-composite coated
Paul Horn L315.0400.02 AS46
Indexable insert with a cutting width of 4 mm with corner radius 0.2 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0400.02 TN35
Indexable insert with a cutting width of 4 mm with corner radius 0.2 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0400.04 AS42
Indexable insert with a cutting width of 4 mm with corner radius 0.4 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0400.04 AS46
Indexable insert with a cutting width of 4 mm with corner radius 0.4 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0400.04 TN35
Indexable insert with a cutting width of 4 mm with corner radius 0.4 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0400.20 AS45
Indexable insert with a cutting width of 4 mm with radius 2 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0415.00 AL96
Indexable insert with a cutting width of 29.4 mm (nominal size Nw = 15.4 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0415.00 AS42
Indexable insert with a cutting width of 29.4 mm (nominal size Nw = 15.4 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0415.00 AS46
Indexable insert with a cutting width of 29.4 mm (nominal size Nw = 15.4 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0415.00 TF45
Indexable insert with a cutting width of 29.4 mm (nominal size Nw = 15.4 mm) is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0415.00 TN35
The indexable insert with a cutting width of 4.29 mm is suitable for grooving of the inner and outer contours up to 5 mm depth.
Paul Horn L315.0500.02 AS45
Indexable insert with a cutting width of 5 mm with corner radius 0.2 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0510.01 TN35
The indexable insert with part profile is suitable for threading metric threads with a pitch of 1 mm.
Paul Horn L315.0600.04 AS45
Indexable insert with a cutting width of 6 mm with corner radius 0.4 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0610.01 TN35
The indexable insert with part profile is suitable for threading metric threads with a pitch of 1 mm.
Paul Horn L315.0610.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 1 mm.
Paul Horn L315.0712.01 TN35
The indexable insert with part profile is suitable for threading metric threads with a pitch of 1.25mm.
Paul Horn L315.0712.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 1.25mm.
Paul Horn L315.0800.04 AS45
Indexable insert with a cutting width of 8 mm with corner radius 0.4 mm is suitable for grooving grooves on inner and outer contours with maximum groove depth of 5 mm.
Paul Horn L315.0815.01 TN35
The indexable insert with part profile is suitable for threading metric threads with a pitch of 1.5 mm.
Paul Horn L315.0915.01 TN35
The indexable insert with part profile is suitable for threading metric threads with a pitch of 1.5 mm.
Paul Horn L315.0915.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 1.5 mm.
Paul Horn L315.1015.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 1.5 mm.
Paul Horn L315.1017.01 TN35
The indexable insert with part profile is suitable for threading metric threads with a pitch of 1.75 mm.
Paul Horn L315.1017.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 1.75 mm.
Paul Horn L315.1020.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 2 mm.
Paul Horn L315.1220.01 TN35
The indexable insert with part profile is suitable for threading metric threads with a pitch of 2 mm.
Paul Horn L315.1220.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 2 mm.
Paul Horn L315.1320.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 2 mm.
Paul Horn L315.1525.01 TN35
The indexable insert with part profile is suitable for threading metric threads with a pitch of 2.5 mm.
Paul Horn L315.1525.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 2.5 mm.
Paul Horn L315.1630.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 3 mm.
Paul Horn L315.1730.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 3 mm.
Paul Horn L315.1830.01 TN35
The indexable insert with part profile is suitable for threading metric threads with a pitch of 3 mm.
Paul Horn L315.1830.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 3 mm.
Paul Horn L315.2135.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 3.5 mm.
Paul Horn L315.2240.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 4 mm.
Paul Horn L315.2440.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 4 mm.
Paul Horn L315.2750.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 5 mm.
Paul Horn L315.3050.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 5 mm.
Paul Horn L315.3060.01 TN35
The indexable insert with part profile is suitable for threading metric threads with a pitch of 3 mm.
Paul Horn L315.3560.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 6 mm.
Paul Horn L315.3660.02 TN35
The indexable insert full profile is suitable for threading metric threads with a pitch of 6 mm.
Paul Horn L315.5511.02 TH35
The indexable insert full profile is suitable for threading of Whitworth pipe threads with a pitch of 11 threads / inch.
