Paul Horn 328.1423.00 TI25
The insert with a cutting diameter of 24 mm and a cutting width of 9.2 mm is suitable for T-slot milling of internal and external contours.
Paul Horn 328.1525.01 TN35
Insert with a pitch range of 1.5 - 2.5 mm or 12-20 transition / inch and a cutting circle diameter of 27.70 mm is suitable for producing internal threads in partial profile.
Paul Horn 328.3050.01 TI25
Insert with a pitch range of 3.0 - 5.0 mm or 6 - 10 transition / inch and a cutting circle diameter of 27.70 mm is suitable for producing internal threads in partial profile.
Paul Horn 328.3050.01 TN35
Insert with a pitch range of 3.0 - 5.0 mm or 6 - 10 transition / inch and a cutting circle diameter of 27.70 mm is suitable for producing internal threads in partial profile.
Paul Horn 328.4545.35.00 TA45
The insert with a cutting diameter of 27.7 mm and a cutting width of 2.6 mm is suitable for chamfering of inner and outer contours with up to 3.5 mm deep.
Paul Horn 328.5060.01 TN35
Insert with a pitch range of 5.0 - 6.0 mm or 5 - 6 Gang / inch and a cutting circle diameter of 27.70 mm is suitable for producing internal threads in partial profile.
Paul Horn 328.5511.02 TN35
Insert with a gradient from 11:00 Gang / inch and a cutting circle diameter of 27.70 mm is suitable for producing internal threads in the full profile.
Paul Horn 332.0150.2.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 332.0150.2.00 TI25
The insert with a cutting diameter of 31.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 332.0160.2.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 1.6 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 332.0160.2.00 TI25
The insert with a cutting diameter of 31.7 mm and a cutting width of 1.6 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 332.0200.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 332.0200.00 TI25
The insert with a cutting diameter of 31.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 332.0200.2.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 332.0200.2.00 TI25
The insert with a cutting diameter of 31.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 332.0250.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 332.0250.00 TI25
The insert with a cutting diameter of 31.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 332.0250.2.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 332.0250.2.00 TI25
The insert with a cutting diameter of 31.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 332.0300.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 332.0300.00 TI25
The insert with a cutting diameter of 31.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 332.0300.2.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 332.0300.2.00 TI25
The insert with a cutting diameter of 31.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 332.0350.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 3.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 332.0400.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 4 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 332.0400.00 TI25
The insert with a cutting diameter of 31.7 mm and a cutting width of 4 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 332.4545.35.00 TA45
The insert with a cutting diameter of 31.7 mm and a cutting width of 2.6 mm is suitable for Fasfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 335.0200.00 AS45
The insert with a cutting diameter of 34.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8 mm depth.
Paul Horn 335.0200.00 TI25
The insert with a cutting diameter of 34.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8 mm depth.
Paul Horn 335.0300.00 AS45
The insert with a cutting diameter of 34.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8 mm depth.
Paul Horn 335.0300.00 TI25
The insert with a cutting diameter of 34.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8 mm depth.
Paul Horn 335.0400.00 AS45
The insert with a cutting diameter of 34.7 mm and a cutting width of 4 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8 mm depth.
Paul Horn 335.0400.00 TI25
The insert with a cutting diameter of 34.7 mm and a cutting width of 4 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8 mm depth.
Paul Horn 335.0500.00 AS45
The insert with a cutting diameter of 34.7 mm and a cutting width of 5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8 mm depth.
Paul Horn 335.0500.00 TI25
The insert with a cutting diameter of 34.7 mm and a cutting width of 5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8 mm depth.
Paul Horn 335.0600.00 AS45
The insert with a cutting diameter of 34.7 mm and a cutting width of 6 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8 mm depth.
Paul Horn 335.0600.00 TI25
The insert with a cutting diameter of 34.7 mm and a cutting width of 6 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8 mm depth.
Paul Horn 340.0200
Clamping element, for secure clamping of Wendeschneiplattenpaketen Type 340
Paul Horn 340.2020.01
Toolholder with a shaft height h = 20.00 mm and stem width b = 20.00 mm is suitable for clamping of up to 2 Inserts Type 312 G (periphery ground), the maximum plunge is tmax 4:00 mm.
Paul Horn 340.2520.01
Toolholder with a shaft height h = 25.00 mm and stem width b = 20.00 mm is suitable for clamping of up to 2 Inserts Type 312 G (periphery ground), the maximum plunge is tmax 4:00 mm.
Paul Horn 340.2532.02
Toolholder with a shaft height h = 25.00 mm and stem width b = 32.00 mm is suitable for clamping of up to 4 inserts Type 312 G (periphery ground), the maximum plunge is tmax 4:00 mm.
Paul Horn 340.3232.02
Toolholder with a shaft height h = 32.00 mm and stem width b = 32.00 mm is suitable for clamping of up to 4 inserts Type 312 G (periphery ground), the maximum plunge is tmax 4:00 mm.
Paul Horn 380.0044.03A
Cutter shank with a clamping diameter of 25.00 mm and cutting circle diameter of 44.00 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove depth of 4.00 mm.
Paul Horn 380.0044.03B
Cutter shank with a clamping diameter of 25.00 mm and cutting circle diameter of 44.00 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove depth of 4.00 mm.
Paul Horn 380.0044.03E
Cutter shank with a clamping diameter of 25.00 mm and cutting circle diameter of 44.00 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove depth of 4.00 mm.
Paul Horn 380.0063.05
Cutterhead as arbor fits Fräsdorndurchmesser 22 mm and cutting circle diameter of 63 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove depth of 5 mm.
Paul Horn 380.0063.05IK
Cutterhead as arbor with Inner coolant supply fits Fräsdorndurchmesser 22 mm and cutting circle diameter of 63 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove de
Paul Horn 380.0080.08
Cutterhead as arbor fits Fräsdorndurchmesser 27 mm and cutting circle diameter of 80 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove depth of 5 mm.