Paul Horn L315.5514.02 TH35
The indexable insert full profile is suitable for threading of Whitworth pipe threads with a pitch of 14 transition / inch.
Paul Horn L315.5519.02 TH35
The indexable insert full profile is suitable for threading of Whitworth pipe threads with a pitch of 19 transition / inch.
Paul Horn L315.5528.02 TH35
The indexable insert full profile is suitable for threading of Whitworth pipe threads with a pitch of 28 transition / inch.
Paul Horn L330.0025.01
Basic holder as boring bar shank diameter 25.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0025.02
Basic holder as boring bar shank diameter 25.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0025.K2
Basic holder as boring bar shank diameter 25.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0025.K3
Basic holder as boring bar shank diameter 25.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0025.K4
Basic holder as boring bar shank diameter 25.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0032.01
Basic holder as boring bar shank diameter 32.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0032.02
Basic holder as boring bar shank diameter 32.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0032.03
Basic holder as boring bar shank diameter 32.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0032.04
Basic holder as boring bar shank diameter 32.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0032.K2
Basic holder as boring bar shank diameter 32.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0032.K3
Basic holder as boring bar shank diameter 32.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0032.K4
Basic holder as boring bar shank diameter 32.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0040.01
Basic holder as boring bar shank diameter 40.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0040.02
Basic holder as boring bar shank diameter 40.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0040.03
Basic holder as boring bar shank diameter 40.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0040.04
Basic holder as boring bar shank diameter 40.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0040.K2
Basic holder as boring bar shank diameter 40.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0040.K3
Basic holder as boring bar shank diameter 40.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L330.0040.K4
Basic holder as boring bar shank diameter 40.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 46.00 mm.
Paul Horn L333.0025.03
Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 43.00 mm.
Paul Horn L333.0025.05
Toolholder as boring bar shank diameter 25.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 43.00 mm.
Paul Horn L333.0032.03
Toolholder as boring bar shank diameter 32.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 43.00 mm.
Paul Horn L333.0032.05
Toolholder as boring bar shank diameter 32.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 43.00 mm.
Paul Horn L333.0040.05
Toolholder as boring bar shank diameter 40.00 mm for receiving indexable inserts Type 312, with the smallest bore diameter 45.00 mm.
Paul Horn L356.1616.0.13.IK
Toolholder with shank 16 mm width x 16 mm height for external grooving and turning for receiving inserts Type 315, Type Links.
Paul Horn L356.1616.0.15.IK
Toolholder with shank 16 mm width x 16 mm height for external grooving and turning for receiving inserts Type 315, Type Links.
Paul Horn L356.1616.03
Toolholder with shank 16 mm width x 16 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 0.5 to 3.1 mm, Model Links.
Paul Horn L356.1616.05
Toolholder with shank 16 mm width x 16 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 0.5 to 5.3 mm, Model Links.
Paul Horn L356.1616.13
Toolholder with shank 16 mm width x 16 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 0.5 to 3.1 mm, Model Links.
Paul Horn L356.1616.15
Toolholder with shank 16 mm width x 16 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 0.5 to 5.3 mm, Model Links.
Paul Horn L356.1616.16
Toolholder with shank 16 mm width x 16 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 5.3 to 6.4 mm, Model Links.
Paul Horn L356.1616.2.13.IK
Toolholder with shank 16 mm width x 16 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range of 0 mm, Model Links.
Paul Horn L356.1616.2.15.IK
Toolholder with shank 16 mm width x 16 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range of 0 mm, Model Links.
Paul Horn L356.2020.0.13.IK
Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range of 0 mm, Model Links.
Paul Horn L356.2020.0.15.IK
Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range of 0 mm, Model Links.
Paul Horn L356.2020.03
Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 0.5 to 3.1 mm, Model Links.
Paul Horn L356.2020.05
Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 0.5 to 5.3 mm, Model Links.
Paul Horn L356.2020.07
Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 6.4 to 7.3 mm, Model Links.
Paul Horn L356.2020.10
Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 7.3 to 10.3 mm, Model Links.
Paul Horn L356.2020.13
Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 0.5 to 3.1 mm, Model Links.
Paul Horn L356.2020.15
Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 0.5 to 5.3 mm, Model Links.
Paul Horn L356.2020.16
Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 5.3 to 6.4 mm, Model Links.
Paul Horn L356.2020.17
Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 5.3 to 6.4 mm, Model Links.
Paul Horn L356.2020.2.13
Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 10.3 to 13.3 mm, Model Links.
Paul Horn L356.2020.2.13.IK
Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range of 0 mm, Model Links.
Paul Horn L356.2020.2.15.IK
Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range of 0 mm, Model Links.
Paul Horn L356.2020.45.03
Toolholder with shank 20 mm width x 20 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range of 0 mm, Model Links.
Paul Horn L356.2525.0.13.IK
Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range of 0 mm, Model Links.
Paul Horn L356.2525.0.15.IK
Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range of 0 mm, Model Links.
Paul Horn L356.2525.03
Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 0.5 to 3.1 mm, Model Links.
Paul Horn L356.2525.05
Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 0.5 to 5.3 mm, Model Links.
Paul Horn L356.2525.07
Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 6.4 to 7.3 mm, Model Links.
Paul Horn L356.2525.13
Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 0.5 to 3.1 mm, Model Links.
Paul Horn L356.2525.15
Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 0.5 to 5.3 mm, Model Links.
Paul Horn L356.2525.16
Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 5.3 to 6.4 mm, Model Links.
Paul Horn L356.2525.17
Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 5.3 to 6.4 mm, Model Links.
Paul Horn L356.2525.2.13
Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 10.3 to 13.3 mm, Model Links.
Paul Horn L356.2525.2.13.IK
Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range of 0 mm, Model Links.
Paul Horn L356.2525.2.15.IK
Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range of 0 mm, Model Links.
Paul Horn L356.2525.4.03.IK
Toolholder with shank 25 mm width x 25 mm height with integrated internal coolant supply, for parting and grooving for receiving inserts Type 315, Type Links.
Paul Horn L356.2525.4.05.IK
Toolholder with shank 25 mm width x 25 mm height with integrated internal coolant supply, for parting and grooving for receiving inserts Type 315, Type Links.
Paul Horn L356.2525.45.03
Toolholder with shank 25 mm width x 25 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range of 0 mm, Model Links.
Paul Horn L356.3232.03
Toolholder with shank 32 mm width x 32 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 0.5 to 3.1 mm, Model Links.
Paul Horn L356.3232.05
Toolholder with shank 32 mm width x 32 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 0.5 to 5.3 mm, Model Links.
Paul Horn L356.3232.07
Toolholder with shank 32 mm width x 32 mm height for external grooving and turning for receiving inserts Type 315 with a clamping range from 6.4 to 7.3 mm, Model Links.
Paul Horn L357.1619.05
Quick clamp holder for installation purposes for receiving inserts Type 315, clamping range 0,5 - 5,3 mm, from bore diameter 50.00 mm, Model Links.
Paul Horn L357.2020.05
Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 315 at maximum penetration depth of 5.00 mm and a clamping range from 0.5 to 5.3 m
Paul Horn L357.2020.15
Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 315 at maximum penetration depth of 5.00 mm and a clamping range from 0.5 to 5.3 m
Paul Horn L357.2525.05
Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 315 at maximum penetration depth of 5.00 mm and a clamping range from 0.5 to 5.3 mm
Paul Horn L357.2525.15
Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 315 at maximum penetration depth of 5.00 mm and a clamping range from 0.5 to 5.3 mm
Paul Horn L360.00C3.K1
Tool holders with HORN polygonal shank ISO 26623 for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L360.00C3.K3
Tool holders with HORN polygonal shank ISO 26623 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 mm, Model Links.
Paul Horn L360.00C3.K4
Tool holders with HORN polygonal shank ISO 26623 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 3.9 to 6.3 mm, Model Links.
Paul Horn L360.00C4.K1
Tool holders with HORN polygonal shank ISO 26623 for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L360.00C4.K2
Tool holders with HORN polygonal shank ISO 26623 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 1.9 to 2.9 mm, Model Links.