Paul Horn 380.0080.08IK
Cutterhead as arbor with Inner coolant supply fits Fräsdorndurchmesser 27 mm and cutting circle diameter of 80 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove de
Paul Horn 382.0080.27.06
Routers disc fits Fräsdorndurchmesser of 27 mm, maximum groove width of 6 and cutting circle diameter of 80 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove depth
Paul Horn 382.0080.27.08
Routers disc fits Fräsdorndurchmesser of 27 mm, maximum groove width of 8 and cutting circle diameter of 80 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove depth
Paul Horn 382.0080.27.10
Routers disc fits Fräsdorndurchmesser of 27 mm, maximum groove width of 10 and cutting circle diameter of 80 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove dept
Paul Horn 382.0100.32.06
Routers disc fits Fräsdorndurchmesser of 32 mm, maximum groove width of 6 and cutting circle diameter of 100 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove dept
Paul Horn 382.0100.32.08
Routers disc fits Fräsdorndurchmesser of 32 mm, maximum groove width of 8 and cutting circle diameter of 100 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove dept
Paul Horn 382.0100.32.10
Routers disc fits Fräsdorndurchmesser of 32 mm, maximum groove width of 10 and cutting circle diameter of 100 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove dep
Paul Horn 382.0125.40.06
Routers disc fits Fräsdorndurchmesser of 40 mm, maximum groove width of 6 and cutting circle diameter of 125 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove dept
Paul Horn 382.0125.40.08
Routers disc fits Fräsdorndurchmesser of 40 mm, maximum groove width of 8 and cutting circle diameter of 125 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove dept
Paul Horn 382.0125.40.10
Routers disc fits Fräsdorndurchmesser of 40 mm, maximum groove width of 10 and cutting circle diameter of 125 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove dep
Paul Horn 382.0125.40.12
Routers disc fits Fräsdorndurchmesser of 40 mm, maximum groove width of 12 and cutting circle diameter of 125 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove dep
Paul Horn 382.0160.40.06
Routers disc fits Fräsdorndurchmesser of 40 mm, maximum groove width of 6 and cutting circle diameter of 160 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove dept
Paul Horn 382.0160.40.08
Routers disc fits Fräsdorndurchmesser of 40 mm, maximum groove width of 8 and cutting circle diameter of 160 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove dept
Paul Horn 382.0160.40.10
Routers disc fits Fräsdorndurchmesser of 40 mm, maximum groove width of 10 and cutting circle diameter of 160 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove dep
Paul Horn 382.0160.40.12
Routers disc fits Fräsdorndurchmesser of 40 mm, maximum groove width of 12 and cutting circle diameter of 160 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove dep
Paul Horn 382.0200.50.06
Routers disc fits Fräsdorndurchmesser of 50 mm, maximum groove width of 6 and cutting circle diameter of 200 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove dept
Paul Horn 382.0200.50.08
Routers disc fits Fräsdorndurchmesser of 50 mm, maximum groove width of 8 and cutting circle diameter of 200 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove dept
Paul Horn 382.0200.50.10
Routers disc fits Fräsdorndurchmesser of 50 mm, maximum groove width of 10 and cutting circle diameter of 200 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove dep
Paul Horn 382.0200.50.12
Routers disc fits Fräsdorndurchmesser of 50 mm, maximum groove width of 12 and cutting circle diameter of 200 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove dep
Paul Horn 382.0200.50.14
Routers disc fits Fräsdorndurchmesser of 50 mm, maximum groove width of 14 and cutting circle diameter of 200 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove dep
Paul Horn 383.0100.27.06
Routers disc as arbor fits Fräsdorndurchmesser of 27 mm, maximum groove width of 6 and cutting circle diameter of 100 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum gr
Paul Horn 383.0100.27.08
Routers disc as arbor fits Fräsdorndurchmesser of 27 mm, maximum groove width of 8 and cutting circle diameter of 100 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum gr
Paul Horn 383.0100.27.10
Routers disc as arbor fits Fräsdorndurchmesser of 27 mm, maximum groove width of 10 and cutting circle diameter of 100 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum g
Paul Horn 383.0200.40.06
Routers disc as arbor fits Fräsdorndurchmesser of 40 mm, maximum groove width of 6 and cutting circle diameter of 200 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum gr
Paul Horn 383.0200.40.08
Routers disc as arbor fits Fräsdorndurchmesser of 40 mm, maximum groove width of 8 and cutting circle diameter of 200 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum gr
Paul Horn 383.0200.40.10
Routers disc as arbor fits Fräsdorndurchmesser of 40 mm, maximum groove width of 10 and cutting circle diameter of 200 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum g
Paul Horn 383.0200.40.12
Routers disc type
Paul Horn 4.06.020
screw
Paul Horn 4.08.913
Screw self-locking
Paul Horn 4.09T15P
Cylindrical clamping screw with countersunk Torx PlusВ®, Torque: 5.0 Nm
Paul Horn 4.12.125
Clamping screw
Paul Horn 4.12T15EP
Cylindrical clamping screw with countersunk Torx PlusВ®, tightening torque: 4.3 Nm
Paul Horn 4.14T15P
Cylindrical clamping screw with countersunk Torx PlusВ®, Torque: 5.0 Nm
Paul Horn 4.15T15P
Cylindrical clamping screw with countersunk Torx PlusВ®, Torque: 5.0 Nm
Paul Horn 4.16T15KP
Cylindrical clamping screw with countersunk Torx PlusВ®, Torque: 5.0 Nm
Paul Horn 4.20T15P
Cylindrical clamping screw with countersunk Torx PlusВ®, Torque: 5.0 Nm
Paul Horn 4081R
Clamping element 4.081R
Paul Horn 418T15EP
Cylindrical clamping screw with countersunk Torx PlusВ® 4.18T15EP, Torque: 5.0 Nm
Paul Horn 5.08.020
screw
Paul Horn 5.10T20P
Clamping screw
Paul Horn 5.11T15P
Cylindrical clamping screw with countersunk Torx PlusВ®, Torque: 5.0 Nm
Paul Horn 5.12.03
Spring washer 5:12:03
Paul Horn 5.12T20P
Clamping screw
Paul Horn 5.13 T20P
Cylindrical clamping screw with countersunk Torx PlusВ® 5:13 T20P, tightening torque: 6.0 to 6.5 Nm
Paul Horn 5.13T20EP
Clamping screw
Paul Horn 5.13T20KP
Cylindrical clamping screw with countersunk Torx PlusВ®, tightening torque: 6.5 Nm
Paul Horn 5.14
Cylindrical clamping screw 5:14 allen size 2.5 DIN911, tightening torque 2.0 - 2.5 Nm
Paul Horn 5.14T20P
Clamping screw
Paul Horn 5.15T20P
Clamping screw
Paul Horn 5.17T20P
Clamping screw
Paul Horn 5.26T20P
Cylindrical clamping screw with countersunk Torx PlusВ®, tightening torque: 6.5 Nm
Paul Horn 5.28T20P
Cylindrical clamping screw with countersunk Torx PlusВ®, tightening torque: 6.5 Nm
Paul Horn 5.30.7984
Zylinderschraube
Paul Horn 5.30T20P
Cylindrical clamping screw with countersunk Torx PlusВ®, tightening torque: 6.5 Nm
Paul Horn 5.32.3T15P
Cylindrical clamping screw with countersunk Torx PlusВ®, tightening torque: 4.5 Nm
Paul Horn 5.32T15P
Cylindrical clamping screw with countersunk Torx PlusВ® Torx PlusВ®, Torque: 5.0 Nm
Paul Horn 5.F08T20P
Clamping screw
Paul Horn 51.27.984P
Cylindrical clamping screw with countersunk Torx PlusВ®, tightening torque 4.0 Nm
Paul Horn 5F.06T15P
Clamping screw
Paul Horn 6.075T15P
Cylindrical clamping screw with countersunk Torx PlusВ®, Torque: 5.0 Nm
Paul Horn 6.12.020
screw
Paul Horn 6.16.7991
Senkschraube
Paul Horn 6.17 T20P
Cylindrical clamping screw with countersunk Torx PlusВ® 6:17 T20P, tightening torque: 6.0 to 6.5 Nm
Paul Horn 6.17T25P
Cylindrical clamping screw with countersunk Torx PlusВ®, tightening torque: 12 Nm
Paul Horn 6.18T20P
Clamping screw
Paul Horn 6.19
Cylindrical clamping screw 6:19 with eccentric system 211, tightening torque 3.0 Nm
Paul Horn 6.20.232
Mounting screw
Paul Horn 6.20.70P
Cylindrical clamping screw with countersunk Torx PlusВ®, tightening torque: 12 Nm
Paul Horn 6.224
Turnbuckle 6224
Paul Horn 6.23 T25P
Cylindrical clamping screw with countersunk Torx PlusВ® 6:23 T25P, tightening torque: 12 Nm
Paul Horn 6.25
Clamping screw 6:25, tightening torque: 4.5 Nm, Allen 3 mm, suitable for clamping elements 11.3
Paul Horn 6.25.912
Zylinderschraube, tightening torque: 4.5 Nm, Allen 3 mm, suitable for clamping elements 11.3
Paul Horn 606.0045.22 AS45
The insert with a cutting diameter of 11.7 mm is suitable for face milling of internal and external contours with up to 1.5 mm deep.