Paul Horn L360.00C4.K3
Tool holders with HORN polygonal shank ISO 26623 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 mm, Model Links.
Paul Horn L360.00C4.K4
Tool holders with HORN polygonal shank ISO 26623 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 3.9 to 6.3 mm, Model Links.
Paul Horn L360.00C5.K1
Tool holders with HORN polygonal shank ISO 26623 for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L360.00C5.K2
Tool holders with HORN polygonal shank ISO 26623 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 1.9 to 2.9 mm, Model Links.
Paul Horn L360.00C5.K3
Tool holders with HORN polygonal shank ISO 26623 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 mm, Model Links.
Paul Horn L360.00C5.K4
Tool holders with HORN polygonal shank ISO 26623 for receiving inserts Type 312 at maximum penetration depth of 6.00 mm and a clamping range from 3.9 to 6.3 mm, Model Links.
Paul Horn L360.00C6.K1
Tool holders with HORN polygonal shank ISO 26623 for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L360.00C6.K2
Tool holders with HORN polygonal shank ISO 26623 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 1.9 to 2.9 mm, Model Links.
Paul Horn L360.00C6.K3
Tool holders with HORN polygonal shank ISO 26623 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 mm, Model Links.
Paul Horn L360.00C6.K4
Tool holders with HORN polygonal shank ISO 26623 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 3.9 to 6.3 mm, Model Links.
Paul Horn L360.1212.01
Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 m
Paul Horn L360.1212.01.IK
Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 m
Paul Horn L360.1212.02
Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 1.9 to 2.9 m
Paul Horn L360.1212.02.IK
Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 1.9 to 2.9 m
Paul Horn L360.1212.03
Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 m
Paul Horn L360.1212.03.IK
Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 m
Paul Horn L360.1616.01
Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 mm,
Paul Horn L360.1616.01.IK
Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 mm,
Paul Horn L360.1616.02
Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 1.9 to 2.9 mm,
Paul Horn L360.1616.02.IK
Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 1.9 to 2.9 mm,
Paul Horn L360.1616.03
Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 mm,
Paul Horn L360.1616.03.IK
Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 mm,
Paul Horn L360.1616.04
Tool holders with shank 16.00mm width x 16.00mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 3.9 to 6.3 mm,
Paul Horn L360.2020.01
Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 m
Paul Horn L360.2020.01.IK
Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 m
Paul Horn L360.2020.02
Tool holders with shank 20.00 mm wide x 20.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6.00 mm and a clamping range from 1.9 to 2.9 mm
Paul Horn L360.2020.02.IK
Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 1.9 to 2.9 m
Paul Horn L360.2020.03
Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 m
Paul Horn L360.2020.03.IK
Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 m
Paul Horn L360.2020.04
Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 3.9 to 6.3 m
Paul Horn L360.2525.01
Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 mm
Paul Horn L360.2525.01.IK
Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 mm
Paul Horn L360.2525.02
Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 1.9 to 2.9 mm
Paul Horn L360.2525.02.IK
Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 1.9 to 2.9 mm
Paul Horn L360.2525.03
Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 mm
Paul Horn L360.2525.03.IK
Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 mm
Paul Horn L360.2525.04
Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6.00 mm and a clamping range from 3.9 to 6.3 mm
Paul Horn L360.3232.01
Tool holders with shank 32.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 mm
Paul Horn L360.3232.02
Tool holders with shank 32.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 1.9 to 2.9 mm
Paul Horn L360.3232.03
Tool holders with shank 32.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 mm
Paul Horn L360.3232.04
Tool holders with shank 32.00 mm wide x 32.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 3.9 to 6.3 mm
Paul Horn L360.TS40.K1
Tool holders with HORN shaft TS ISO 26622 for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L360.TS40.K2
Tool holders with HORN shaft TS ISO 26622 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 1.9 to 2.9 mm, Model Links.
Paul Horn L360.TS40.K3
Tool holders with HORN shaft TS ISO 26622 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 mm, Model Links.
Paul Horn L360.TS40.K4
Tool holders with HORN shaft TS ISO 26622 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 3.9 to 6.3 mm, Model Links.