Paul Horn 606.0110.00 TA45
The insert with a cutting diameter of 11.7 mm and a cutting width of 1.21 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm.
Paul Horn 606.0130.00 TA45
The insert with a cutting diameter of 11.7 mm and a cutting width of 1.41 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm.
Paul Horn 606.0150.00 AS45
The insert with a cutting diameter of 11.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm.
Paul Horn 606.0150.00 TA45
The insert with a cutting diameter of 11.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm.
Paul Horn 606.0160.00 AS45
The insert with a cutting diameter of 11.7 mm and a cutting width of 1.71 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm.
Paul Horn 606.0160.00 TA45
The insert with a cutting diameter of 11.7 mm and a cutting width of 1.71 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm.
Paul Horn 606.0200.00 AS45
The insert with a cutting diameter of 11.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm.
Paul Horn 606.0200.00 TA45
The insert with a cutting diameter of 11.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm.
Paul Horn 606.0250.00 AS45
The insert with a cutting diameter of 11.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm.
Paul Horn 606.0250.00 TA45
The insert with a cutting diameter of 11.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with depths up to 2.5 mm.
Paul Horn 606.0515.01 TA45
The insert with partial profile and a cutting circle diameter 10.00 mm is suitable for thread milling metric threads with a pitch of 0.50mm.
Paul Horn 606.0720.01 TA45
The insert with partial profile and a cutting circle diameter of 11.70 mm is suitable for thread milling metric threads with a pitch of 1.00 mm.
Paul Horn 606.1515.20 TA45
The insert with a cutting diameter of 11.7 mm is suitable for chamfering of inner and outer contours.
Paul Horn 606.2020.20 TA45
The insert with a cutting diameter of 11.7 mm is suitable for chamfering of inner and outer contours.
Paul Horn 606.3030.20 TA45
The insert with a cutting diameter of 11.7 mm is suitable for chamfering of inner and outer contours.
Paul Horn 606.4545.20 TA45
The insert with a cutting diameter of 11.7 mm is suitable for chamfering of inner and outer contours.
Paul Horn 606.5514.02 TA45
The insert with full profile and a cutting circle diameter of 11.70 mm is suitable for thread milling of Whitworth pipe threads with a pitch of 14 Gg / inch.
Paul Horn 606.5519.02 TA45
The insert with full profile and a cutting circle diameter of 11.70 mm is suitable for thread milling of Whitworth pipe threads with a pitch of 19 Gg / inch.
Paul Horn 606.5519.10.02 TA45
The insert with full profile and a cutting circle diameter of 9.70 mm is suitable for thread milling of Whitworth pipe threads with a pitch of 19 Gg / inch.
Paul Horn 606.PLT6.08 AS45
The insert with a cutting diameter of 11.7 mm is suitable for face milling of internal and external contours with up to 3.2 mm deep.
Paul Horn 606.PLT6.08 TI25
The insert with a cutting diameter of 11.7 mm is suitable for face milling of internal and external contours with up to 3.2 mm deep.
Paul Horn 608.0150.00 AS45
The insert with a cutting diameter of 15.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 608.0150.00 TI25
The insert with a cutting diameter of 15.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 608.0200.00 AS45
The insert with a cutting diameter of 15.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 608.0200.00 TI25
The insert with a cutting diameter of 15.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 608.0250.00 AS45
The insert with a cutting diameter of 15.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 608.0250.00 TI25
The insert with a cutting diameter of 15.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 608.0720.01 TI25
Insert with a pitch range of 1.0 - 2.0 mm or 12-32 transition / inch and a cutting circle diameter of 15.70 mm is suitable for producing internal threads in partial profile.
Paul Horn 608.1325.01 TA45
The insert with partial profile and a cutting circle diameter 13.20 mm is suitable for thread milling metric threads with a gradient of 2:50 mm.
Paul Horn 608.1515.20 TA45
The insert with a cutting diameter of 15.7 mm is suitable for chamfering of inner and outer contours.
Paul Horn 608.2020.20 TA45
The insert with a cutting diameter of 15.7 mm is suitable for chamfering of inner and outer contours.
Paul Horn 608.2530.01 TI25
Insert with a pitch range of 2.5 - 3.0 mm or 8-32 transition / inch and a cutting circle diameter of 15.70 mm is suitable for producing internal threads in partial profile.
Paul Horn 608.3030.20 TA45
The insert with a cutting diameter of 15.7 mm is suitable for chamfering of inner and outer contours.
Paul Horn 608.4545.20 TI25
Insert with a cutting diameter of 15.7 is suitable for chamfering of inner and outer contours up to 1.7 x 45 В°.
Paul Horn 608.5514.02 AS45
The insert full profile and a cutting circle diameter of 13:50 mm is suitable for thread milling of Whitworth pipe threads with a pitch of 14 Gg / inch.
Paul Horn 608.5514.02 TA45
The insert with full profile and a cutting circle diameter of 13:50 mm is suitable for thread milling of Whitworth pipe threads with a pitch of 14 Gg / inch.
Paul Horn 611.0110.00 TI25
The insert with a cutting diameter of 17.7 mm and a cutting width of 1.21 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 611.0130.00 AS45
The insert with a cutting diameter of 17.7 mm and a cutting width of 1.41 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 611.0130.00 TI25
The insert with a cutting diameter of 17.7 mm and a cutting width of 1.41 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 611.0150.00 AS45
The insert with a cutting diameter of 17.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 611.0150.00 TI25
The insert with a cutting diameter of 17.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 611.0160.00 AS45
The insert with a cutting diameter of 17.7 mm and a cutting width of 1.71 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 611.0160.00 TI25
The insert with a cutting diameter of 17.7 mm and a cutting width of 1.71 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 611.0200.00 AS45
The insert with a cutting diameter of 17.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 611.0200.00 TI25
The insert with a cutting diameter of 17.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 611.0250.00 AS45
The insert with a cutting diameter of 17.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 611.0250.00 TI25
The insert with a cutting diameter of 17.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 611.0300.00 AS45
The insert with a cutting diameter of 17.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 611.0300.00 TI25
The insert with a cutting diameter of 17.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 611.0400.00 AS45
The insert with a cutting diameter of 17.7 mm and a cutting width of 4 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 611.0515.01 TA45
Insert with a pitch range of 0.5 - 1.5 mm or 18 - 48 transition / inch and a cutting circle diameter of 17.70 mm is suitable for producing internal threads in partial profile.
Paul Horn 611.0720.01 TI25
Insert with a pitch range of 1.0 - 2.0 mm or 12-32 transition / inch and a cutting circle diameter of 17.70 mm is suitable for producing internal threads in partial profile.
Paul Horn 611.1515.20 TA45
The insert with a cutting diameter of 17.7 mm is suitable for chamfering of inner and outer contours.
Paul Horn 611.2020.20 TA45
The insert with a cutting diameter of 17.7 mm is suitable for chamfering of inner and outer contours.
Paul Horn 611.2535.01 TI25
Insert with a pitch range of 2.5 - 3.5 mm or 6 individual - 12 speeds / inch and a cutting circle diameter of 17.70 mm is suitable for producing internal threads in partial profile.
Paul Horn 611.3030.20 TA45
The insert with a cutting diameter of 17.7 mm is suitable for chamfering of inner and outer contours.
Paul Horn 611.4545.20 TI25
The insert with a cutting diameter of 17.7 mm is suitable for chamfering of inner and outer contours.
Paul Horn 611.PL61.62 AS45
The insert with a cutting diameter of 17.7 mm is suitable for face milling of internal and external contours with up to 5.7 mm deep.
Paul Horn 611.PL61.62 TF45
The insert with a cutting diameter of 17.7 mm is suitable for face milling of internal and external contours with up to 5.7 mm deep.
Paul Horn 611.PL61.62 TI25
The insert with a cutting diameter of 17.7 mm is suitable for face milling of internal and external contours with up to 5.7 mm deep.
Paul Horn 613.0015.25 AS45
The insert with a cutting diameter of 21.7 mm is suitable for face milling of internal and external contours with up to mm depth.
Paul Horn 613.0045.25 AS45
The insert with a cutting diameter of 21.7 mm is suitable for face milling of internal and external contours with up to 3.5 mm deep.
Paul Horn 613.0100.1.00 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 1 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn 613.0150.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn 613.0150.00 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn 613.0200.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn 613.0200.00 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn 613.0250.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn 613.0250.00 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn 613.0300.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn 613.0300.00 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn 613.0400.00 AS45
The insert with a cutting diameter of 21.7 mm and a cutting width of 4 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn 613.0400.00 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 4 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn 613.0720.01 TI25
Insert with a pitch range of 1.0 - 2.0 mm or 12-32 transition / inch and a cutting circle diameter of 21.70 mm is suitable for producing internal threads in partial profile.
Paul Horn 613.1515.20 TA45
The insert with a cutting diameter of 21.7 mm is suitable for chamfering of inner and outer contours.
Paul Horn 613.2020.20 TA45
The insert with a cutting diameter of 21.7 mm is suitable for chamfering of inner and outer contours.
Paul Horn 613.2545.01 TI25
Insert with a pitch range of 2.5 - 4.5 mm or 6 individual - 12 speeds / inch and a cutting circle diameter of 21.70 mm is suitable for producing internal threads in partial profile.
Paul Horn 613.3030.20 TA45
The insert with a cutting diameter of 21.7 mm is suitable for chamfering of inner and outer contours.
Paul Horn 613.3972.050.1 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 613.3972.050.2 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 613.3972.050.3 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 613.3972.050.4 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 613.3972.050.5 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 613.3972.050.6 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 613.3972.050.7 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 613.3972.050.8 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 613.3972.100.1 AS45
The insert is suitable for gear milling for spur gears with involute.
Paul Horn 613.3972.100.2 AS45
The insert is suitable for gear milling for spur gears with involute.
Paul Horn 613.3972.100.3 AS45
The insert is suitable for gear milling for spur gears with involute.
Paul Horn 613.3972.100.4 AS45
The insert is suitable for gear milling for spur gears with involute.
Paul Horn 613.3972.100.5 AS45
The insert is suitable for gear milling for spur gears with involute.
Paul Horn 613.3972.100.6 AS45
The insert is suitable for gear milling for spur gears with involute.
Paul Horn 613.3972.100.7 AS45
The insert is suitable for gear milling for spur gears with involute.
Paul Horn 613.3972.100.8 AS45
The insert is suitable for gear milling for spur gears with involute.
Paul Horn 613.3972.125.1 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 613.3972.125.2 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 613.3972.125.3 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 613.3972.125.4 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 613.3972.125.5 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 613.3972.125.6 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 613.3972.125.7 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 613.3972.125.8 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 613.3972.150.1 AS45
The insert is suitable for gear milling for spur gears with involute.
Paul Horn 613.3972.150.2 AS45
The insert is suitable for gear milling for spur gears with involute.
Paul Horn 613.3972.150.3 AS45
The insert is suitable for gear milling for spur gears with involute.
Paul Horn 613.3972.150.4 AS45
The insert is suitable for gear milling for spur gears with involute.
Paul Horn 613.3972.150.5 AS45
The insert is suitable for gear milling for spur gears with involute.
Paul Horn 613.3972.150.6 AS45
The insert is suitable for gear milling for spur gears with involute.
Paul Horn 613.3972.150.7 AS45
The insert is suitable for gear milling for spur gears with involute.
Paul Horn 613.3972.150.8 AS45
The insert is suitable for gear milling for spur gears with involute.