Paul Horn L360.TS50.K1
Tool holders with HORN shaft TS ISO 26622 for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L360.TS50.K2
Tool holders with HORN shaft TS ISO 26622 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 1.9 to 2.9 mm, Model Links.
Paul Horn L360.TS50.K3
Tool holders with HORN shaft TS ISO 26622 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 mm, Model Links.
Paul Horn L360.TS50.K4
Tool holders with HORN shaft TS ISO 26622 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 3.9 to 6.3 mm, Model Links.
Paul Horn L360.TS63.K1
Tool holders with HORN shaft TS ISO 26622 for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L360.TS63.K2
Tool holders with HORN shaft TS ISO 26622 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 1.9 to 2.9 mm, Model Links.
Paul Horn L360.TS63.K3
Tool holders with HORN shaft TS ISO 26622 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 mm, Model Links.
Paul Horn L360.TS63.K4
Tool holders with HORN shaft TS ISO 26622 for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 3.9 to 6.3 mm, Model Links.
Paul Horn L361.1212.01
Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range of 0.5-1.9 mm, Mo
Paul Horn L361.1212.02
Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 1.9 to 2.9 m
Paul Horn L361.1212.03
Tool holders with shank 12.00 mm Width x 12.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 m
Paul Horn L368.0710.08
Toolholder machines specifically for TORNOS DECO 7/10 parting for receiving inserts Type 312 at maximum penetration depth from 8.00 mm and a clamping range of 0 mm, Model Links.
Paul Horn L368.0710.11
Toolholder machines specifically for TORNOS DECO 7/10 parting for receiving inserts Type 312 at maximum penetration depth from 8.00 mm and a clamping range of 0 mm, Model Links.
Paul Horn L368.1212.08
Tool holders with shank 12.00 mm Width x 12.00 mm height for tapping for receiving inserts Type 312 at maximum penetration depth from 8.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L368.1212.08.IK
Tool holders with shank 12.00 mm Width x 12.00 mm height for tapping for receiving inserts Type 312 at maximum penetration depth from 8.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L368.1212.11
Tool holders with shank 12.00 mm Width x 12.00 mm height for tapping for receiving inserts Type 312 at maximum penetration depth from 8.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L368.1212.11.IK
Tool holders with shank 12.00 mm Width x 12.00 mm height for tapping for receiving inserts Type 312 at maximum penetration depth from 8.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L368.1616.08
Tool holders with shank 16.00mm width x 16.00mm height for tapping for receiving inserts Type 312 at maximum penetration depth from 8.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L368.1616.08.IK
Tool holders with shank 16.00mm width x 16.00mm height for tapping for receiving inserts Type 312 at maximum penetration depth from 8.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L368.1616.11
Tool holders with shank 16.00mm width x 16.00mm height for tapping for receiving inserts Type 312 at maximum penetration depth from 8.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L368.1616.11.IK
Tool holders with shank 16.00mm width x 16.00mm height for tapping for receiving inserts Type 312 at maximum penetration depth from 8.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L368.2608.08
Toolholder as Abstechschwert 8:00 mm wide x 26.00 mm height for receiving inserts Type 312 at maximum penetration depth from 8.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L368.2608.10.01
Tool holders type
Paul Horn L368.2608.11
Toolholder as Abstechschwert 8:00 mm wide x 26.00 mm height for receiving inserts Type 312 at maximum penetration depth from 8.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L368.3208.08
Toolholder as Abstechschwert 8:00 mm wide x 32.00 mm height for receiving inserts Type 312 at maximum penetration depth from 8.00 mm and a clamping range from 0.5 to 1.9 mm, Model Links.
Paul Horn L369.2020.01
Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 m
Paul Horn L369.2020.02
Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 1.9 to 2.9 m
Paul Horn L369.2020.03
Tool holders with shank 20.00 mm Width x 20.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 m
Paul Horn L369.2020.04
Tool holders with shank 20.00 mm wide x 20.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6.00 mm and a clamping range from 3.9 to 6.3 mm
Paul Horn L369.2525.01
Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a clamping range from 0.5 to 1.9 mm
Paul Horn L369.2525.02
Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 1.9 to 2.9 mm
Paul Horn L369.2525.03
Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 2.9 to 3.9 mm
Paul Horn L369.2525.04
Tool holders with shank 25.00 mm wide x 25.00 mm height for external grooving and turning for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a clamping range from 3.9 to 6.3 mm
Paul Horn L369.A022.18.01
Toolholder machines specifically for STAR SV 12/20/32, SR10 / 20/32 and SB 16 to the outer piercing and turning operations for receiving inserts Type 312 at maximum penetration depth of 4.00 mm and a
Paul Horn L369.A022.18.02
Toolholder machines specifically for STAR SV 12/20/32, SR10 / 20/32 and SB 16 to the outer piercing and turning operations for receiving inserts Type 312 at maximum penetration depth of 6:00 mm and a
Paul Horn L381.0063.05
Routers disc for milling in inner and outer contours with a cutting diameter of 63 mm and 5 blades (type 314) with a maximum groove depth of 5 mm and 6 mm slot width, Fräsdorndurchmesser is 22 mm, ve
Paul Horn L381.0080.08
Routers disc for milling in inner and outer contours with a cutting diameter of 80 mm and 8 blades (type 314) with a maximum groove depth of 5 mm and 6 mm slot width, Fräsdorndurchmesser is 27 mm, ve
Paul Horn L381.0100.10
Routers disc for milling in inner and outer contours with a cutting diameter of 100 mm and 10 blades (type 314) with a maximum groove depth of 5 mm and 6 mm slot width, Fräsdorndurchmesser is 32 mm,
Paul Horn L381.A060.13.04
Schlagmesser for producing polygons on lathes with a cutting diameter of 60 mm and 3 flutes (type 314) with maximum penetration depth of 4.5 mm, machine specific for Star SR-20J version Left.
Paul Horn L381.D080.16.04
Schlagmesser for producing polygons on lathes with a cutting diameter of 80 mm and 3 flutes (type 314) with maximum penetration depth of 5 mm, machine specific for DECO 2000 / DECO 13/20/26, version L
Paul Horn L381.D086.25.04
0 0 for producing polygons on lathes with a cutting diameter of 0 mm and 0 Cutting (Type 314) at maximum cutting depth of 0 mm, machine specific for 0, execution 0th
Paul Horn L381.G070.15.04
Schlagmesser for producing polygons on lathes with a cutting diameter of 70 mm and 3 flutes (type 314) with maximum penetration depth of 5 mm, machine specific for GLD25 / GD32, execution neutral.
Paul Horn L381.G080.16.04
Schlagmesser for producing polygons on lathes with a cutting diameter of 80 mm and 3 flutes (type 314) with maximum penetration depth of 5 mm, machine specific for SPRINT 20/32, Type neutral.
Paul Horn L381.G086.25.04
Schlagmesser for producing polygons on lathes with a cutting diameter of 86 mm and 3 flutes (type 314) with maximum penetration depth of 5 mm, machine specific for GM20-6, -35-8 / GMC35, execution Lin
Paul Horn L381.G090.22.04
Schlagmesser for producing polygons on lathes with a cutting diameter of 90 mm and 3 flutes (type 314) with maximum penetration depth of 5 mm, machine specific for SPRINT32L / -42L, execution neutral.
Paul Horn L381.G098.26.04
Schlagmesser for producing polygons on lathes with a cutting diameter of 98 mm and 3 flutes (type 314) with maximum penetration depth of 5 mm, machine specific for GM35-6, -35-8, -42-6 / GMC35,
Paul Horn L381.N090.16.04
Schlagmesser for producing polygons on lathes with a cutting diameter of 90 mm and 3 flutes (type 314) with maximum penetration depth of 5 mm, machine specific for WT250, execution Links.
Paul Horn L381.S078.30.02
Milling tool type
Paul Horn L381.S078.30.03
Schlagmesser for producing polygons on lathes with a cutting diameter of 78 mm and 3 flutes (type 314) with maximum penetration depth of 5 mm, machine specific for SG18, SG20 AG18, execution neutral.