Paul Horn 613.4545.20 TI25
The insert with a cutting diameter of 21.7 mm is suitable for chamfering of inner and outer contours.
Paul Horn 613.5511.02 TA45
The insert with full profile and a cutting circle diameter of 21.70 mm is suitable for thread milling of Whitworth pipe threads with a pitch of 11 Gg / inch.
Paul Horn 613.5511.02 TI25
The insert with a cutting diameter of 21.70 mm is suitable for thread milling of Whitworth pipe threads with a pitch of 11 Gg / inch.
Paul Horn 613.PL61.62 AS45
The insert with a cutting diameter of 21.7 mm is suitable for face milling of internal and external contours with up to 5.7 mm deep.
Paul Horn 613.PL61.62 TF45
The insert with a cutting diameter of 21.7 mm is suitable for face milling of internal and external contours with up to 5.7 mm deep.
Paul Horn 613.PL61.62 TI25
The insert with a cutting diameter of 21.7 mm is suitable for face milling of internal and external contours with up to 5.7 mm deep.
Paul Horn 613.PLT6.15 AS45
The insert with a cutting diameter of 21.7 mm is suitable for face milling of internal and external contours with up to 5.7 mm deep.
Paul Horn 613.PLT6.15 TI25
The insert with a cutting diameter of 21.7 mm is suitable for face milling of internal and external contours with up to 5.7 mm deep.
Paul Horn 614T25P
Cylindrical clamping screw with countersunk Torx PlusВ® 6.14T25P, tightening torque 7.0 Nm
Paul Horn 62.000.16
Clamping nut, suitable for collet chucks ER 16, clamping thread M19x1
Paul Horn 62.000.20
Clamping nut, suitable for collet chucks ER 20, clamping thread M24x1
Paul Horn 62.600.16
Clamping nut, suitable for collet chucks ER 16, clamping thread M19x1, sealable
Paul Horn 62.600.20
Clamping nut, suitable for collet chucks ER 20, clamping thread M24x1, sealable
Paul Horn 628.0100.2.00 TI25
The insert with a cutting diameter of 28 mm and a cutting width of 1 mm is suitable for separating milling of internal and external contours with up to 9.3 mm deep.
Paul Horn 628.0120.2.00 TI25
The insert with a cutting diameter of 28 mm and a cutting width of 1.2 mm is suitable for separating milling of internal and external contours with up to 9.3 mm deep.
Paul Horn 628.0130.00 AS45
Insert with a cutting width of 1.41 mm (nominal size Nw = 1.3 mm) and cutting circle diameter of 27.7 is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum gro
Paul Horn 628.0130.00 TI25
The insert with a cutting diameter of 27.7 mm and a cutting width of 1.41 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 6.5 mm deep.
Paul Horn 628.0150.2.00 AS45
The insert with a cutting diameter of 28 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 9.3 mm deep.
Paul Horn 628.0150.2.00 TI25
The insert with a cutting diameter of 28 mm and a cutting width of 1.5 mm is suitable for separating milling of internal and external contours with up to 9.3 mm deep.
Paul Horn 628.0160.00 AS45
Insert with a cutting width of 1.71 mm (nominal size Nw = 1.6 mm) and cutting circle diameter of 27.7 is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum gro
Paul Horn 628.0160.00 TI25
The insert with a cutting diameter of 27.7 mm and a cutting width of 1.71 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 6.5 mm deep.
Paul Horn 628.0160.2.00 AS45
The insert with a cutting diameter of 28 mm and a cutting width of 1.6 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 9.3 mm deep.
Paul Horn 628.0160.2.00 TI25
The insert with a cutting diameter of 28 mm and a cutting width of 1.6 mm is suitable for separating milling of internal and external contours with up to 9.3 mm deep.
Paul Horn 628.0185.00 AS45
Insert with a cutting width of 1.96 mm (nominal size Nw = 1.85 mm) and cutting circle diameter of 27.7 is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum gr
Paul Horn 628.0185.00 TI25
The insert with a cutting diameter of 27.7 mm and a cutting width of 1.96 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 6.5 mm deep.
Paul Horn 628.0200.2.00 AS45
The insert with a cutting diameter of 28 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 9.3 mm deep.
Paul Horn 628.0200.2.00 TI25
The insert with a cutting diameter of 28 mm and a cutting width of 2 mm is suitable for separating milling of internal and external contours with up to 9.3 mm deep.
Paul Horn 628.0215.00 AS45
Insert with a cutting width of 26.2 mm (nominal size Nw = 2.15 mm) and cutting circle diameter of 27.7 is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum gr
Paul Horn 628.0215.00 TI25
The insert with a cutting diameter of 27.7 mm and a cutting width of 2.26 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 6.5 mm deep.
Paul Horn 628.0240.2.00 AS45
The insert with a cutting diameter of 28 mm and a cutting width of 2.4 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 9.3 mm deep.
Paul Horn 628.0240.2.00 TI25
The insert with a cutting diameter of 28 mm and a cutting width of 2.4 mm is suitable for separating milling of internal and external contours with up to 9.3 mm deep.
Paul Horn 628.0250.00 AS45
The insert with a cutting diameter of 27.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 6.5 mm deep.
Paul Horn 628.0250.00 TI25
The insert with a cutting diameter of 27.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 6.5 mm deep.
Paul Horn 628.0250.2.00 AS45
The insert with a cutting diameter of 28 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 9.3 mm deep.
Paul Horn 628.0250.2.00 TI25
The insert with a cutting diameter of 28 mm and a cutting width of 2.5 mm is suitable for separating milling of internal and external contours with up to 9.3 mm deep.
Paul Horn 628.0265.00 AS45
Insert with a cutting width of 2.76 mm (nominal size Nw = 2.65 mm) and cutting circle diameter of 27.7 is suitable for producing Seegerringnuten DIN 471/472 on inner and outer contours with maximum gr
Paul Horn 628.0265.00 TI25
The insert with a cutting diameter of 27.7 mm and a cutting width of 2.76 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 6.5 mm deep.
Paul Horn 628.0300.00 AS45
The insert with a cutting diameter of 27.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 6.5 mm deep.
Paul Horn 628.0300.00 TI25
The insert with a cutting diameter of 27.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 6.5 mm deep.
Paul Horn 628.0350.00 AS45
The insert with a cutting diameter of 27.7 mm and a cutting width of 3.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 6.5 mm deep.
Paul Horn 628.0350.00 TI25
The insert with a cutting diameter of 27.7 mm and a cutting width of 3.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 6.5 mm deep.
Paul Horn 628.0400.00 AS45
The insert with a cutting diameter of 27.7 mm and a cutting width of 4 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 6.5 mm deep.
Paul Horn 628.0400.00 TI25
The insert with a cutting diameter of 27.7 mm and a cutting width of 4 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 6.5 mm deep.
Paul Horn 628.0800.00 AS45
Insert 628.0080.00 AN25
Paul Horn 628.1525.01 TI25
Insert with a pitch range of 1.5 - 2.5 mm or 12-20 transition / inch and a cutting circle diameter of 27.70 mm is suitable for producing internal threads in partial profile.
Paul Horn 628.3030.20 TA45
The insert with a cutting diameter of 27.7 mm is suitable for chamfering of inner and outer contours.
Paul Horn 628.3050.01 TI25
Insert with a pitch range of 3.0 - 5.0 mm or 6 - 10 transition / inch and a cutting circle diameter of 27.70 mm is suitable for producing internal threads in partial profile.
Paul Horn 628.3972.175.1 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 628.3972.175.2 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 628.3972.175.3 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 628.3972.175.4 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 628.3972.175.5 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 628.3972.175.6 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 628.3972.175.7 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 628.3972.175.8 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 628.3972.200.1 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 628.3972.200.2 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 628.3972.200.3 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 628.3972.200.4 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 628.3972.200.5 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 628.3972.200.6 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 628.3972.200.7 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 628.3972.200.8 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 628.4545.20 TA45
The insert with a cutting diameter of 27.7 mm is suitable for chamfering of inner and outer contours.
Paul Horn 628.5060.01 TI25
Insert with a pitch range of 5.0 - 6.0 mm or 5 - 6 Gang / inch and a cutting circle diameter of 27.70 mm is suitable for producing internal threads in partial profile.
Paul Horn 628.5511.02 TN35
Insert with a gradient of 0 transition / inch and a cutting circle diameter of 27.70 mm is suitable for producing internal threads in the full profile.
Paul Horn 628.PL61.62 AS45
The insert with a cutting diameter of 27.7 mm is suitable for face milling of internal and external contours with up to 5.7 mm deep.
Paul Horn 628.PL61.62 TF45
The insert with a cutting diameter of 27.7 mm is suitable for face milling of internal and external contours with up to 5.7 mm deep.
Paul Horn 628.PL61.62 TI25
Insert with a cutting diameter of 27.7 mm and a corner radius of 0.2 mm, is suitable for face milling with maximum delivery of 5.7 mm.
Paul Horn 632.0100.2.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 1 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 632.0120.2.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 1.2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 632.0150.2.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 632.0150.2.00 TA45
The insert with a cutting diameter of 31.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 632.0160.2.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 1.6 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 632.0160.2.00 TA45
The insert with a cutting diameter of 31.7 mm and a cutting width of 1.6 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 632.0200.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 632.0200.00 TA45
The insert with a cutting diameter of 31.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 632.0200.2.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 632.0200.2.00 TA45
The insert with a cutting diameter of 31.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 632.0250.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 632.0250.00 TA45
The insert with a cutting diameter of 31.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 632.0250.2.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 632.0250.2.00 TA45
The insert with a cutting diameter of 31.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 632.0300.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 632.0300.00 TA45
The insert with a cutting diameter of 31.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 632.0300.2.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 632.0300.2.00 TA45
The insert with a cutting diameter of 31.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10 mm depth.
Paul Horn 632.0400.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 4 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 632.0400.00 TA45
The insert with a cutting diameter of 31.7 mm and a cutting width of 4 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 632.2545.01 TI25
Cutting plate coated TiCN
Paul Horn 632.3972.225.2 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 632.3972.225.3 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 632.3972.225.4 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 632.3972.225.5 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 632.3972.225.6 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 632.3972.225.7 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 632.3972.225.8 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 632.4060.01 TI25
Insert with a pitch range of 4.0 - 6.0 mm or 0 transition / inch and a cutting circle diameter of 31.7 mm is suitable for producing internal threads in partial profile.
Paul Horn 635.3972.225.1 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.250.1 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.250.2 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.250.3 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.250.4 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.250.5 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.250.6 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.250.7 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.250.8 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.275.1 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.275.2 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.275.4 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.275.5 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.275.6 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.275.7 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.275.8 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.300.1 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.300.2 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.300.3 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.300.4 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.300.5 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.300.6 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 635.3972.300.8 AS45
The TiAlN nano-structured coated carbide insert is suitable for gear milling for spur gears with involute
Paul Horn 636.0110.2.00 AS45
The insert with a cutting diameter of 35.7 mm and a cutting width of 1.1 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 12 mm depth.
Paul Horn 636.0130.2.00 AS45
The insert with a cutting diameter of 35.7 mm and a cutting width of 1.3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 12 mm depth.
Paul Horn 636.0150.00 AS45
The insert with a cutting diameter of 35.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10.2 mm depth.
Paul Horn 636.0150.00 TA45
The insert with a cutting diameter of 35.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10.2 mm depth.
Paul Horn 636.0150.2.00 AS45
The insert with a cutting diameter of 35.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 12 mm depth.
Paul Horn 636.0150.2.00 TA45
The insert with a cutting diameter of 35.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 12 mm depth.
Paul Horn 636.0200.00 AS45
The insert with a cutting diameter of 35.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10.2 mm depth.
Paul Horn 636.0200.00 TA45
The insert with a cutting diameter of 35.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10.2 mm depth.
Paul Horn 636.0200.2.00 AS45
The insert with a cutting diameter of 35.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 12 mm depth.
Paul Horn 636.0200.2.00 TA45
The insert with a cutting diameter of 35.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 12 mm depth.
Paul Horn 636.0250.00 AS45
The insert with a cutting diameter of 35.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10.2 mm depth.
Paul Horn 636.0250.00 TA45
The insert with a cutting diameter of 35.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10.2 mm depth.
Paul Horn 636.0250.2.00 AS45
The insert with a cutting diameter of 35.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 12 mm depth.
Paul Horn 636.0250.2.00 TA45
The insert with a cutting diameter of 35.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 12 mm depth.
Paul Horn 636.0300.00 AS45
The insert with a cutting diameter of 35.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10.2 mm depth.
Paul Horn 636.0300.00 TA45
The insert with a cutting diameter of 35.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 10.2 mm depth.
Paul Horn 713.0040.00 AN25
The insert with a cutting diameter of 21.7 mm and a cutting width of 0.4 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 2.3 mm deep.
Paul Horn 713.0050.00 AN25
The insert with a cutting diameter of 21.7 mm and a cutting width of 0.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 2.8 mm deep.
Paul Horn 713.0080.00 AN25
The insert with a cutting diameter of 21.7 mm and a cutting width of 0.8 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn 713.0100.00 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 1 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn 713.0150.00 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 1.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn 713.0200.00 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn 713.0250.00 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn 713.0300.00 TI25
The insert with a cutting diameter of 21.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 4.5 mm deep.
Paul Horn 713.PL35.15.02 TI25
The insert with a cutting diameter of 21.7 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 3.5 mm deep.
Paul Horn 8.25.351
Mounting screw
Paul Horn 8.3
Clamping element suitable for tool holder types: 240
Paul Horn 8.4
Clamping element suitable for tool holder types: 240
Paul Horn 932.0200.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 2 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 932.0250.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 2.5 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 932.0300.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 3 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 932.0400.00 AS45
The insert with a cutting diameter of 31.7 mm and a cutting width of 4 mm is suitable for Nutzirkularfräsen of inner and outer contours with up to 8.3 mm deep.
Paul Horn 960.A.0.845.0000.IK
Piercing holding piece for height adjustable inputs and Abstechsystem 960, matching base holder z. B. 960.BMT85.C0.00101
Paul Horn 960.A.0.845.0002.IK
Piercing holding piece for height adjustable inputs and Abstechsystem 960, matching base holder z. B. 960.BMT85.C0.00101
Paul Horn 960.BMT32.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT38.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT40.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT42.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT45.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT45.C0.00201
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT55.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT55.C0.00201
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT55.C0.00301
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT55.C0.00401
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT60.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT65.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT65.C0.00201
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT65.C0.00301
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT68.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT75.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT80.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT80.C0.00201
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.BMT85.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.I.0.845.0001.IK
Piercing holding piece for height adjustable inputs and Abstechsystem 960, matching base holder z. B. 960.BMT85.C0.00101
Paul Horn 960.I.0.845.0003.IK
Piercing holding piece for height adjustable inputs and Abstechsystem 960, matching base holder z. B. 960.BMT85.C0.00101
Paul Horn 960.MAZ40.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.MAZ40.C0.00201
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.MAZ40.C0.00301
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.MAZ40.C0.00401
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.MAZ50.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.Q.0.845.0000.IK
Piercing holding piece for height adjustable inputs and Abstechsystem 960, matching base holder 960.VDI30.B0.00101 and 960.VDI40.B0.00101
Paul Horn 960.VDI25.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.VDI30.B0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.Q.0.845.0000.IK
Paul Horn 960.VDI30.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.VDI40.B0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.Q.0.845.0000.IK
Paul Horn 960.VDI40.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 960.VDI50.B0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.Q.0.845.0001.IK
Paul Horn 960.VDI50.C0.00101
Basic holder. For height adjustable inputs and Abstechsystem 960, Suitable eg piercing holding piece 960.A.0.845.0000.IK
Paul Horn 962.08.01R
Toolholder for sliding head with a shaft height h = 8.00 mm and stem width b = 8.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 962.08.02L
Toolholder for sliding head with a shaft height h = 8.00 mm and stem width b = 8.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 962.08.03R
Toolholder for sliding head with a shaft height h = 8.00 mm and stem width b = 8.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 962.08.04L
Toolholder for sliding head with a shaft height h = 8.00 mm and stem width b = 8.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 962.10.01R
Toolholder for sliding head with a shaft height h = 10:00 mm and stem width b = 10:00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 962.10.02L
Toolholder for sliding head with a shaft height h = 10:00 mm and stem width b = 10:00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 962.10.03R
Toolholder for sliding head with a shaft height h = 10:00 mm and stem width b = 10:00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 962.10.04L
Toolholder for sliding head with a shaft height h = 10:00 mm and stem width b = 10:00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 962.12.01R
Toolholder for sliding head with a shaft height h = 12.00 mm and stem width b = 12.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 962.12.02L
Toolholder for sliding head with a shaft height h = 12.00 mm and stem width b = 12.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 962.12.03R
Toolholder for sliding head with a shaft height h = 12.00 mm and stem width b = 12.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 962.12.04L
Toolholder for sliding head with a shaft height h = 12.00 mm and stem width b = 12.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 962.16.01R
Toolholder for sliding head with a shaft height h = 16.00mm and stem width b = 16.00mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 32.00 mm.
Paul Horn 962.16.02L
Toolholder for sliding head with a shaft height h = 16.00mm and stem width b = 16.00mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 32.00 mm.
Paul Horn 962.16.03R
Toolholder for sliding head with a shaft height h = 16.00mm and stem width b = 16.00mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 32.00 mm.
Paul Horn 962.16.04L
Toolholder for sliding head with a shaft height h = 16.00mm and stem width b = 16.00mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 32.00 mm.
Paul Horn 962.20.01R
Toolholder for sliding head with a shaft height h = 20.00 mm and stem width b = 20.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 32.00 mm.
Paul Horn 962.20.02L
Toolholder for sliding head with a shaft height h = 20.00 mm and stem width b = 20.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 32.00 mm.
Paul Horn 962.20.03R
Toolholder for sliding head with a shaft height h = 20.00 mm and stem width b = 20.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 32.00 mm.
Paul Horn 962.20.04L
Toolholder for sliding head with a shaft height h = 20.00 mm and stem width b = 20.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 32.00 mm.
Paul Horn 963.08.01R
Toolholder for sliding head with a shaft height h = 8.00 mm and stem width b = 8.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 963.08.02L
Toolholder for sliding head with a shaft height h = 8.00 mm and stem width b = 8.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 963.10.01R
Toolholder for sliding head with a shaft height h = 10:00 mm and stem width b = 10:00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 963.10.02L
Toolholder for sliding head with a shaft height h = 10:00 mm and stem width b = 10:00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 963.12.01R
Toolholder for sliding head with a shaft height h = 12.00 mm and stem width b = 12.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 963.12.02 L
Tool holders for long turning with a shaft height h = 12.00 mm and stem width b = 12.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 26.00 mm.
Paul Horn 963.16.01R
Toolholder for sliding head with a shaft height h = 16.00mm and stem width b = 16.00mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 32.00 mm.
Paul Horn 963.16.02L
Toolholder for sliding head with a shaft height h = 16.00mm and stem width b = 16.00mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 32.00 mm.
Paul Horn 963.20.01R
Toolholder for sliding head with a shaft height h = 20.00 mm and stem width b = 20.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 32.00 mm.
Paul Horn 963.20.02L
Toolholder for sliding head with a shaft height h = 20.00 mm and stem width b = 20.00 mm is suitable for clamping of cutting inserts of the type 105, the maximum rod diameter is 32.00 mm.
Paul Horn 974.L1010.04 IK
Toolholder Graf for sliding head with a shaft height h = 10:00 mm and stem width b = 10:00 mm is suitable for clamping of inserts type S274, the maximum rod diameter is 25.00 mm.
Paul Horn 974.L1212.04 IK
Toolholder Graf for sliding head with a shaft height h = 12.00 mm and stem width b = 12.00 mm is suitable for clamping of inserts type S274, the maximum rod diameter is 25.00 mm.
Paul Horn 974.L1616.04 IK
Toolholder Graf for sliding head with a shaft height h = 16.00mm and stem width b = 16.00mm is suitable for clamping of inserts type S274, the maximum rod diameter is 25.00 mm.
Paul Horn 974.L2020.04 IK
Toolholder Graf for sliding head with a shaft height h = 20.00 mm and stem width b = 20.00 mm is suitable for clamping of inserts type S274, the maximum rod diameter is 25.00 mm.
Paul Horn 974.R1010.04 IK
Toolholder Graf for sliding head with a shaft height h = 10:00 mm and stem width b = 10:00 mm is suitable for clamping of inserts type S274, the maximum rod diameter is 25.00 mm.
Paul Horn 974.R1212.04 IK
Toolholder Graf for sliding head with a shaft height h = 12.00 mm and stem width b = 12.00 mm is suitable for clamping of inserts type S274, the maximum rod diameter is 25.00 mm.
Paul Horn 974.R1616.04 IK
Toolholder Graf for sliding head with a shaft height h = 16.00mm and stem width b = 16.00mm is suitable for clamping of inserts type S274, the maximum rod diameter is 25.00 mm.
Paul Horn 974.R2020.04 IK
Toolholder Graf for sliding head with a shaft height h = 20.00 mm and stem width b = 20.00 mm is suitable for clamping of inserts type S274, the maximum rod diameter is 25.00 mm.
Paul Horn ABS-32-380.0044.03
Cutterhead ABS 32-380.0044.03 monoblock cutter with ABS32 cuts point and cutting circle diameter of 44 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove depth of 4
Paul Horn ABS-40-380.0050.04
Cutterhead ABS 40-380.0050.04 monoblock cutter with ABS40 cuts point and cutting circle diameter of 50 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove depth of 4.
Paul Horn ABS-40-380.0063.05
Cutterhead ABS 40-380.0063.05 monoblock cutter with ABS40 cuts point and cutting circle diameter of 63 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove depth of 5
Paul Horn ABS-50-380.0063.05
Cutterhead ABS 50-380.0063.05 monoblock cutter with ABS50 cuts point and cutting circle diameter of 63 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove depth of 5
Paul Horn ABS-50-380.0080.08
Cutterhead ABS 50-380.0080.08 monoblock cutter with ABS50 cuts point and cutting circle diameter of 80 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove depth of 5
Paul Horn ABS-63-380.0080.08
Cutterhead ABS 63-380.0080.08 monoblock cutter with ABS63 cuts point and cutting circle diameter of 80 mm is suitable for Nutzirkularfräsen of inner and outer contours with maximum groove depth of 5
Paul Horn ADR.016.135.01
adapter
Paul Horn ADR.019.140.02
adapter
Paul Horn ADR.024.162.03
adapter
Paul Horn ADR.029.187.04
adapter
Paul Horn ADR.036.190.05
adapter
Paul Horn ADR.044.190.06
adapter
Paul Horn ADR.052.185.06
adapter
Paul Horn ADR.061.185.07
adapter
Paul Horn AIH.974.L 1010.K04
Toolholder for sliding head with a shaft height h = 10:00 mm and stem width b = 10:00 mm is suitable as a double clamp holders for clamping of cutting inserts of the type 105 for internal machining an
Paul Horn AIH.974.L 1212.K04
Toolholder for sliding head with a shaft height h = 12.00 mm and stem width b = 12.00 mm is suitable as a double clamp holders for clamping of cutting inserts of the type 105 for internal machining an
Paul Horn AIH.974.L 1616.K04
Toolholder for sliding head with a shaft height h = 16.00mm and stem width b = 16.00mm is suitable as a double clamp holders for clamping of cutting inserts of the type 105 for internal machining and
Paul Horn AIH.974.L 2020.K04
Toolholder for sliding head with a shaft height h = 20.00 mm and stem width b = 20.00 mm is suitable as a double clamp holders for clamping of cutting inserts of the type 105 for internal machining an
Paul Horn AIH.974.R 1010.K04
Toolholder for sliding head with a shaft height h = 10:00 mm and stem width b = 10:00 mm is suitable as a double clamp holders for clamping of cutting inserts of the type 105 for internal machining an
Paul Horn AIH.974.R 1212.K04
Toolholder for sliding head with a shaft height h = 12.00 mm and stem width b = 12.00 mm is suitable as a double clamp holders for clamping of cutting inserts of the type 105 for internal machining an
Paul Horn AIH.974.R 1616.K04
Toolholder for sliding head with a shaft height h = 16.00mm and stem width b = 16.00mm is suitable as a double clamp holders for clamping of cutting inserts of the type 105 for internal machining and
Paul Horn AIH.974.R 2020.K04
Toolholder for sliding head with a shaft height h = 20.00 mm and stem width b = 20.00 mm is suitable as a double clamp holders for clamping of cutting inserts of the type 105 for internal machining an
Paul Horn B00 22 01
Linsenschraube
Paul Horn B00 22 04
Linsenschraube
Paul Horn B00 22 05
Linsenschraube
Paul Horn B02.2025.18.AM
Fine boring head for Boring in the diameter range of 20 mm to 25 mm.
Paul Horn B02.22530.18.AM
Fine boring head for Boring in the diameter range from 22.5 mm to 30 mm.
Paul Horn B05 40 20 067
Fine boring head for receiving drill rods with shank diameter 16 mm.
Paul Horn B05.050.200206
Plate holder for Boring in the diameter range of 20 mm to 39 mm.
Paul Horn B05.050.200406
Plate holder for Boring in the diameter range of 38 mm to 67 mm.
Paul Horn B05.050.200609
Plate holder for Boring in the diameter range of 66 mm to 88 mm.
Paul Horn B05.0516
Reducing bush for receiving drill rods with shank diameter 5 mm.
Paul Horn B05.0616
Reducing bush for receiving drill rods with shank diameter 6 mm.
Paul Horn B05.0816
Reducing bush for receiving drill rods with shank diameter 8 mm.
Paul Horn B05.1016
Reducing bush for receiving drill rods with shank diameter 10 mm.
Paul Horn B05.1216
Reducing bush for receiving drill rods with shank diameter 12 mm.
Paul Horn B05.HM05.0610.1
Drill rod with shaft diameter 5 mm.
Paul Horn B05.HM06.0711.1
Drill rod with shaft diameter 6 mm.
Paul Horn B05.HM08.0913.1
Drill rod with shaft diameter 8 mm.
Paul Horn B05.HM10.1216.1
Drill rod with shaft diameter 10 mm.
Paul Horn B05.HM12.1418.1
Drill rod with shaft diameter 12 mm.
Paul Horn B05.HM16.1620.1
Drill rod with shaft diameter 16 mm.